-
Product
Optical Thin-Film Metrology for Advanced Thin Films
FilmTek 6000 PAR-SE
-
Scientific Computing International
Production-proven metrology system for film thickness, refractive index and stress measurement for a broad range of film layers at the 1x nm design node and beyond. Accommodates 200 or 300 mm wafer metrology. Combines spectroscopic ellipsometry and DUV multi-angle polarized reflectometry with a wide spectral range to meet the challenging demands associated with multi-patterning and other leading-edge device fabrication techniques.
-
Product
HALT/HASS Testing
HALT HASS Chamber
-
AST applies stresses (such as temperature and vibration) to products well beyond its normal use environment. This type of testing is done to determine product operating and destruct limits. These stresses are applied as the product is functionally tested and continuously monitored for failures.Highly Accelerated Stress Testing (HALT) and Highly Accelerated Stress Screening (HASS) are two types of accelerated stress testing. These types of tests are commonly used to eliminate design problems, helping to develop a robust, mature product prior to market introduction. It can also be used to screen out infant mortality issues prior to shipment.
-
Product
Flammability Test System
COMP0804CAP
-
Active flammability test system according to IEC 60384-14 Ed4. For testing X & Ycapacitors up to 1uF. The test system includes control of the nominal AC supply via an integrated variac up to 1800V. Impulse amplitudes are programmable up to 8kV which covers all requirements. X1 capacitors are stressed up to 4kV, X2 and Y4 capacitors up to 2.5kV and Y2 capacitors up to 5kV.
-
Product
Terminal Mechanical Strength Test
-
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
Product
Computer Servo Control Testing Machine for Rock Stiffness
YAW-G300
-
Jinan Testing Equipment IE Corporation
The Computer Servo Control Testing Machine for Rock Stiffness is used for static fatigue compression test for conncrete & rock material under different parameter. The test includes compression, shearing test, three-point bending testing & fatigue test. Meanwhile, the Computer Servo Control Testing Machine can also realize the automatic control, measuring, data processing; curve analyzing, result displaying and test report printing in the process of various tests. The stiffness testing system can do full process test under stress and strain.
-
Product
Mechanical Tester
-
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Product
HAST Accelerated Aging Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is glad to be the ODM/OEM manufacturer of HAST chamber,HAST aging test chamber,HAST test chamber, HAST aging test chamber Accelerated Stress Test Chamber,High-pressure accelerated aging test sales enterprises all over the world!
-
Product
Digital Shore C Rubber Hardness Tester
HS-C
-
Shenzhen Chuangxin Instruments Co., Ltd.
HS-C is a digital micropore hardness, is for the foamer rubber and plastic microporous material when the compression rate is 50%and the stress is more than 0.5 kg/cm
-
Product
Science Bay Module for Gavia AUV
-
The Gavia Science Bay Module is a generic payload module that allows a Gavia user to add up to six scientific sensors to the Gavia AUV. The module includes several hull penetrations, including four (4) penetrations that can accommodate WetLabs ECO pucks, two external wet plugs that can provide power and serial communication for external devices, one slot for a SeaBird CTD, one penetration that can accommodate an Aanderaa Optode oxygen sensor, as well as a weak link on the bottom of the module. The weak link provides the option of towing an external sensor and reduces stress on the wet plug.
-
Product
Encoder Stress Pattern
ESP™
-
SRI's ESP is a sophisticated video clip consisting of specialized and complex artificial test patterns that stress various aspects of processing to quickly reveal television encoder deficiencies. Its unique motion sequences allow users to visually evaluate and objectively compare the quality and performance of standard- and high-definition encoders.
-
Product
Highly Accelerated Stress Test Chambers
HAST
-
Our HAST systems have a modern design that's easier to use: Automatic humidity filling; Automatic door lock; A more square workspace; allowing more product to be loaded;Convenient, hermetic power-pin system for bias testing. We are now able to offer a hermetic port system to allow special signal lines like coax or fiberoptics to be run into the chamber.
