-
Product
TTC-1 Tracking Test Chamber
TTC-1
-
It is according to IEC60695 and IEC60112 (GB4207), the Tracking Test Chamber TTC-1 is intended for determining the degree of protection against formation of conducting paths in solid insulating materials, due to the electric stress and electrolytic contamination of the surface. This method simulates tracking currents on insulation material by providing drops between electrodes. During the process of normal use, insulating material may be exposed to moisture and dirt, if conductive, may cause stress and fire hazard.
-
Product
DC Power Supplies
SFA Series
-
AMETEK Programmable Power, Inc.
The SFA family builds on the industry leading Sorensen SGA series to provide a high power current source for laser diode applications. State of the art high power laser diodes require well-regulated current control to avoid catastrophic damage. Under anomalous operating conditions, excessive stored energy in the output circuit of the power supply can result in peak stresses that can permanently damage the device. Providing a constant current regulation mode only, the SFA’s low stored energy output minimizes damage potential for sensitive devices as well as enabling a current slew rate of up to 400 A/msec.
-
Product
Creep Testing Machine
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Measures the alteration of a material after it has undergone stresses.
-
Product
Physical
-
This category covers test equipment for verification of resistance to heat, fire, tracking, mechanical stress, endurance, impact, force, torque, dimensional accuracy & similar related parameters as required by national and international safety regulatory agencies. These equipment are used to check Electrical WiringAccessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Many of these test equipment are common to many standards and are essential for routine test purposes.
-
Product
Surface Mount Frequency Synthesizers
-
Corech Surface Mount Frequency Synthesizers series packs impressive low phase noise of -90dBc/Hz@1kHz, low spurious of -50dBc to -70dBc, high temperature and corrosion resistance, long operating life, temperature uniformity, and good thermal conductivity. These outstanding performance make it suitable for high-reliability and environmentally stressful applications including communication systems, test and measurement equipment, radar systems etc.
-
Product
Partial Discharge
-
Is a localized dielectric breakdown (DB) (which does not completely bridge the space between the two conductors) of a small portion of a solid or fluid electrical insulation (EI) system under high voltage (HV) stress.
-
Product
Science Bay Module for Gavia AUV
-
The Gavia Science Bay Module is a generic payload module that allows a Gavia user to add up to six scientific sensors to the Gavia AUV. The module includes several hull penetrations, including four (4) penetrations that can accommodate WetLabs ECO pucks, two external wet plugs that can provide power and serial communication for external devices, one slot for a SeaBird CTD, one penetration that can accommodate an Aanderaa Optode oxygen sensor, as well as a weak link on the bottom of the module. The weak link provides the option of towing an external sensor and reduces stress on the wet plug.
-
Product
Circuit Breaker Testing Equipment
HISAC Ultima
-
HISAC Ultima – new generation Circuit Breaker Dynamic Test Set from SCOPE …. The ultimate solution for testing Circuit Breakers of all types. HISAC Ultima is the most complete analyser for checking the dynamic performance of CBs in live EHV switchyards upto 765 kV. HISAC Ultima can carry out Dynamic Contact Resistance Measurement on SIX breaks of THREE poles in one operation thereby significantly reducing stress on CB & testing downtime.
-
Product
Humidity Indicators
-
A humidity detector, also referred to as a humidity meter or humidity gauge, is a device with a humidity sensor that measures the relative humidity in the air. PCE Instruments offers a number of humidity detector products including handheld humidity detector, data recording or data logging humidity detector, and combination or multifunction humidity detector devices that also measure parameters such as room or ambient temperature and atmospheric or barometric pressure. A humidity detector can measure relative humidity (RH) as a percentage (%) from 0 to 100 % RH, depending on the humidity measurement range of the specific model.Humidity is a key factor in everything from library and museum archival to agriculture, construction, manufacturing, transportation, warehousing, and heating, ventilation, air conditioning and refrigeration (HVACR). A relative humidity meter also is helpful in evaluating workers' heat stress risk on production floors and job sites. In addition, humidity plays an important role in the residential sector. If the humidity is too high in a private household, mold can grow. Mold creates a health hazard for anyone breathing the air in the home.
-
Product
Static Load Cells (5 N to 300 kN)
2530 Series
-
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
Product
Tensile Test Chamber
-
CSZ's Tensile Test Chamber is an environmental chamber that interfaces with a customer tensile tester load frame. This chamber is required to expose various materials and components to temperature conditions while undergoing tensile test. Tensile testing stresses materials by pushing, pulling, twisting, or bending intended for static and fatigue testing.
-
Product
kSA MOS
-
Measure and provide feedback for curvature, stress, reflectivity and growth rate to improve production processes and increase profitability with the kSA MOS.
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
Product
Static Load Cells (500 N to 600 kN)
2580 Series
-
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
Product
Humidity Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Humidity chambers offer a wide range of standard solutions for your testing program. Environmental testing with a humidity chamber helps improve product reliability and durability. Humidity chambers are available in a variety of styles, sizes, and performance configurations. All humidity chambers come with a standard temperature range for combined temperature and humidity testing.Humidity may affect the life expectancy of a component by creating stresses on the part materials and altering its electrical properties in a way that the component reliability is significantly diminished.Humidity tests are those performed with the aim of evaluating the properties of materials used in components and the reliability of non-hermetic packaged devices in humid environments.
