Fixtures
orient and afix UUT.
See Also: Fixturing, Test Fixtures, Mechanical Fixtures, Vacuum Fixtures, Jigs
-
Product
Impedance Analysis
S96041B
-
Make impedance analysis measurements of Surface Mount Device (SMD) components on the E5080B vector network analyzer with 16198A-010 10 GHz SMD test fixture.
-
Product
Tool, Adapter, Holding Fixture Adapter AT-1319-29
910121149
Adapter Tool
Used with Raychem holding fixture to aid in the solder process for Mini-Coax Solder sleeve contacts. Both fixture and adapter are included in Solder Kit Part # 910121144.
-
Product
Flash Programming for Functional Test Systems
-
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
Product
Wind Power Solution
NXA SIEMENS
-
The NXA SIEMENS is custom-made with firmware and fixtures designed specifically for Siemens 2.3, 2.4, 2.6, 3.6, and 4.0. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
Product
Power Cord Bending Tester
SW-6
-
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
Test Fixture
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
In-Circuit Test Applications
-
With decades of experience developing test fixtures, we are the recognized industry leaders for solid and reliable quality as well as our outstanding customer service. We fully support our products locally and worldwide for maintenance, repair, and ECO work. Also, 100% wiring verification is part of our Quality Control process, by utilizing automated verification machines for GenRad/Teradyne and HP/Agilent fixture.
-
Product
Calibration
-
General purpose calibration/diagnostic tool.Built in precision resistors.Simple manual contact/routing/resistor selection.4mm terminal posts on key device connections.In line mode to aid fixture wiring/DUT debugging.Comprehensive documentation including circuit schematics.Connecting cables.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
Product
EBIRST 50-pin D-type Verification Fixture
93-005-101
Verification Fixture
The 93-005-101 50-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
PXI 11-Channel 2A Fault Insert Switch
40-202-101
Fault Insertion Unit
This is the 11 Channel version of the 40-202 Fault Insertion Switch. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
Adhesion and Peel Tester
-
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
Product
Ballistic Test Equipment
-
n 1998, H-S Precision introduced ballistic range equipment and fixtures designed to compliment its line of ballistic test barrels. Equipment is available for pressure and velocity testing, NIJ body armor testing, ballistic armor testing and extreme accuracy testing. We are the leading supplier and producer in the World for the ballistic test barrels. The most well known ammunition companies use H-S barrels for testing the quality and consistency of their ammunition.
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
Becker Transponder Test Fixture
TA-3400
-
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Product
Manual Fixture Kit
230356 – CMK-07
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Dual Zipcord Fiber Buffer Thermal Stripper - TFS-900
-
Shanghai Fibretool Technology Co.,Ltd.
TFS-900 900um buffer thermal stripper design small, lightweight, easy to use and reliable, longitudinal peel, peel force is small, the high quality of stripped fiber; blade durable and easy to replace, using linear bearing guide and thermal stripping to ensure no damage to the fiber, easy to strip coating, stripping speed and other characteristics. With the fixture using the strip dual core optical fiber
-
Product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
PXI 12x8 RF Matrix 300MHz 50 SMB - With Loop-Thru
40-726A-511-L
Matrix Switch Module
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
Medium Kelvin Clip Lead
16089B
Accessory Kit
Measure odd-shaped components that you cannot measure using conventional fixtures
-
Product
S-Beam Static Load Cells
2519 Series
-
The 2519-xxxN Series load cells are specifically designed for use with 3300 single column testing systems. Automatic transducer recognition and electrical calibration makes them easy to use. The load cells incorporate overload protection and can withstand loads up to 150% of their force capacity without damage and 300% without mechanical failure. The load cells allow the user to zero out the tare weight of a grip or fixture that weighs up to 40% of the force capacity, while still maintaining the full specified accuracy.
-
Product
Fixtures For Testing
-
Columbia offers a wide range of different fixtures and test equipment that are possible to modify according to your needs of testing. Our range of different types of test fixtures goes from ICT, RF, General Purpose, CMP to CMK.
-
Product
Test Fixtures & Test Sets
-
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
Product
CAM/TRAC Test Kits
-
The Camtrac (registered trademark) series test fixtures provides ‘Z’ axis motion that reduces probe side loading typically seen with Clamshell type test fixtures. This not only extend the life of the probes, but additionally, provide better probing accuracy, especially on fine pitch test centers. Camtrac fixtures are available with the most widely used interfaces in the test industry.
