Showing results: 8041 - 8055 of 8144 items found.
-
Automator Manual Family -
Test Electronics
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
DITH 120 -
Desco
Infrared Thermometer is also known as laser thermometerInfrared thermometer is a thermometer which infers temperature from a portion of the thermal radiation sometimes called blackbody radiation emitted by the object being measured.Laser is used to help aim the thermometer or non-contact thermometers or temperature guns, to describe the device's ability to measure temperature from a distance. By knowing the amount of infrared energy emitted by the object and its emissivity, the object's temperature can often be determined. Infrared thermometers are a subset of devices known as "thermal radiation thermometers".The design essentially consists of a lens to focus the infrared thermal radiation on to a detector, which converts the radiant power to an electrical signal that can be displayed in units of temperature after being compensated for ambient temperature. This permits temperature measurement from a distance without contact with the object to be measured. A non-contact infrared thermometer is useful for measuring temperature under circumstances where thermocouples or other probe-type sensors cannot be used or do not produce accurate data for a variety of reasons.
-
SEN-36002 -
Playing With Fusion Inc
SEN-36002 is a highly integrated carrier board designed for the Si1145 UV, Ambient Light and Proximity sensor IC from Silicon Labs. This sensor has 100mLUX resolution, and has a dynamic range of 1 LUX to 128 kLUX with IR correction. This means that whether your application is indoors in poor lighting conditions or outside in full sunlight, this sensor has you covered. In addition, we added a high power LED (150mA max, 20 degree) to take full advantage of the proximity sensing capability of this IC - something you won't see on most competitive carrier boards. Integration is easy with 4 x 4-40 sized mounting holes at the corners of the PCB and signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. The INT pin is also broken out for interrupt capability.
-
SilverBack Series -
Multidyne
We all appreciate the dramatic flair of cinematic video. Creating high-resolution broadcast content with cinematic quality has historically been a tall order, from cost of entry barriers to workflow integration. MultiDyne developed its SilverBack Series to help content producers convert digital cinema cameras into SMPTE studio cameras for live multi-camera production. SilverBack fiber camera adapters are lightweight “cameraback” systems ideal for live concerts, sports, TV productions and worship services. There are several models to meet varied budgets, all vendor-agnostic and engineered to adapt the user’s camera of choice. SilverBack systems offer modular designs to support diverse I/O configurations, with all signals carried over a single tactical or hybrid fiber cable. Hybrid and tactical fiber conversion as well as remote powering through MultiDyne JUICE portable power supplies further empower mobility for camera operators.
-
Air Brake NanoLeak Finder -
Redline Detection, LLC
“The Air Brake NanoLeak Finder™ allows technicians, for the first time ever, to test for air brake leaks and pinpoint the precise location of leaks, in minutes. The equipment is being used by OEMs to locate leaks in heavy duty trucks and equipment that would take hours with conventional methods, saving valuable service time and getting trucks back on the road fast” said Alex Parker, Executive Vice President of Redline Detection “this is a very exciting breakthrough for anyone who deals with air brake leaks.” The patent pending technology in the machine creates a signature vapor that, in conjunction with the hand-held NanoLeak™ Locator, pinpoints the precise location of air brake leaks instantly. Clear, audible and visual signals speed diagnostics and pinpointing of leaks. The equipment improves efficiency, saving valuable hours and marking a dramatic technical advance from conventional, messy, soapy water methods and ineffective listening devices.
-
Omni-λi -
ZOLIX
Zolix Imaging Spectrometer includes different focal length 320mm, 500mm, 750mm; ◆Manual micrometer adjustable slits for precision control of incoming light. Motorized Slit and fixed slit is optional. • More than 100 gratings for the best spectral range, throughput and dispersion to meet your application◆DSP controlled stepping motor scanning system provides superior precision and repeatability of wavelength positioning◆Optional internal shutter or six-position filter wheel for experiments requiring background removal or signal attenuation◆Installation and set-up through USB 2.0 computer interfaces • Stand-alone Omni Series monochromator control software for basic scanning and calibration. Also includes utilities for grating updates and communications◆ Active X control support Visual Basic, C++ and Delphi drivers allow users to design their own acquisition programs◆ZolixScan data acquisition software provides a simple user interface for easy data acquisition and experimental set-up
-
Test Chest 3G (Multi Function Test) -
Murraypro Electronics
Quick and very easy to use, the amazing Test Chest boasts instantaneous Audio + Video generation and Monitoring. NO tedious boot-up means Test Chest is “First out of the blocks” every time by 10s of seconds, and it’s intuitive touch-screen speeds Engineers to the required function, saving precious time and giving their investigations a real head start. 10bit precision signal generation is standard with Test Chest, as are the analysis utilities which are displayed on it’s superb 5” high resolution touch screen Monitor screen, and stereo sound too (when present).Ease of use and protection whilst in service are serious matters, so Test Chest is fitted with ‘Ez-Grip’ resillent rubber end sleeves; these assist grip, and provide additional protection against everyday knocks and bumps. During transportation your Test Chest’s tough extruded alloy housing is cradled within a customised go-anywhere foam lined ABS Carry-case for complete protection.
