Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
4 Digit Angle Position Indicator (API)
TA-900
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-01
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.25 GS/s on 4 Channels, 1.5 GHz Bandwidth
M4I.2234-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXI 2 Amp MUX, Single 32-Channel 1-Pole
40-635-101
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Electrical Clock Recovery
N1076B
The N1076B Electrical Clock Recovery provides standards-compliant clock recovery capability on electrical NRZ and PAM4 signals from 125 MBd up to 64 GBd
-
product
LXI Microwave Multiplexer, SP4T, 10-Bank, 50GHz, 50Ω, SMA-2.4
60-803-610
Our 60-803-610 is a 10 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI 50Ω 6:1 Microwave Multiplexer 4-bank 18GHz SMA
60-800-004
High performance RF multiplexer suitable for switching microwave signals
-
product
Versatile 5-Channel Industrial Amplifier/ Conditioner Instrument
MODEL TIO-3000
The TIO-3000 System was originally designed to perform precision summing on 2, 3 , or 4 load cell signals for weighing applications. Development has progressed into accessory modules with considerable versatility for user defined configurations in a compact economical five (5) slot system with built-in meter and channel selector. Please see below for more information on the four available plug in modules and for available system configurations.
-
product
BNC-2110, 68-Pin SCSI to Female BNC and Spring Terminal, DIN Rail, Desktop Mount, Shielded Terminal Block
777643-01
68-Pin SCSI to Female BNC and Spring Terminal, DIN Rail, Desktop Mount, Shielded Terminal Block - The BNC-2110 can be used with various NI multifunction I/O and analog output devices. The BNC-2110 simplifies the connection of analog signals, some digital signals, and two … user-defined connections to the data acquisition device while maintaining the integrity of your measurements with a shielded enclosure. It includes a DIN Rail and a desktop mount option.
-
product
Dual-Axis Accelerometer For HS3/4/4-DIFF Handyscopes, +/- 5G
TP-ACC50-25
The Accelerometer is a low cost, low power, complete dual-axis accelerometer with signal conditioned voltage outputs. The output signals are analog voltage proportional to acceleration. The Accelerometer is capable of measuring both positive and negative accelerations to at least �+/- 5G.
-
product
Receivers
SDR receivers (Software Defined Radio) perform all signal processing in software, offering multi-standard support, access to all data in the channel, and advanced RF measurements.DekTec's other receivers are based on standard demodulator chips and therefore do not take cycles from the host CPU. These can be used if the SDR features are not required.
-
product
Measurement System for ESD Protection
SampleProtect
The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capa...show more -
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix topology With Column Protection Resistors
782385-04
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Oscilloscope: 200 MHz, 4 Analog Channels
DSOX2024A
200 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
product
LXI High Density 128x8, 2A Matrix with BIRST
60-550-022
High-density single pole matrix module capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2230-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXI 10 Banks of 8 Channel 2 Pole MUX
40-615-022-10/8/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Distributed Motion Control
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).The modules convert input/output signals to engineering units and transmit/receive, in ASCII format, to/from any host computer with an RS-232 or RS-485 port. NuDAM modules are the key components in flexible and cost effective remote data acquisition and control systems.
-
product
Signal Conditioning and Filtering
MSXB 065
The MSXB 065 Signal Conditioning Expansion Board provides filtered analog signal conditioning for voltage signals for Data Acquisition Processor systems. Each board has differential inputs; jumper-selectable simultaneous sampling; jumper-selectable gains of 1, 5, and 25; fourth-order anti-alias filters, cutoff frequencies from 100 Hz to 50 kHz.
-
product
Single-Channel 12-Bit, 1 GSPS Digitizer
ADQ30
ADQ30 offers a single-channel configuration with 1 GSPS sampling rate. The programmable DC-offset makes it ideal for sampling unipolar signals.
-
product
Digital Audio Snake System
OmniSnake
The OmniSnake consists of a Stage Box that converts microphone/line-level analog inputs to a multiplexed digital signal, and a companion Base Unit that de-multiplexes to provide individual outputs. Digitizing the analog audio at the source eliminates the potential for ground loops, noise interference and crosstalk. Each Stage Box has 8 inputs, and two Stage Boxes can be linked together via coax to form a combined 16 channels, which is carried over coaxial cable to the Base Unit.
-
product
PCI Express-to-XMC Adapter
4876
The Technobox, Inc. P/N 4876 PCI Express-to-XMC Adapter is a development/diagnostics tool that permits the testing of a PCIe card in an XMC site. Up to 8 lanes are supported via the P15 connector. Several activity LEDs located at the edge of the board give an indication of key XMC and PCI Express signals and voltages.
-
product
SMA Male to SMA Male Cable, 50 Ohm, 1 m
781845-01
The SMA-SMA Coaxial Cable, sometimes referred to as SMA100, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths, this one is 1m.
-
product
AC / DC Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
For the separation and conversion of sinusoidal and non-sinusoidal alternating currents and voltages into standard signals. TRMS Education / True-RMS. Calibrated switchable versions with Weitbereichsnetzeil and high working voltage up to 3600 V AC / DC.
-
product
Differential Voltage Probes
DP150/DP200pro
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, var...show more -
product
Video Signal Distributor
MSDS-4416
MSDS-4416 distribute four TMDS input signal up to four display devices such as Projector, PDP, HDTV and TFT-LCD without diminution and distortion. The distribution support single/dual 8~16 bit and user can select input signal by press button and make sure being connected input source with led of the front panel.
-
product
Low Cost Microwave Wideband Electro-absorption DFB Transmitter (without RF Amp)
MT60 (40KHz~33GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT60 series microwave DML optical transmitter, are able to transmit 33G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely appl...show more -
product
Signal & Spectrum Analyzers
The Rohde & Schwarz signal and spectrum analyzer portfolio offers options ranging from low-cost, yet powerful 1 GHz analyzers to handheld and mid-range models to full-featured 85 GHz spectrum analyzers. Designed by the RF experts at Rohde & Schwarz, all spectrum analyzers feature exceptional signal integrity, high value and excellent reliability.
-
product
AC Electronic Load
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
product
PXI 2A Multiplexer, 16-Bank, 8-Channel 1-Pole
40-614-001
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
