Showing results: 4981 - 4995 of 8144 items found.
-
Video Products Inc
Video Test Pattern Generator, Portable Monitor Tester, Test Video Audio Signals, HDMI, DVI, SDI, Component Video, HDCP
-
Advantech Co. Ltd.
Advantech's industrial media converters can convert Ethernet data and power into fiber optic signals. They also offer Link Fault Pass-Through (LFPT).
-
Power Meter -
ZETLAB Company
Power Meter is used for determining the power of the electrical current coming to the input channels of ADC modules and FFT spectrum analyzers, or that of the electromagnetic signal.
-
Spark P3 -
Manta Test Systems
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
40-517-002 -
Pickering Interfaces Ltd.
The 40-515/516/517 2 Amp, 2-Pole Matrix Modules form part of the System 40 PXI ProgrammableSwitching system. Each module consists of a matrix of 64 2-pole electro-mechanicalrelays under the control of a PXI/PCI interface.These modules are designed for switching medium voltage/power signals in test applicationswhere reed relays do not have sufficient rating. They are also suitable for telecomsapplications where send and return signals need to be switched simultaneously.
-
Qosmotec Software Solutions GmbH
The Qosmotec handover test system QPER is a versatile test platform for emulating the RF signal between radio devices in a wireless network, e.g., between mobile stations and radio infrastructure of a mobile network. It is employed in test beds where radio signals are transmitted through coaxial cables and specifically manipulated by testers. QPER can be based on various hardware platforms, from attenuator arrays to digital channel emulators.
-
40-516-002 -
Pickering Interfaces Ltd.
The 40-515/516/517 2 Amp, 2-Pole Matrix Modules form part of the System 40 PXI ProgrammableSwitching system. Each module consists of a matrix of 64 2-pole electro-mechanicalrelays under the control of a PXI/PCI interface.These modules are designed for switching medium voltage/power signals in test applicationswhere reed relays do not have sufficient rating. They are also suitable for telecomsapplications where send and return signals need to be switched simultaneously.
-
FuturePlus Systems
The DDR3 DIMM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR3 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR3signals for convenient analog probing. The user can then easily observe both the digital and analog representation of the DDR3 Address, Command and Control bus. Solder down N5381B analog probes purchased separately from Keysight Technologies.
-
BK2110 -
BaKo Co., Ltd
The BaKo BK2110 Audio Analyzer is a 2 channel Digital Signal Processing (DSP) based system so you can analyze a stereo signal from an acoustic device. And because it is DSP based, it can quickly and accurately test high quality digital audio devices. All test items can be measured simultaneously and you can see them in real time or, using the LAN interface, send them to a computer system to analyze.
-
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
-
5047 -
Abaco Systems Inc
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
40-515-002 -
Pickering Interfaces Ltd.
The 40-515/516/517 2 Amp, 2-Pole Matrix Modules form part of the System 40 PXI ProgrammableSwitching system. Each module consists of a matrix of 64 2-pole electro-mechanicalrelays under the control of a PXI/PCI interface.These modules are designed for switching medium voltage/power signals in test applicationswhere reed relays do not have sufficient rating. They are also suitable for telecomsapplications where send and return signals need to be switched simultaneously.
-
FBC -
Farran Technology Ltd
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
M1971E -
Keysight Technologies
Keysight M1971E 55/60 to 90 GHz waveguide harmonic mixers is an un-preselected mixer provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Smart features are embedded to help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
M1971W -
Keysight Technologies
Keysight M1971W 75 to 110 GHz waveguide harmonic mixer is an un-preselected mixer that provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Embedded smart features help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.