In-circuit Test Systems
See Also: In-circuit, Incircuit, In-Circuit Debuggers, In-circuit Emulators, In-circuit Probes, In-Circuit Test, In-circuit Testers
-
product
MEMS Test System Development
olidus Technologies’ can design and build a test system customized for your exact needs, using our own or off the shelf components:Custom MEMS Test Systems. We can integrate and assemble test equipment and handling systems to fit your requirements. Custom MEMS Test Software. We can write custom software for device-specific calibration and testing, interfacing various instruments and handling systems, or create a customized GUI. We can also adapt our standard STI Test Software to work on your hardware system.
-
product
Engine Emission Test System
By adding transient operation functions (self-learning/predictive driving + each test mode performing) to measurement•control panel, Ono Sokki can build up engine test system that can perform transient mode tests supporting worldwide gas emission controls including TRIAS, FTP, EURO, and ISO. (e.g. WHDC, NRTC).This system provides good reproducibility for Transient mode test. Delay compensation and rotation inertia compensation function have greatly improved as well as self-learning / predictive driving function.Automatically processes from measurement to data output of test result, in conjunction with gas emission analyzer, tunnels, gas emission particle measurement system, smoke meter, etc.
-
product
Instrument Transformer Test Systems
Our systems for testing voltage (VT) and current (CT) instrument transformers are conceived among other things for testing accuracy and insulation.
-
-
product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
product
Test system for Electronic Device
PCB
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
product
WEIGHING SYSTEM TESTING
1006
The Tester 1006 has a simultaneous control function of up to 4 load cells in any weighing system, upload and download function for programming the DAT and MC 302 series instruments, but it can also be used as a Calibrator and Peak detector. It is very useful for the correct mechanical installation and for fault diagnosis. The Tester 1006 is supplied as standard with cable for connection to our junction boxes / sum mod. CEM 4 / C and CGS 4 / C. Simultaneous display of the signal of each individual load cell allows to control the entire weighing system, weight distribution, overloads, faulty cells and faulty connections. OUT OF PRODUCTION. Pavone systems provides a new version of Tester 1006: Tester 1008.
-
product
Microtester Test Systems
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
product
Automated Test System
Automated Test System is a production-ready solution that combines test software and various hardware for validation test in both manufacturing and R&D. The solution provides a high performance and cost-effective system based on National Instruments technology.
-
product
Test System
ETS788XL
The 50/100 MHz ETS788XL system is the compact protable version of our ETS788. Made with the new high-performance precision components of our Griffin series, this portable powerhouse offers an optional tough road case and ready to go to any test site needed. Just pop off the covers and get started. Whether it's research, Failure Analysis, or single-event effects testing, his powerful member of the HiLevel family takes advantage of all of the tried and true features that have served users so successfully to date.
-
product
Multi-Stage Functional Test Systems
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
product
Car-to-X Test Systems
Qosmotec Software Solutions GmbH
Wireless Communication Technology is finding its way into automotive industry – not only for entertainment purposes, but for security and safety reasons: With Car-to-X technology, drivers shall get information that other vehicles and road side facilities already have, for example, in case of a traffic jam ahead, a slippery road behind a curve or a necessary change of the traffic lane because of road constructions.
-
product
Vibration Test System
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Vibration Test System is a simulation of the various environments encountered in the manufacturing, assembly, transportation and use phases of execution. It is primarily used to identify the ability of a product to withstand environmental vibrations.
-
product
Transformer Test System
Transformer testing instrument, can be used as a stand-alone device and has the highest efficiency. Can be used in power transformers, network communication transformers, etc.
-
product
Production Test System
G3 Hybrid
The G3 Hybrid is a state of the art system for fast Production test throughput in DC test applications. The system combines the most versatile offerings of features in a single system, at the lowest cost. For devices requiring DC and Continuity test capability only, G3H is a very flexible cost-effective Production Test solution. This approach provides a DC test system with the capability to add logic resources (AC/SCAN) as well as analog resources for Mixed Signal. The HILEVEL G3H embraces low cost while supporting SCAN, giving you the ability to toggle every node in your chip.
