-
Product
PXI Strain Gauge Simulator Module 6-Channel, 1.5k
40-265-406
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Strain Relief Plate, ITA, 90 Series
510109296
Strain Relief
ITA Strain Relief Plate works with all ITA modules. Plate is not needed for ITAs with cable clamps.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1.5k
50-265-404
Strain Gauge Simulator
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Strain Relief Plate, ITA and Receiver, 90 Series, High Power
510109549
Strain Relief
Strain Relief Plate, ITA and Receiver, 90 Series, High Power
-
Product
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions
510109598
Strain Relief
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 2k
50-265-302
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
C Series Strain/Bridge Input Module
Strain/Bridge Input Module
The C Series Strain/Bridge Input Module works with higher-channel-count, dynamic strain measurement systems. Modules can acquire measurements from up to eight channels, with compatibility options for quarter-, half-, and full-bridge sensors. The C Series Strain/Bridge Input Module is ideal for application channels requiring measurements at particular times, such as impact tests. It includes built-in voltage excitation, as well as transient isolation for high-common-mode noise rejection and improved safety.The C Series Strain/Bridge Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Strain Relief Plate, Receiver, 90 Series
510109298
Strain Relief
Strain Relief Plate works with all 90 Series receiver modules.
-
Product
Strain Relief Stand-off Kit, ICon, Receiver
310113582
Strain Relief
Strain Relief Stand-off Kit, iCon, Receiver.
-
Product
Strain Relief Plate, Receiver, QuadraPaddle, 192 Position
510109349
Strain Relief
Strain Relief.
-
Product
NI-9235, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
785995-01
Strain/Bridge Input Module
10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
Strain Gauges
TSM
-
We have been designing and manufacturing strain gauges for over 50 years and one of the earliest members of the British Society for Strain Measurement: Linear Strain, Dual Strain, Full & Half Bridge, Rosette & Circular, Bonding Services, Torque & Shear Strain Gauges and Bi-Axial/Tri-Axial Strain Gauges.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Strain Relief Plate, Receiver/ITA, I1/D1
310113531
Strain Relief
Strain Relief Plate, Receiver/ITA, i1/D1
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 1.5k
40-265-404
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
Strain Gauge Module
МТМ8
-
Mezzanine module (mezzanine) МТМ8 is designed to measure the output signal of strain gauges. The mezzanine can be used with any bridge sensors (pressure, force, etc.).
-
Product
Strain Gauge Test
-
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
-
Product
Strain Gauges
-
Available in a variety of models to cover most strain measurement applications. Rugged construction and flexibility make them suitable for highly accurate static and dynamic measurement.
-
Product
Software for Strain-Gauge Stations
ZETLAB TENZO
-
Software ZETLAB TENZO is included into the delivery scope of Strain Measurement Acquisition Module ZET 017-T8. This software and hardware kit allows you to start taking measurements immediately after device connection and installation of the software.
-
Product
Strain Relief Plate, Receiver, 90 Series
510109116
Strain Relief
Strain Relief Plate for Select Receiver ModulesWorks with Receiver Modules: 510104102, 510104120, 510104123, 510104133, 510104134, 510104136, 510104149, 510104206, 510104243, 510104261
-
Product
Strain Relief Plate, Receiver, 90 Series, Micro Power/Micro Coax, 50 Pos
510109282
Strain Relief
Strain Relief.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 3k
40-265-106
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Strain Meters
-
Omega offers a large selection of Strain Meters for all strain gauge and load cell applications. All of our Strain Meters are built to deliver exceptional and accurate performance over the long-term.
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-8
-
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated
-
Product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
-
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 350
40-265-016
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Strain Sensors
-
Columbia Research Laboratories
Columbia's foil strain sensors monitor the fatigue loading experienced by tactical aircraft under various conditions of speed, weight and missions configuration. Critical undercarriage structures and control surfaces may be monitored for fatigue damage induced by high-G maneuvers and high stress landings. These sensors are self-temperatures compensating, environmental resistant, have a high output, two active arms and are easily installed.
-
Product
Strain Gage Testing
-
Response Dynamics Vibration Engineering, Inc.
Although strain measurement is often a key part of a root cause diagnosis, our analyses often also involve measurements of other parameters such as acceleration, relative displacement, pressure, temperature, flow, speed, load, dynamic stiffness, etc, to explore multiple parameters that may have a cause/effect relationship with the problem at hand. These measurements form part of a fact based hypothesis for the cause of the problem at hand. We use stain gauge testing and/or stain modeling and analysis, in conjunction with our structural dynamics expertise to characterize all the important pieces of the puzzle that come into play with dynamic strain issues (See Diagnostic Testing).
