Interconnects
Links between systems, networks,nodes, equipment, devices, components and circuits.
See Also: Mass Interconnect, Connectors, Cable Assemblies, Interfaces
-
product
Plugbord
3795-1
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.100"(2.54mm) centers. 3-Hole Solder Pads One Side Only. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. All pad and bus surfaces solder coated for user convenience. No pattern on reverse side, edge contacts only. Convenient easy-to-read hole marking legend on wiring side.
-
product
Eurocard Plugbord
4616, 160-PIN VME64x
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 160-pin DIN connectors. 3-Hole Solder Pad Pattern on both sides. 3-Hole Solder Pads (0.28” x 0.080”) for interconnecting multiple component leads.Interleaved buses on both sides, back-to-back. Pad and bus surfaces solder-coated for user convenience. Row and column legends provided.
-
product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/cd
M8091BSCB
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
product
DIP Program Header
Series 675
DIP Program Headers. Aries DIP programmable headers offer unusual versatility for programming within the header itself. They can be individually programmed using cutters or Aries programming tool, Part No. T-675, available separately, to remove the interconnecting sections. Consult Data Sheet No. 22002 for Aries programming tool.
-
product
USB 4-port Hub For Elan's USB T&M Instruments
USBMicroHub4
The MicroHub4 has connections for 4 USB2.0 measurement tools, and uses only one host USB port. Elan's test and measurement products can be interconnected to allow them to operate in synchronised mode, or left non-connected for distinct operation.
-
product
6-Port PCI Express
PEX 8624
The ExpressLane™ PEX 8624 device offers 24 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 6 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 24-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
product
PCB Connectors
HDLP Series
Smiths Interconnect's HDLP series is a low profile, high density interconnect with integral sealing
-
product
20-Port PCI Express
PEX 8680
The ExpressLane™ PEX 8680 device is the industry's first PCIe switch to offer 80 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 20 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 80-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.
-
product
Time Domain Reflectometers
HL1100 Series
HYPERLABS HL1100 Series TDR instruments provide high-performance test and measurement capabilities for use in the field or in the lab. These instruments are used for applications such as fault detection in cables and interconnects, impedance characterization, time of flight analysis, water level measurement, and more.
-
product
4-Port PCI Express
PEX 8617
The ExpressLane™ PEX 8617 device offers 16 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 4 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 16-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213A
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts (610138200)
510150131
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
product
Plugbord
3797-2
VECTOR Electronics and Technology, Inc.
30 Gold plated edge contacts (15 each side) on 0.156"(3.96mm) centers. 3-Hole solder pads for interconnecting multiple component leads. All pad and bus surfaces solder coated for user convenience. No pattern on reverse side, edge contacts only.Convenient easy-to-read hole marking legend on wiring side.
-
product
Resistive Components
Diamond is the best thermal conductor on earth. Combined with a low dielectric constant, it is an excellent RF dielectric material for high-frequency applications in which thermal performance is equally critical. By applying cutting-edge thin film process and extensive millimeter wave design experience, Smiths Interconnect has created a high-performance line of resistive components. The resulting products, our Diamond RF Resistives® resistors, terminations, and attenuators, are significantly reduced in size and unparalleled in average and peak power handling.
-
product
NRZ Analysis for Signal Integrity Studio, WavePulser 40iX High-Speed Interconnect Analyzer
WAVEPULSER-SI-STUDIO-NRZ
Signal Integrity (SI) Studio uses SDA Expert (SDAX) serial data analysis software options to simplify NRZ or PAM serial data jitter, eye diagram, noise and crosstalk measurement and analysis setup.
-
product
Manual Step Attenuator, DC to 4 GHz, 0 to 11 dB, 1 dB steps
8494A
The Keysight 8494A, dc to 4 GHz manual step attenuator, offers exceptional repeatability and reliability. Attenuation is provided in 1 dB steps from 0 to 11 dB. Precision gold-plated leaf springs ensure long-life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
product
Signal Integrity TDR and VNA Software
80SICON IConnect
IConnect software is the efficient, easy-to-use, and cost-effective solution for measurement-based performance evaluation of gigabit interconnect links and devices, including signal integrity analysis, impedance, S-parameter and eye diagram tests, and fault isolation.
-
product
Receiver, G40x, 48 Module, For Slide Mount, Includes EMI Protection
310120163
Receiver, G40x, 48 Module, For Slide Mount, Includes EMI Protection.The G40x is a two-tier, 48 slot system that accommodates pull through removal of interconnect adapters with VPC modules, PCBs/ Wiring, and test cards in one piece. It offers 8 standard/90 Series discrete-wire module slots, plus space for 2 iCon series modules, as needed. This G40x is for slide mounting. The operation handle may be switched from the standard right side to the left. Slide kit and flange mounting kit purchased separately.
-
product
JTAG/Boundary-scan Digital I/O Module
ScanIO-300LV
The ScanIO-300LV JTAG/boundary-scan digital I/O module turns an IEEE-1149.1 boundary-scan controller (such as the Corelis PCI-1149.1/Turbo or NetUSB-1149.1) into a powerful digital interconnect and functional tester.
-
product
Digital/Pattern/PE Card
PE32H
The PE32H represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PE32H offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PE32H also supports deep pattern memory by offering 32M of on-board vector memory with dynamic per pin direction control and with test rates up to 66 MHz. With new 32M log memory, PE32H can capture 32 channels data or fail log.
-
product
Multiport Electronic Calibration Module (ECal), DC To 20, 6-ports
N7564A
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 20 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
product
Multiport Electronic Calibration Module (ECal), DC To 9 GHz, 6-ports
N7562A
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 9 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
product
OBD Development Kit
The OBD Development Kit is a modular development system designed to speed up the development of devices that interface with the OBD bus. It consists of the Interconnect Board, three removable modules (Power, OBD Drivers, and STN OBD IC), and an OBD cable.
-
product
eDAK For MAC Panel
JT 2147/eDAC for MAC Panel
The JT 2147/eDAK is a new variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within a MAC Panel ‘Scout’ mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry plus four independent, programmable TAP modules (two of type JT 2149 and two of type JT2149/MPV) on a single board that matches the MAC Panel Direct Access Kit (DAK) form factor. Overall this configuration offers four Test Access Ports, 64 Digital IO Scan channels and reconfigurable (SCIL) capabilities
-
product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
-
product
Pulse generator
9355-1
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
product
Switching Matrix
MUX
The Analog Signal Switch Unit serves as a 6-bus interconnect for 128 pins each to the Analog Measurement Unit (AMU05) for the In-Circuit test.
-
product
High Density, High Isolation Multiplexer Module
1260-38T
The Astronics 1260-38T brings a combination of density, versatility, expandability, and high signal integrity, making it ideal for construction of large switching systems. This module is user-configurable using inter-connecting relays as sixteen 1x8 muxes to a 1x128 mux under program control. Special shielding, design, and added front panel "guard" grounds increase the isolation and lower the crosstalk.
-
product
Passive Oscilloscope Probes
5900 SERIES
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