-
product
In-Circuit Testers
SPEA’s Bed of Nails Board Testers are scalable In-Circuit Test platforms that deliver the shortest test time, superior diagnostic accuracy, and extended test coverage for the most comprehensive range of electronic products.SPEA’s In-Circuit Board Testers are designed to increase yield, shorten the testing time, and cut the cost-of-test. Thanks to their unique Multi-Tester and Multi-Core Architecture, the SPEA’s Board Testers provide up to ten times greater throughput than conventional ICT test systems.
-
product
Engine Test Systems
Today''s engines and components require testing in a repeatable manner over a wide variety of conditions, ensuring that the final manufactured product consistently meets customer demands for performance and durability. The need for engines to be both economical and - above all - environmentally friendly, places fresh challenges on developers.
-
product
Memory Test System
T5835
The new T5835 has full testing functionality, from package testing to high-speed wafer testing, for any memory ICs with operating speeds up to 5.4 Gbps, including all next-generation memories from NAND flash devices to DDR-DRAM and LPDDR-DRAM. It can handle 768 devices simultaneously for final package-level testing. It additionally features functions such as an enhanced programmable power supply (PPS) for advanced mobile memories, and a real-time DQS vs. DQ function to improve yield.
-
product
Test Automation System for Driveline Testing
STARS Driveline
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
product
Transmission Performance/Endurance Test System
This system is suitable for vehicle drive test with only the transmission unit in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling engines, tires or vehicles other than transmission. The engines, tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
product
Portable Test System
MT686s
Actual value, vector, curve displaypower generationerror measurementMeasurement of harmonics up to the 40thVoltage supply via existing measurement voltage
-
product
Powerful In-Circuit Production Flash Programmer
CYCLONE FX
P&E Microcomputer Systems' Cyclone FX programmer is is a powerful in-circuit, stand-alone programmer that supports a wide range of ARM Cortex and NXP® processor families. It's a versatile tool that offers on-board storage of programming images, provides power to the target, supports manual or automated programming, and has an easy-to-use touchscreen interface. Programming may be launched by a single button press without a PC or automatically from a PC via the automated control SDK. The Cyclone may also be used as a debug probe during development.
-
product
Slip Ring Test System
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
product
Automated Shock Test Systems
AutoShock-II Test System
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
product
Multi-Purpose RF Test System
SPA1241
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
product
Zero-distance Drop Test System
KRD40 series
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
-
-
product
COMPUTERIZED LCRTZ TEST SYSTEM (Automatic Transformer Test System)
CVCT-S20
Ideal for fast and fool proof testing of COILS AND SMALL TRANSFORMERS like SMPS transformers, Telecom transformers (HYBRID, POT CORE, RM-CORE), Pulse transformers etc. The systems scans at one stroke, all the windings of a transformer and tests as per definition of test procedure. The test procedure can be pre-programmed and stored under User friendly menu driven software . Any semi-skilled and unskilled person can be engaged for actual testing purpose. Can Select test frequency, pin number, parameters, test conditions, limits for each test. Test any pin to any other pin any defined parameter.Test Parameters :-> Inductance-> Capacitance-> AC Resistance, -> DC Resistance, -> Impedance, -> Leakage Inductance,-> Transformation Ratio & Winding PolaritySPECIFICATIONS :Measurement Frequencies : 50 Hz, 100 Hz, 500 Hz, 800 Hz; 1 KHz, 2 KHz, 5 KHz, 10 KHz. Measurement Voltage: 0.1 V – 1.0 V RMS adjustable under program control.
-
product
Analog In-Circuit Tester
406C
The 406C is an open architecture power up test platform designed to facilitate the implementation of functional testing after the MDA test is completed. Internally dubbed as "Armadillo" the new architecture provides the user almost unlimited flexibility by combining the best of the VME buss and a dedicated ICT buss.
-
product
FPGA Test System
DO-254/CTS
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
