Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
LXI 16x4, 10A, 1-pole Matrix
60-600-008
Matrix Switch Module
A high power single pole matrix module capable of switching up to 400VDC/250VAC, 10A (300W/2500VA max power)
-
Product
PXI 8 Slot BRIC 92x16 1-Pole (4 sub-cards)
40-560A-121-92X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
ZIO Module
-
For more expansion and convenience, we offer a ready to use ZIO modules which are specially designed for CAPA boards (3.5-inch embedded SBC). Axiomtek’s innovative ZIO extension form factor to extend multiple I/O helps system integrators to provide optimized solutions in a more cost-effective way.
-
Product
In-Line RF Test Station
AP770
RF Test System
ICT, Functional, Hipot, Vision, ISP and RF test with low cost fixtures in a very compact test station footprint Works with PCBs up to 450×550 mm or with palletized devices Space for up to 25 VPC mass interconnect modules or YAV switching units
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 2Ω to 6.97kΩ
40-252-130
Programmable Resistor Module
The 40-252-130 is a programmable resistor module with 1 channel which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
40-635A-008
Multiplexer Module
The 40-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Software
DataPRO
-
Diversified Technical Systems, Inc.
DataPRO is a powerful set-up, control and data viewing software including ISO MME support. The modern user interface is designed to help test engineers create, control and manage every aspect of a test. DataPRO can be installed with an SQL server database and configured with individual user logins and access levels to support facilities and users of all sizes and capabilities. DataPRO works with all SLICE, TDAS G5 and TDAS PRO hardware and is required for systems using SLICE PRO TOM, DIM or TDM modules.
-
Product
PXI 12-Slot BRIC Matrix, 50x32 1-Pole (10 sub-cards)
40-562B-321-50X32
Matrix Switch Module
The 40-562B-321-50X32 is a high density BRIC12 matrix module with a size of 50x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI/PXIe MEMS RF Multiplexer, Single 4-Channel, 4GHz, 50Ω, MCX
42-878-212
Multiplexer Module
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
PXI Power Relay Module, 3xDPDT, 20 Amp
40-166-901
Relay
The 40/42-166-901 is a PXI/PXIe high density power relay module with 3xDPDT switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
Elite™ 13.56 MHz RF Plasma Generators
-
The elite™ Series of RF plasma generators provides state-of-the art technology in a compact air-cooled package. The elite is designed with high speed closed loop control, a class E RF deck and a switching modulator for superior output performance. The elite design utilizes a single printed circuit board assembly for the full rack product virtually eliminating all internal wires and connectors and thereby providing the highest reliability available.
-
Product
IEEE 1394b/AS5643 Mil1394 (FireWire), Triple-Node Multi-Port, Communications
FW3
-
The FW3 function module provides IEEE 1394b/AS5643 (Mil1394) support on each of its three nodes, which are configured as 2 nodes with 3-ports and 1 node with 2-ports. AS5643 defined flight ready robustness and active transformer isolation to enable longer cable lengths (20 meter) between nodes. Together these standards provide the deterministic and redundant communications protocol required for Vehicle System (Flight Control) Networks. The FW3 multiple ports per node configuration allows the user to create tree, daisy-chain and looped topologies needed to optimize cable length and weight while creating redundancy.
-
Product
Thermocouple, Contact, ITA, Chromel, Type K (°C)
610113133
Thermocouple Contact (ITA)
Primary mating contact 610113131.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
Product
4-Channel High Speed Position Comparison and Trigger Module
ECAT-TRG4
Trigger Module
The ECAT-TRG4 is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-213-HI
-
The 40-230-213-HI (PXI) and 42-230-213-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 239Ω with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 470Ω
40-253-014
Programmable Resistor Module
The 40-253-014 is a programmable resistor module with 2 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 25x8 Matrix Module, 1-pole 2A 60W
40-507-001
Matrix Switch Module
The 40-505/506/507/508/509 are a range of medium density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 2-Slot BRIC Matrix, 29x8 2A 2-Pole (1 Sub-card)
40-565B-202-29X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
Product
Humidity/Temp USB data logger
EL-USB-2
-
This data logger measures and stores up to 16,382 relative humidity and 16,382 temperature readings over 0 to 100%RH and -35 to +80C (-31 to +176F) measurement ranges. The user can easily set up the logging rate and start time, and download the stored data by plugging the module straight into a PCs USB port and running the purpose designed software under Windows 2000, XP or Vista.
-
Product
50 Ohm BNC to BNC Cable Assembly
40-977-501-0.1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
cDAQ-9188 , 8‑Slot, Ethernet CompactDAQ Chassis
782824-01
Chassis
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 18 GHz, 50 Ω, SMA, Internal Termination, Failsafe
42-781A-022
Relay
The 40-781A-022 (PXI) and 42-781A-022 (PXIe) are dual failsafe SPDT 18 GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
VPX GPGPU Processor Card
VPX6-4943
-
Curtiss-Wright Defense Solutions
The rugged VPX6-4943 single or dual NVIDIA Quadro GPU processor is designed and manufactured by Wolf Advanced Technology. This product is part of a family of GPGPU modules available from Curtiss-Wright Defense Solutions to enable development of High Performance Embedded Computing (HPEC) systems.
-
-
Product
Text-Based Way to Connect & Disconnect Relays on ABex Modules
ABex Switching
-
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
Product
3GHz 16-Channel Signal Generator 19" 3U Rack Module
LS30816R
Signal Generator
The LS30816R, 3GHz 16 channel RF Analog Signal Generator, offers industry leading performance, in a 3U, 19” space efficient, rack-mounted box. The LS30816R features 16 phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. With the highest channel density in the market the LS30816R offer the ideal solution for applications requiring high channel count at minimum space and cost.
-
Product
PXI 12-Slot BRIC Matrix, 572x4 2-Pole (13 sub-cards)
40-562B-322-572X4
Matrix Switch Module
The 40-562B-322-572X4 is a high density BRIC12 matrix module with a size of 572x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
