Showing results: 7366 - 7380 of 8141 items found.
-
TW / CW series -
Clima Temperatur Systeme
Walk or drive-in temperature and climatic test chambers can be designed from CTS by a standardized grid system affordable in all sizes. The refrigeration performance data are adjusted here by our experienced sales and project engineers on your testing out. The walk / drive-chambers are ideal for larger components and finished products. CTS as a medium sized company attaches great importance to the detail quality of the equipment components, with only the best supplier products such as compressor and solenoid valves are used. Your resulting advantages are trouble-free long-term operation and thus no loss of valuable test time.
-
Valiant 153M -
Safran Federal Systems
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
GX5733 -
Terotest Systems Ltd.
The GX5733 is a 3U modular digital I/O card that offers up to 128 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5733 offers the highest channel density and flexibility in the industry for a single slot, 3U PXI plug-in board. 96 channels support TTL levels and an additional 32 I/O channels can be customized by installing one of Marvin Test Solutions' GX57xx series I/O modules. Alternatively, the remaining port can be configured to support 32 TTL channels.
-
LD-LIMA-A10 -
Labodam
Infrared Moisture AnalyzerLD-LIMA-A10is an online, fast, continuous measurement and non-contact measurement device with measurement distance range of 20 to 40 cm. It provides automated control and 4 to 20 mA current signal. This IR Moisture Analyzer emits different wavelengths of infrared light (4, 6, 8, 10 beam) to calculate the moisture content of the measured object. Designed with long-life high-speed brushless motor, imported high response infrared sensors, information processing chip FPGA + DSP + ARM9 combination, to attain real time data, improved stability and precision.
-
Noisecom
The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.
-
Amonics Ltd.
Amonics' EDFA range adopts unique design to produce maximum signal gain and saturated output power while maintaining low noise figure, enabling test capabilities in system or component level manufacturing and characterizing processes, as well as facilitating highly demanding R&D applications. The compact turnkey benchtop or 19" rackmount unit incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power control knob and optical connectors. An integrated RS232 computer interface enables easy control, diagnostic functions and data acquisition.
-
microBlox -
Acromag, Inc.
Acromag's microBlox uB Series I/O modules offer a compact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measurement and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
-
NI CompactDAQ -
NI
This NI CompactDAQ configurable data-logging system includes an NI CompactDAQ controller or chassis, C Series I/O modules, and Chameleon software. It is designed for structural test and monitoring applications with the NI CompactDAQ controller, which includes built-in processing and nonvolatile storage for running Chameleon software and logging data locally. Alternatively, you can choose a USB or Ethernet chassis for a lower cost system that requires an external PC. This system accepts a variety of C Series I/O modules, so you can mix and match microphones, accelerometers, and temperature and bridge-based sensors.
-
VS-SECM (DC And AC) -
Ametek Scientific Instruments
The SECM integrates a positioning system, a bipotentiostat, and an ultramicroelectrode probe or tip. The positioning system moves the probe close to the surface of the sample, within the local imaging zone. The bipotentiostat can polarize the probe only (feedback mode) or the sample and the probe independently (generator-collector mode), while measuring the resulting current(s). The probe is specially designed to have a specific tapered polish (per the RG ratio) and active radius below 100 microns. The positioning system scans the probe and charts position with measured electrochemical parameters, creating a data map of local current.
-
North Atlantic Industries
NAI’s family of highly configurable Rugged COTS Systems are ideally suited for defense, commercial aerospace, and industrial applications that require high-density I/O, communications, Ethernet switching, and processing for mission-critical tasks such as communications, guidance, sense and response, data acquisition and motion control. The simplified, modular approach of our Configurable Open Systems Architecture™ (COSA®) enables us to use the same building blocks across multiple platforms and programs, making it possible for you to develop semi-custom solutions quickly, without NRE, while retaining all the benefits of COTS products.
-
ZZ Booster-Transmitter -
ZZ Resistivity Imaging Pty. Ltd.
*3,000W output power in 2 adjustable voltage ranges ( 400V/7.5A, 1,200V/2.5A), the FlashRES booster transmitter is particular useful for surveys in high resistive areas or IP surveys.*When the FlashRES booster transmitter is connected FlashRES-UNIVERSAL, for each current injection, the system could collect 61 voltage measurement, this greatly increases the data collection speed.*Uses two standard 12V batteries connect in series as input power source*The FlashRES booster transmitter is designed for heavy duty usage, the instrument is shock, water and dust proof.*Light-weight and easily mobilised
-
4900 -
BPM Microsystems
The 4900 is powered by the newest BPM 9th generation technology, which delivers the fastest programming speeds in the industry for MCU’s, eMMC HS400, NAND, NOR and Serial Flash devices. BPM 9th generation technology produces 200 MHz signals, allowing each byte of data to transfer in up to 2.5 ns. Up to 9 times faster than competing programmers. 3D Vision option inspects BGA, CSP, QFP, TSOP, SOIC and J-Lead devices for coplanarity, bent lead, pitch, width, diameter, standoff and XY errors.
-
ProDAQ 3020 -
Bustec Ltd.
The ProDAQ 3020 is a C-size, register-based VXIbus module. It provides a direct connection from a PC to a VXIbus mainframe using the high-speed USB 2.0 bus. It plugs directly into the USB port of a PC and supports multiple mainframes interconnected via cables in a tree configuration. With high-speed data acquisition, the ProDAQ 3020 provides a high-performance and cost-effective solution for VXIbus applications. With the optional GPIB port, users can control GPIB devices included in a test system via the USB connection to the PC. The multi-crate trigger chaining provides a connection between the VXIbus trigger lines in a multi-crate system.
-
ProDAQ 8035 -
Bustec Ltd.
The ProDAQ 8035 PCI Express x4 active optical cable is a standard compatible cable for linking crates equipped with the ProDAQ 3026 Low-Cost PCI Express VXIbus slot-0 interface or the ProDAQ 3030 PCI Express VXIbus slot-0 interface to the ProDAQ 3261 PCI Express host interface. The cable transmits the data normally transferred via the copper cable, optically and offers connectivity beyond the maximum cable length of seven meters for copper cables by extending the maximum distance between the host computer and the VXIbus system(s) to 300 meters.
-
VT-96 -
Holding Informtest
Thermal station VT-96 is intended for building data collection systems (distributed and remote) from thermocouple temperature sensors. The interfaces allow you to easily and quickly connect the VT-96 to a remote (via ETHERNET) or nearby computer (via USB). The integrated WEB-page provides a convenient way to check the communication with the unit and its functioning, and the standard VXIplug & play drivers reduce the costs of integrating the unit into the system and developing application software. Multiple thermostats easily integrate and synchronize with each other and other VXI instruments via a dedicated Trigger Bus.
