Showing results: 7246 - 7260 of 8144 items found.
-
UV-260 -
Sonel S.A.
Being with high sensitivity UV-260 is a power tool to detect UV emission in full daylight with high signals from faraway and nearby sources. UV-260 is an ideal predictive maintenance device for overhead transmission lines and high voltage substations. UV-260 is newest genaration of UV imaging system with an emphasis on high performance functionality and easy operation, it is widely used in transmission line inspection, electrical utilities, HV research institutes, HV electrical component inspection, HV panal inspection, service providers, laboratories and more.
-
#8026 -
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
ERAVANT
Probe antennas are offered as both standard and custom models with a rectangular waveguide interface. Probe antennas can only support linear polarization. These antennas are often used to measure the gain of other antennas by comparing the signal levels of the probe antenna and antenna under testing. The standard models operate across the full waveguide band and offer 6.5 dB nominal gain and 115 and 60 degrees half power beamwidth at center frequency. The below standard offering covers the frequency range of 8.2 to 170 GHz.
-
Hydrotechnik UK Ltd
Our comprehensive range of hydraulic pressure testing equipment is of the highest quality and makes hydraulic testing much easier and extremely accurate. 75mm digital pressure gauges with 0.5% accuracy up to 600 bar. Numerical & 0-100% bar graph display. Min/max storage. 2 x AA batteries. Stylish pressure switch / gauge up to 700 bar with two settable switch values. 4-20mA output. 15...30Vdc external power required. LED high speed panel mounting displays for frequency or analogue signals.
-
TDEMI S series -
Gauss Instruments
The new Real-time Spectrum and Signal Analyzer TDEMI S from GAUSS INSTRUMENTS is the new benchmark for real-time, communication and EMC testing. It is thoroughly flexible in its configurability and extensibility. In its basic configuration, the TDEMI S is a high-performance spectrum analyzer and is available in frequency ranges up to 1, 6, 9, 18, 26, 40, 44 and 50 GHz. It can be extended by external mixers up to the Terahertz frequency range. Due to its compact design and a 12V output, it is a great tool for field testing or on-board testing applications.
-
9107A -
Innovative Products of America
The #9107 Electric Brake Force Meter with Dynamic Load Simulation and Circuit Testing (patents pending) is designed for use on 7-spade equipped vehicles. This new technology automatically recognizes the electronic signature of both Integrated (ITBC) and aftermarket Trailer Brake Controllers, simulates trailer load and displays real-time, brake-controller output gain and application time. It can quickly troubleshoot truck-side tow circuits, e.g., tail lights, turn signals, 12V+, reverse and ground condition and the 25 ft. cable allows for one-man, in-cab testing.
-
2200 -
Photon Kinetics
The 2200 Optical Fiber Analysis System provide high-speed characterization of the spectral loss of single-mode and multimode fibers. Configurations include the 2200 for single-mode fibers, the 2210 for both single-mode and multimode fibers, and the 2220 designed for single-mode fiber ribbons. All three systems employ unique fiber preparation and signal processing techniques, which deliver both the measurement performance and the testing throughput required by high volume fiber, cable and component manufacturers. Options are available for mode field diameter and multimode numerical aperture measurements.
-
SS series -
Ono Sokki
The SS series torque detector suits to wide variety of torque measurement application, including performance test of motors, pumps, compressors, blowers, turbines and gears. High rigidity results from the unitized cast-casing structure and SS series torque detector can be handled easily as being free from parts replacement on treatment of maintenance, comparing to other type of torque detector such as strain gauges, with non contact signal detection on the detector. 13 models in the series can be provided and chosen among them according to requirement in torque capacity.
-
Analog Devices Inc.
Analog Devices’ ADE energy measurement ICs address the challenges of next-generation smart meter architectures and are ideal for measuring active energy (kWh), apparent energy (kVA), reactive energy (kVAR), rms, and power quality with the highest accuracy in single phase and polyphase revenue meters, industrial instruments, and energy monitoring applications. ADI’s ADE energy measurement ICs combine analog-to-digital converters with fixed-function digital signal processors to perform critical measurements, while providing unparalleled functionality and ease of use.
-
DR068-M1 -
Teledyne Defence & Space
Teledyne Defence & Space (TDS) DR068-M1 Digitising Receiver combines a state of the art broadband frequency measurement receiver with a high dynamic range successive detection log video amplifier to realise a high probability of intercept receiver. Digital signal processing techniques are utitlised to derive pulse parameters which are packaged into a PDW and transferred via a low latency Gigabit Ethernet interface. The DR068-M1 enables new and existing systems to incorporate a wideband high POI pulse detection capability with minimal integrating effort.
-
Smiths Interconnect
Our fixed and mobile positioning systems featuring TECOM technology are used in range telemetry, flight termination, airborne and ground datalink, target tracking and jamming, signal intelligence, and direction finding applications. Positioning systems range from man-portable to 7 meter installations. Both positioning/controlling systems and turnkey solutions are available with reflector and feed assemblies reaching 0.5 to 325 GHz. With all positioners designed to meet environmental MIL-STD requirements, developing complete solutions for harsh conditions has become one of our core capabilities.
-
PK-3456 Spy Splitpair -
Pansco, Ltd
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
Silicon Turnkey Solution, Inc.
High-speed devices create significant challenges for functional testing, for example, the need for high-bandwidth interfacing to maintain signal integrity at multi-gigabits per second data rates and the ability to measure high-speed bit error rate and jitter. STS brings extensive experience in high-speed functional testing for commercial, military and aerospace devices to meet the most stringent customer requirements. Our highly integrated testing laboratory and efficient workflow are designed with one goal in mind: to shorten time-to-market and enhance our customers’ ability to compete.
-
QuickSun® 550CE -
Endeas Oy
QuickSun 550CE is certified by TÜV Rheinland and a detailed test report is included with every simulator proving Class A+A+A+ performance with respect to spectrum, irradiance non-uniformity and short term instability (STI). Long term instability (LTI) is also within Class A+ tolerances during the 40 ms long flash pulse. IV characteristics are recorded with an electronic load and proprietary electronics unit which measures voltage, current and irradiance signals when module is swept e.g. from short circuit to open circuit or vice versa.
-
Mensor Corp.
Precision pressure transducers convert pressure into an analog or digital signal proportional to the pressure being sensed. Precision pressure transducers (sometimes called transmitters) are used to monitor and or control sensitive pressure processes. They can also be used as high accuracy transfer standards or as a factory working standard for testing or calibrating a variety of pressure measuring instruments. With an accuracy as high as 0.008 % of reading, these pressure transducers can be found in laboratories or in production environments where a high degree of precision and accuracy are required. Each transducer is calibrated in Mensor's 17025, A2LA certified laboratory.