-
S-101 -
Notice
LD Driver slot module of FOTS system is an efficient module that is user centered, which can drive various kinds of laser diode for the use of optical signal transmission or light source. The module has a built in LD socket, in which LD of 14 pin butterfly type is installed, which makes it possible for the user to change the LD he or she wants to drive when needed. It is leaded to get rid of the inefficiency of expense, at which various types of expensive united source module needed are purchased. By operating monitoring PD and high-performance processor that are installed inside the module, the output power and temperature of LD can be driven accurately and stably. The laser diodes can be modulated internally in square, sinusoidal, and triangular waves and its output power and temperature can also be maintained the level set by the user. In order to realize the various functions, the efficient and multi-functioned control programs with high speed processor, LCD monitor or GUI for remote control are available.
-
Model 7641 -
Jinan Testing Equipment IE Corporation
These COD gages use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7641 is ideal for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. All units can be displaced slightly in compression for ease of installation. The COD gage is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the COD gage. This system provides a number of functional enhancements, including: high speed digital output, built in calibration and tare functions, analog and digital filters, and more. The 7641 is readily interfaced with most existing test controllers, and may be directly connected to a data acquisition system or chart recorder, or directly to a PC. The 7641 may be used for strain controlled tests such as JIC.
-
BEQ II.1 -
HEAD acoustics GmbH
*Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.
-
IMB501 -
Axiomtek Co., Ltd.
The IMB501 is powered by the LGA1151 socket 7th/6th generation Intel® Core™ i7/i5/i3, Pentium® & Celeron® processors with Intel® H110 chipset. The IMB501 utilizes two high bandwidth 288-pin DDR4-2400/2133/1866 with system memory up to 32GB to meet the needs for high memory capacity and high data transfer speed. The upcoming industrial-grade ATX motherboard offers long-term support and upgradeability that can ensure the best performance and lifespan for its extended industrial computer system. To allow flexible and rapid development of custom functions, the industrial-grade ATX motherboard comes with rich expansion options including one PCIe x16 slot, two PCIe x4 slots (only support x1 signal), four PCI slots, and one PCI Express Mini Card slot. The ATX mainboard is suitable for industrial automation, factory automation, advanced communication, gaming, entertainment, POS/kiosk, surveillance, medical, just to name a few.
-
PICO312 -
Axiomtek Co., Ltd.
The PICO312 is a palm-sized fanless pico-ITX motherboard built with the latest 14 nm Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake SoC). One 204-pin DDR3L-1867 SO-DIMM socket supports system memory up to 8GB. The tiny 2.5” pico-ITX embedded board features Intel® Gen9 graphics engine bringing a true high definition visual experience with dual display configurations through one LVDS and HDMI. In addition, it was designed for special needs of fanless operation under temperature from -20°C to +70°C. The PICO312 features a full-sized PCI Express Mini Card slot in support of mSATA and a pair of expansion connectors with additional signals including one PCIe x1 lane, one LPC, one DDI, four USB 3.0 ports, one SMBus and one HD audio, giving this SBC high expandability to meet all requirements.
-
Eltima Software
The main goal of Virtual Serial Port Driver by Eltima Software is creating virtual COM port pairs. Virtual serial ports created in VSPD behave as if they were real ports and are taken for the real ones with the serial applications. Via these ports serial applications can communicate with each other and transfer data via virtual null-modem cable. The data written to one virtual serial port can be instantly read from the other. Virtual serial ports created in VSPD support all serial port settings, strict baudrate emulation, HandFlow control and signal lines. After virtual COM port pair was created, one can see these ports in Device manager, moreover these ports are available automatically at system startup, even prior to logon. Virtual Serial Port Driver is available in a GUI version as well as a driver version with API for those who are going to use it in their own product.
-
44550 -
M. C. Miller Company
No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)
-
GX3700e -
Marvin Test Solutions, Inc.
The GX3700e is a user configurable, FPGA–based, 3U PXI Express card offering 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3700e is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded directly into the FPGA or via an on-board EEPROM.
