Showing results: 736 - 750 of 1389 items found.
-
ABB Ltd.
ABB provides optimized and cost-effective solutions for emission monitoring, process gas analysis, cement plant and marine applications as complete turn-key measuring systems:
-
FMD 09 -
IMR Environmental Equipment, Inc.
The continuous measurement of velocity and temperature of gas flows is much important at operation of a system with flowing gases (e.g. hall outlet air, exhaust etc.).
-
EXPEC-2000 -
Focused Photonics Inc.
EXPEC-2000 VOC system is based on the principle of gas chromatography technology(GC-FID),it is of capable monitoring characteristic factors such as methane/non-methane hydrocarbons and benzene etc.
-
ZRS-4H -
Lisun Electronics Inc.
• Test Gas Source: Gas or Liquefied Petroleum Gas (Suggestion: Use good quality gas if possible) • Burner inner diameter: ¢9.5±0.5mm, about 100mm long with air adjusting hole • Height of flame: Can be adjusted from 20 mm to 100 mm according to the standard requirement • Applying time of flame: Burning time can be adjusted from 0 to 99 minutes 99 seconds • Test process: Automatic control • Inner volume: 0.05m³ • Material: Stainless steel or iron plate spray • Power: AC 220V; 50Hz/5A
-
Walsn Enterprises Ltd.
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6~50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
-
FLIR GFx320 -
Teledyne FLIR
The FLIR GFx320 represents ground-breaking technology for visualizing fugitive hydrocarbon leaks at natural gas well sites, off-shore platforms, liquid natural gas terminals, and more. Its certifications for use in hazardous locations allow surveyors to work confidently while maintaining safety. FLIR designed the GFx320 with the user in mind, offering ergonomic features such as the articulating LCD screen to help you avoid fatigue during all-day surveys.
-
BME680 (Qwiic) -
SparkFun Electronics
The SparkFun BME680 Environmental Sensor is a breakout that combines a gas sensor with temperature, humidity and barometric pressure sensing for a complete environmental sensor in a single package. The gas sensor on the BME680 can detect a wide variety of volatile organic compounds (or VOC for short) to monitor indoor air quality. Combine that with precise temperature, humidity, and barometric pressure and the BME680 can work as a completely standalone environmental sensor all in a 1in. x 1in. breakout!
-
ASGU-370 Series -
HORIBA, Ltd.
The multi point calibration units ASGU-370 series is designed for simultaneous (parallel) or step by step (serial) checking of gas analyzers. It is primarily installed in laboratories for quality assurance and is also used for the production of gas analyzers.Furthermore are the calibration units as a Transfer standard in portable suitcase available. Here we have for ongoing quality control in field the versions all in one aluminum suitcase and for a flexible and back-friendly wearing comfort the ASGU-370TS SPLIT.
-
APMC-370 -
HORIBA, Ltd.
Dilution of gases with high accuracy and precision requires high quality MFC’s, especially for high dilution ratios and ranges. Consequently HORIBA’s APMC-370 is equipped with digital MFC’s. These MFC’s are factory calibrated, optional also with a special Polynomial Calibration. HORIBA Europe‘s APMC-370 is designed to calibrate gas analyzers manually, remotely controlled or automatically. It is installed in air pollution monitoring stations for quality assurance in the laboratory and also in the production of gas analyzers.
-
WIKA Alexander Wiegand SE & Co. KG
Filling and handling equipment for SF6 gas are the central tools for the maintenance of gas-insulated equipment. For both installation and maintenance, WIKA supplies the complete product spectrum of efficient service equipment, starting from simple filling carts up to complex, fully automated all-in-one solutions. Furthermore, the instruments support the plant operator with the recording of the SF6 gas volumes and emissions, as is prescribed in the F-gas regulation (EU), No. 517/2014, for specified equipment.
-
8666 -
TEGAM Inc.
The specially designed, shielded tip of this probes makes it ideal for monitoring moving air or gas temperatures. The exposed sensing element, located on the tip of a 3-3/4" long, 1/4" diameter, sheath, is protected by a perforated shield to minimize fluctuating readings caused by radiation or isolated gas pockets. The cord is an extendable / retractable coil-type which is 1-1/2 feet long and can extend up to 3 feet maximum.
-
Ion Science, Ltd.
High-performance sampling disc pumps for next-generation gas detection Silent, compact micropumps with unrivaled features, enabling cutting-edge innovation across environmental and industrial sectors.
-
HR4000 -
Ocean Optics, Inc.
Our next-generation high-resolution spectrometer is a novel combination of optics and electronics that is ideal for applications such as characterizing lasers, measuring gas absorbance, and determining atomic emission lines.
-
InfraTec GmbH
Dual, triple, quad and eight channel infrared detectors for gas analysis and flame detection sensors where more than one element or event is to be detected.
-
VIS -
ABB Ltd.
VIS is a high-performing yet compact multiphase flowmeter, tailored for wet gas applications and able to provide outstanding accuracy also in the most challenging operating regions.