Showing results: 226 - 240 of 7331 items found.
-
MKS Instruments
The DELTA™ III Flow Ratio Controller divides and controls mixed process gas flows to three chambers or zones within a process chamber at proportions specified by the user to optimize process uniformity and repeatability. Available with EtherCAT® or DeviceNet™ communications, this device provides the latest in gas flow ratio measurement and control technology.
-
MKS Instruments
DELTA™ IV 4-zone Flow Ratio Controller is a digital controlled, browser-enabled, process control instrument providing the latest gas flow ratio measurement and control technology to meet the demands of multi-channel flow distribution for semiconductor, flat panel, and solar panel process uniformity and control. It is available in EtherCAT® or DeviceNet™ providing the latest gas flow ratio measurement and control technology to meet the demands of multi-channel flow distribution.
-
Renesas Electronics Corp.
Renesas offers several delta-sigma and sigma-delta analog-to-digital converters for high resolution measurement applications.
-
VEGA Grieshaber KG
The solid content of a liquid is determined with the help of density measurement.
-
MRC ltd.
The oscillating U-tube densitometer method is a technique to determine the density of liquids and gases based on an electronic measurement of the frequency of oscillation, from which the density value is calculated.Density meters work by measuring the oscillation of a glass tube containing the sample.Specific gravity and refraction index can be measured. They are used in many industries such as: oil, chemical, food and beverage industries for quality control and research and development.
-
D155 -
CANNON
For Measuring Density, Specific Gravity and API DegreesASTM D1250, ASTM D1298, ASTM D4052, ASTM D7777. The automated CANNON D155 offers a low-cost, affordable alternative to manual hydrometer methods for measuring density and specific gravity with easy, one button operation. Built-in thermal control provides quick, precise measurement with 4 decimal resolution.
-
AMETEK Drexelbrook
This reliable level transmitter is specially designed to maximize the throughput of oil/water separators and accurately measures the electrical interface in the emulsion even in upset conditions. This measurement is critical because the separation vessel operates at maximum efficiency when the electrostatic grid is close as possible to the interface.
-
Edmund Optics Inc.
Detectors are used to measure the illumination of a light source for a number of optical or spectrometry applications. Detectors consist of arrays of photodiodes or photodetectors that transmit electrical current when excited by collision from photons. Detectors enable the measurement of important light characteristics that are not conveniently acquired in other ways. A selection of photodiodes is also available with linked amplifier capabilities for easier, more precise measurement capacities.Detectors
-
Vogelsang & Benning
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
Keysight Technologies
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
NOVOTEST KTR-1 -
NovoTest
Dew Point Meter NOVOTEST KTR-1 is designed for rapid non-destructive measurement the temperature, humidity, dew point calculation and measurement of the surface temperature by contact method.
-
AMETEK Sensors, Test & Calibration
The DFX II Series is a low cost digital force gauge, ideal for applications where the user is interested in basic peak force measurement. This digital force gauge is available in 10 lbf, 50 lbf, 100 lbf and 200 lbf. Loads are displayed in ozf, gf, lbf, kgf, and N units and can be set up to display data in a range of languages.
-
NI
DIAdem is software specifically designed to help engineers and scientists quickly locate, inspect, analyze, and report on measurement data using one software tool.
-
FTM-1 – UKAS -
Rhopoint Metrology Ltd
Baty dial thickness gauges are direct reading instruments for quick and accuratemeasurement of rod, strip or sheet material, such as paper. All standard instruments aresupplied with 10mm (0.39″) diameter at contacts. The well balanced frame andhandgrip make these thickness gauges very easy to use for the measurement of sheet easy to use for the measurement of sheet materials.The lifting lever and springloaded spindle ensures controlled contact pressure on the sample.
-
Mountz Inc.
A dial torque wrench is an essential tool in torque measurement, as it provides quality control in regards to monitoring and verifying torque. This tool is commonly used to test, audit, and verify torque applied to joints. Using the memory pointer, the dial torque wrench will capture finishing torque that is applied to any fastener.