-
Product
FEA Software
Autodesk® Nastran®
-
Autodesk Nastran FEA software analyzes linear and nonlinear stress, dynamics, and heat transfer characteristics of structures and mechanical components.
-
Product
Strength And Hardness Testing
-
Strength measures how much stress can be applied to an element before it deforms permanently or fractures. Hardness measures a material's resistance to surface deformation.
-
Product
Environmental Stress Screening (ESS) Chamber
ESS
-
Developed to help electronics manufacturers detect product defects and production flaws, Environmental Stress Screening (ESS) forces infancy product failures that would otherwise occur after final assembly and product delivery. ESS’s goal is to improve profitability by eliminating defective products. ESS Systems can meet individual performance needs, product loading, and throughput requirements. Thermotron has the experience to provide the best solution for ESS testing at your company.
-
Product
Pull Out Device
BCL-1
-
This Pull out device BCL-1 is designed and manufactured according to relevant standard requirements of IEC884-1/ GB2099.1-2008 and other electrical accessories standards, Mainly used to test the needed maximum force when the plug pull out from socket and the minimum force when single stage plug pull out from socket, and to inspect whether the socket can withstand the lateral stress imposed by electric plug into the socket. This device is applied to plugs and sockets which rated voltage no more than 250V and rated current no more than 16A.Specifications: • Weights: 36N*1, 5.4N*1, 5N*2, 4N*1, 2.6N*1; • Standard testing plug: each one for Dipolar 10A, tripolar 10A and 16A • Standard test bolt: Each one for 1.5N and 2N • 1 set of clamping device • 1 set of Weights tray • Lateral stress weights 5N*1 • 1 set of lateral stress bar
-
Product
Wafer/Chip/Package Semi-automated ESD Tester
400SW
-
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection. Stress level and measurement points are programmed by personal computor via GP-IB. Once test terminals are selected, ESD endurance is automatically measured.
-
Product
Air Core Current Limiting Reactors
-
Current Limiting Reactor (CLR) is one of the most effective short circuit current limiting devices. It reduces stresses on busses, insulators, circuit breakers and other high voltage devices. Use of CLR is the most practical and economical approach at current limiting.
-
Product
Standard Climatic Test Chamber(Environmental Chamber)
-
Guangdong Test EQ Equipment co., Ltd.
Primarily used for accelerated damp heat testing, alternating damp heat testing, constant humidity testing, as well as high/low temperature routine testing, cold resistance testing, low-temperature storage, and adaptability testing under rapid or gradual temperature changes in industries such as aviation, aerospace, electronics, instrumentation, electrical products, materials, components, equipment, and complete machines. It is particularly suitable for Environmental Stress Screening (ESS) testing of electrical and electronic products or for enhancing production efficiency. It enables analysis and evaluation of performance and behavior under simulated environmental conditions.
-
Product
Environmental Testing
-
Environmental Testing is the evaluation of a product in conditions which simulate the physical environments that may harm or adversely affect the products performance. Environmental testing can play an important role throughout a product's development cycle to ensure that the materials and manufacturing processes can survive the stresses of the environment in which the product is likely to operate. These environments may include high and low temperatures as well as quickly changing temperatures. Also, temperature humidity environments may also be a factor. Environments with an added media such as dust, ice and freezing rain may also have an adverse effect on products. Listed below are some of Global Testing Services Environmental Testing capabilities
-
Product
Kelvin Test Contactor
ecoAmp
-
ecoAmp™ Kelvin test contactor has a durable monolithic pin design with low and stable contact resistance. It is a high-power cantilever kelvin contactor with a patented spring and tip design for optimum heat dissipation. This ensures best reliability, long spring life and high yield even under highest current and temperature requirements. Featuring extended Automotive temperature range -60 ̊C to +175 ̊C, capable to stand thermal stress during high-power test. The contact motion is decoupled from the test board.
