Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
2-28 Vrms Input, 2-115 Vrms Exc, 47 Hz - 1 kHz Freq
SDx
Synchros and Resolvers are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Resolver-to-Digital or a Synchro-to-Digital converter is used to convert these signals to a digital output corresponding to the shaft angle and/or velocity.
-
product
Lightning Surge Generator
CDN-5810
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-5810 signal line/data line coupling decoupling network, unshielded symmetrical communication line suitable for surge pulses and ringing wave pulses, designed according to Figure 10 of the new standard IEC61000-4-5.Ed3. It also satisfies ringing Figure 10 requirements of wave standard IEC61000-4-12.Ed2. According to the characteristics of the line, the pulse coupling can be realized by gas discharge tube, capacitor, diode and other different methods.
-
product
Audio Generator
AG-51
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and le...show more -
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified...show more -
product
Accelerometers - Special Purpose
Analog Devices accelerometers and iSensor® MEMS accelerometer subsystems provide accurate detection while measuring acceleration, tilt, shock, and vibration in performance driven application. Our portfolio leads the industry in power, noise, bandwidth, and temperature specifications, and offers a range of MEMS sensor and signal conditioning integration on chip. Our MEMS-based Circuits from the Lab® reference designs have been built and tested by ADI experts to help you jumpstart your next system design.
-
product
Thermometer Hygrometer Barometer
H7531-4
Sensor H7531 is designed for online monitoring of temperature, relative humidity of air without aggressive substances. Three binary inputs to detection of two-states signals are the advantage. Other devices are controlled by two relay outputs.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
Signal Conditioner
SGA
Versatile signal conditioner featuring user selectable outputs of +/-10V, +/-5V, 0-10V, 0-5V, 0-20mA and 4-20ma. DC or AC powered with switch selectable filters from 1 to 5kHz and a sealed ABS enclosure. Supports shunt calibration and a wide range of gain settings.
-
product
Ethernet-GPIB-USB to Serial Interface
Model 9006
* All interfaces provide full communication with the serial device.* Ethernet port supports VXI-11 and raw socket protocols.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* GPIB port is IEEE-488.2 compatible.* USB port uses Microsoft supplied driver to prevent driver problems with operating system change problems.* Serial port provides RS-232 and 2 or 4-wire RS-48...show more -
product
Twelve-channel Cable/terrestrial Receiver For PCIe
DTA-2139B
Twelve (!) receivers on a single card, supporting any mix of cable (DVB-C, QAM-B/C) and terrestrial (DVB-T, DVB-T2, even ISDB-T) signals. All twelve transport streams are demodulated simultaneously, allowing you to monitor a complete network in real time.
-
product
Blank Module, Receiver/ITA, 1 Module Position, 90 Series Modules
510104118
Blank modules are for unused module slots. The blank shielding module fills a module slot and shields signals between the modules. Blank modules fit in either ITA or receiver positions.
-
product
PXIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4X.4470-X4
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
product
Digital Wideband Transceiver Analysis
S94610B
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver typ...show more -
product
Standard Signal Isolating Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and conversion of standard signals. Calibrated switchable inputs and outputs 0/4 ... 20 mA and 0 ... 10 V signal duplicator with two electrically isolated outputs.
-
product
Resonant Chopper Systems
Electro-Optical Products Corp.
An external clock signal, to provide an ultra stable modulating optical beam motion [sub] system. The system can be used as a "stand alone" unit, in the laboratory, or can be incorporated into a larger instrument/system. The chopper is ONE FIXED FREQUENCY, picked from the range of 5 Hz to 20 kHz. The chopper is a small size, light weigh, low cost and long life device. It requires low power drive electronics and does not radiate electromagnetic interference (EMI). It has high frequency stability and high amplitude stability. The chopper is IR, VIS and UV and high vacuum capable. Reference signal and position output available.
-
product
Battery Powered Telemetry Systems
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
product
Digital Geophone
ZET 7155
Digital geophone ZET 7155 is a vibration sensor with an integrated sensing element enabling conversion of ground oscillations velocity into a proportional electric signal. Vibration speed value is calculated automatically by means of an integrated processor.
-
product
PXI Very High Density Multiplexer, 49-Channel 2pole
40-670C-021-49/2
The 40-670C-021-49/2 is a 49-channel, 2-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
Wavefront Modeling And Simulation
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
product
Reverse Test Probe
I-Stop
The I-Stop Reverse Test Probe is a test accessory designed for use with most signal level meters and with the Trilithic 9580 Return Maintenance System. Screw the probe into a distribution tap's unused KS port and a spring-loaded "stinger" connects a 20 dB resistive test point circuit to the hardline.
-
product
PCI-4461, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 2-Input/2-Output Sound and Vibration Device
779307-01
The PCI‑4461 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous two-channel dynamic signal generation and simultaneous two-channel dynamic signal acquisition with six gain settings to configure the input range. The PCI‑4461 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 50 GHz, 50 Ω, SMA-2.4, Terminated, Remote Mount, Failsafe
42-785C-452-TE
The 40-785C-452-TE (PXI) and 42-785C-452-TE (PXIe) are dual failsafe SP4T 50 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
Diode Arrays
a silicon diode with minimal packaging overhead. The small signal 0603, 1005 and 1206 Chip Diodes are lead free with Cu/Ni/Au plated terminations while the other packages (SMA, SMB, SMC, 1408, 1607, 2010, 2419, 8L NSOIC, 16L NSOIC, SOT23, SOT23-6, 16L WSOIC) use 100 % Tin terminations. All Bourns® diodes are compatible with lead free manufacturing processes, conforming to many industry and government regulations on lead free components.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-01
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
PCI-5922, 24-Bit, Flexible Resolution PCI Oscilloscope Device
779659-03
24-Bit, Flexible Resolution PCI Oscilloscope Device - The PCI‑5922 high resolution oscilloscope device features a flexible measurement resolution range up to 24 bits and up to 15 MS/s rates. This oscilloscope device has flexible settings for coupling, and voltage range, as well as a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. The PCI‑5922 is capable of taking extremely resolute and accurate analog measurements. It is ideal for audio signals, spectrum analysis, and any other small, accurate signal measurements.
-
product
Fully Differential Amplifiers
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
product
Thermal Inducing System
Wewon Environmental Chambers Co, Ltd.
Design and development is the stage with the most type of thermal inducing system, It mainly includes oscilloscope, signal source, spectrum analyzer (signal analyzer), vector network analyzer and other general thermal management solutions, As well as channel simulator, terminal simulator, base station simulator and other dedicated thermal inducing system.https://www.wewontech.com/thermal-inducing-system/
-
product
Calibrating Equipment
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
product
LXI Microwave Multiplexer, SP6T, 1-Bank, 26.5GHz, 50Ω, SMA
60-800-301
Our 60-800-301 is a 1 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Battery Powered ICP® Sensor Signal Conditioners
Battery-powered signal conditioners offer a portable and convenient solution for powering ICP® sensors and ICP® in-line charge converters, facilitating seamless integration into any measurement chain. Utilizing these units is straightforward: simply connect a cable from the sensor to the input and another from the data acquisition system to the output. Once powered on, they efficiently condition signals for transmission to the readout device.