-
Product
Plant Stress Kit
PSK
-
The Y(II) meter was designed to provide an inexpensive way to measure the fast light adapted Y(II) or F/FM' protocol and to make it available to more people that need it.
-
Product
High Temperature Wettability Tester
6200Z
-
This device is a test device that evaluates the wetting stress generated between a plate/round bar and molten metal in an inert gas atmosphere by the wetting balance method.It is possible to analyze not only the quality of wetting but also the wetting phenomenon from the obtained wetting curve.
-
Product
Air Humidity Meter
-
Since air humidity is an important factor in many sectors including but not limited to manufacturing, agriculture, construction, restoration, remediation and heating, ventilation and air conditioning (HVAC), PCE also carries a number of air humidity meter devices designed for specific applications such as evaluating heat stress risk in hot work environments like boiler rooms, factories, construction sites and commercial bakeries. To accurately assess heat stress risk, an air humidity meter capable of detecting and classifying temperature in relation to the amount of moisture content in the air is recommended. The global standard description for heat stress is the Wet Bulb Globe Temperature Index (WBGT).
-
Product
LOADpro Load Testers
-
LoadPro is an external Web load testing service. A LoadPro test simulates actual user traffic from outside your network, stressing your entire infrastructure in order to discover bottlenecks that impact performance under peak traffic.
-
Product
Highly Accelerated Stress Screening (HASS) Test
-
HASS consists of high and low temperature and 3 axis vibration testing performed either individually or in combination.Highly accelerated stress screening is a technique for identifying process flaws in equipment during production. HASS subjects equipment to overstress conditions but at a level which does not affect design life.For assistance in designing a HASS test program contact the laboratory.
-
Product
Rotational Rheometer
ARES-G2
-
The ARES-G2 is the most advanced rotational rheometer for research and material development. It remains the only commercially available rheometer with a dedicated actuator for deformation control, Torque Rebalance Transducer (TRT), and Force Rebalance Transducer (FRT) for independent shear stress and normal stress measurements. It is recognized by the rheological community as the industry standard to which all other rheometer measurements are compared for accuracy.
-
Product
HAST Accelerated Aging Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is glad to be the ODM/OEM manufacturer of HAST chamber,HAST aging test chamber,HAST test chamber, HAST aging test chamber Accelerated Stress Test Chamber,High-pressure accelerated aging test sales enterprises all over the world!
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
Solder Wettability Tester
5200TN
-
Amid the rapid progress in miniaturization of electronic components in high-density mounting, a long-established company that has been manufacturing solder wettability testers for about 40 years has developed a solder wettability tester compatible with the latest micro electronic components. and is the top model in the history of solder checkers with improved operability. * Wetting stress is proportional to the circumference of
-
Product
Torsion And Shear Strain Gauges
-
Shear/Torque Strain Gages are for measuring shear strain and torque, typical applications are for measurements on torsion bars and determining shear stresses in shear beam load cells.
-
Product
Leak And Seal Strength Detector
LSD-02
-
Jinan Leading Instruments Co., Ltd.
LSD-02 Leakand Seal Strength Detector is applicable in the quantitative measurement of leak, heat seal strength, heat seal quality, and burst pressure of each heat sealedges of the flexible packages that are made using heat seal and adhesiveprocessing, as well as sterilized packages; the quantitative measurement ofleak performances of all kinds of plastic pilfer-proof closures; thequantitative measurement of the unitary airproof, compression resistancestrength, cap body joint strength, cap disengaging strength, seal strength ofedge and butting strength of various flexible tubes. It can also provideevaluation and analysis for the compression and burst resistance strength ofthe materials of flexible packaging bags, the torsional airproof index of cap,the cap joint and disengaging strength and the stress strength; as well as theairproof performances, the compression resistance performance and the burstresistance character of unitary bottle, etc.
-
Product
HALT Test Service
-
HALT, Highly Accelerated Life Test is a system design validation tool for maximum robustness verification. In a step stress approach a system under functional test and operational conditions is check for functional and destruct limits.
-
Product
Industrial Freezers
-
Our industrial freezers are designed for various types of cold storage applications from light duty storage in areas where laboratory freezers aren't adequate to heavy-duty applications for harsh environments. These chest-type freezers are primarily used for age-hardening, stress relieving, expansion assembly, martensiting, dimensional stabilization, epoxy storage, industrial cooling, heat treating and production chilling applications.
-
Product
DC Hi-Pot Tester
3010HP, 3025HP & 3050HP
-
The DC Hi-Pot test is an important part and parcel of the electrical safety tests mandated by standards organization world-wide. More than 80 per cent of faults in electrical and electronic systems are due to weak insulation caused by environmental factors such as dirt, grease, temperature stress, humidity, etc that affect the dielectric strength of the insulation material.
-
Product
Walk-In Solar Spectrum Test Chamber
-
WEIBER walk in Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. It is also called Walk in Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Solar spectrum chamber also known as Walk in Solar Simulation Test Chamber