-
Product
Chlorophyll Fluorometer
OS1p
-
This instrument provided the most used plant stress measuring protocols, at a much lower price. OS1p capability includes the fast measurements.
-
Product
Strain Measurements and Experimental Stress Analysis
-
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
Product
Cloud Based Scalability Testing
-
Perform load and stress tests on your system using a scalable cloud based platform. Get results on demand and ensure that your infrastructure scales.
-
Product
Environmental Stress Screening
E.S.S
-
King Design Industrial Co., Ltd.
E.S.S system could find most potential and hiding defects earlier by checking the physical property of allmaterials and components, and make use of their nature response under Environmental Stress. Through our screening will to pick out all potential and hiding defects in advance and improving the product's reliability inling. It benefits the manufacturer and customer mutually.
-
Product
Field Testing
-
When Laserline delivers a customer-specific solution, it makes sure that it fulfills every demand in the practical field. And that is because every newly designed customer solution is extensively tested in our own application laboratory and has passed comprehensive stress tests. These tests are made in close consultation with our customer as well. In this way, it is guaranteed that the demands are correctly identified and addressed with respect to practice.
-
Product
Humidity Detectors
-
A humidity detector, also referred to as a humidity meter or humidity gauge, is a device with a humidity sensor that measures the relative humidity in the air. PCE Instruments offers a number of humidity detector products including handheld humidity detector, data recording or data logging humidity detector, and combination or multifunction humidity detector devices that also measure parameters such as room or ambient temperature and atmospheric or barometric pressure. A humidity detector can measure relative humidity (RH) as a percentage (%) from 0 to 100 % RH, depending on the humidity measurement range of the specific model.Humidity is a key factor in everything from library and museum archival to agriculture, construction, manufacturing, transportation, warehousing, and heating, ventilation, air conditioning and refrigeration (HVACR). A relative humidity meter also is helpful in evaluating workers' heat stress risk on production floors and job sites. In addition, humidity plays an important role in the residential sector. If the humidity is too high in a private household, mold can grow. Mold creates a health hazard for anyone breathing the air in the home.
-
Product
Shear Beam LoadCells
-
Shear Beam LoadCells are designed for low profile scales and process applications. These loadcells should be mounted on a smooth flat surface using high strength hardend bolts. The mountaing holes are at the opposite end to where the cell is loaded. Some of the larger Shear Beam Loadcells use multiple mounting holes to allow extra bolts to hold them in place and keep them from stretching under the stress.
-
Product
ESD/EOS Consulting services
-
Dangelmayer Associates, L.L.C.
Dangelmayer Associates offers a full range of customized ESD/EOS(Electrostatic Program Management/Electrical Over Stress) professional consulting services on a Global basis for both product design and manufacturing, including but not limited to S20.20 Programs, Class 0, CDM, Charged Board Events, S20.20, EOS and Cleanrooms.
-
Product
High Strain Pile Driving Analyzer, Pile Testing Machine
SG-PDA
-
It is a state-of-the-art testing equipment to perform high strain pile bearing testing on piles.It will provide prediction on the pile bearing capacity, pile integrity, driving stresses and hammer performance for a given pile penetration. It is a relative low cost type of pile testing compared to static load test (MLT or CRP). The testing technique is quick and accurate.It can also be used to perform high strain pile bearing monitoring to evaluate pile driving information for pile bearing capacity, pile integrity, driving stresses and transferred energy against pile penetration. The results are essential for the actual pile driving process and to obtain valuable data on the hammer, pile & soil system for re-design on the piled foundation (if necessary).
-
Product
RF Automated Accelerated Reliability Test Station (AARTS)
RF-HTOL
-
The RF Automated Accelerated Reliability Test Station (AARTS) systems are designed to stress devices with RF, DC, and thermal stimulus. The systems were designed from their inception to include RF stimulus - it was not added as an after-thought. Hence, the software and hardware are fully integrated and provide full-featured support.
