Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
8-CH Isolated Digital Input Module
ND-6052
Data Acquisition Module
- Channels: 8 DI. 6 fully independent isolated; 2 isolated with common ground- Isolated Voltage: 5000 VRMS- Programmable input polarity
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xSPST, Normally Closed
42-145A-001-NC
Relay
The 40-145A-001-NC (PXI) and 42-145A-001-NC (PXIe) 50xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
CMX RF Port Extender
CMX-Z25
-
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
Product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
Carrier Board
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Electrical Interface
QSFP-DD 200G
-
Eoptolink Technology Inc., Ltd.
QSFP-DD 200G Eoptolink’s EOLD-162HG-E-10-1 QSFP-DD CWDM4, 8x25G Optical transceiver module are designed for use in 200 Gigabit links over 10km singlemode fiber. They are compliant with the QSFP-DD MSA. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP-DD MSA.
-
Product
Ethernet Field Modules
-
- Reliable transmission of machine data, process parameters and diagnostic data to the controller- Simultaneous data exchange with the controller and the IT world- Wide operating temperature range and high protection rating- Robust housing with high protection rating
-
Product
Coax, Contact, Receiver, 20/26 GHz, SF142B, 90 Series modules only
610102109
Coax Contact (Receiver)
Primary mating contact 610102110. (May mate with other ITA contacts, as well.)
-
Product
Automated Metrology System
EVG®50
-
High-throughput, high-resolution metrology for bonded stacks and single wafers. The EVG 50 (fully automated stand-alone tool) and the Inline Metrology Module (integrated in EVG''s high-volume manufacturing systems) offer highly accurate measurements at high speed, utilizing different measurement methods for a large number of applications. The tool''s application range covers multi-layer thickness measurements for determination of the total thickness variation (TTV) of an intermediate layer, the inspection of bond interfaces as well as resist thickness measurement, and meets the most demanding requirements of the yield-driven semiconductor industry.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors
42-850A-214
Multiplexer Module
The 40/42-850A-214 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Receiver, G12, 12 Module, With 15" Platform, For Slide Mount (slide Kit Required)
310104325
Receiver
The 15” G12 Receiver is a slide-mounted receiver. The 15” platform will support 180 lbs. when used in a slide mount configuration. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 40GHz, 50Ω, SMA-2.9, Internal Termination
40-781A-422
Relay
The 40-781A-422 (PXI) and 42-781A-422 (PXIe) are dual SPDT 40GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
TOC-Control Software
-
The TOC-Control L/V is PC control software provided with the TOC PC control modules. This software features excellent operability, provides a wealth of functions, and enhances analysis operations.
-
Product
PXI/PXIe RF Matrix, 16x4, 300 MHz, 50 Ω SMB With Loop-thru
42-727A-001-L
Matrix Switch Module
The 40-727A-001-L (PXI) and 42-727A-001-L (PXIe) are 16x4 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
COM Express
Computer on Module
COM Express, defined by the PCI Industrial Computer Manufactures Group (PICMG), is the most successful Computer-On-Module (COM) standard in the embedded market today. COM Express employs a mezzanine-based approach, whereby an off-the-shelve module with two 220-pin board-to-board connectors, plugs into a custom, application-specific carrier board.
-
Product
Copper, Type T (°C) Contact
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
Product
256kS/s/ch, 24-Bit, 4-Ch IDAQ Module For IEPE Sound And Vibration
iDAQ-801
-
Hot-swappable in iDAQ system4-ch simultaneous sampling up to 256kS/s24-bit resolutionDirect IEPE supplyAnti-aliasing filter equippedHigh gain up to ±187.5mV input range
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-120
Programmable Resistor Modules
The 40-297A-120 (PXI) and the 42-297A-120 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
SIM 90 Series Modules
The SIM Modules
-
Snap-In-Modular (SIM) modules delivers a flexible, high‑density interconnect solution that supports multiple high‑performance contact technologies within a single module. The VTAC, Micro Coax, and QuadraPaddle SIM modules.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 450x4, 6 Sub-cards
40-568A-106
Matrix Switch Module
The 40-568A-106 is a PXI 1-pole 450x4 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-568A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Quad 4 To 1 RF Multiplexer, 8GHz 50 Ohm SMA, Terminated
40-882A-004
Multiplexer Module
The 40-881A-004 is a quad 50Ω 4 to 1 RF multiplexer with 8GHZ bandwidth.The 40-881A range of multiplexers have automatic termination of unused signals and are available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules.
-
Product
PXI 8-Slot High Density 2A BRIC Matrix, 87x8 2-Pole (3 Sub-cards)
40-573-102-87X8
Matrix Switch Module
The 40-573-102-87x8 BRIC is part of a range of high density matrix modules able to switch up to 2 A at 240 VDC/250 VAC. They are available in 2, 4 or 8-slot sizes to suit most high performance matrix requirements, constructed using quality electromechanical relays for high switching confidence.
-
Product
Ultra Compact, Uncooled Thermal Imaging Core
Dione S 1280 CAM Series
-
The Dione S 1280 CAM series is based on an uncooled 12 μm pitch microbolometer detector with a 1280 × 1024 resolution and NETD of less than 40 mK (available upon request) and 50 mK.The camera cores are optimized for low SWaP (Size, Weight and Power). The Dione S 1280 CAM is lightweight and small with mechanical shutter. It utilizes Xenics image enhancement for advanced image processing while keeping power consumption low.All Dione S 1280 versions have the same SAMTEC ST5 connector and are GenICam compliant. Dione S 1280 CAM is a LWIR uncooled thermal imaging SWAP module with housing supporting M34/M45 lens (optional).The ultra-compact Dione S 1280 CAM series find application in safety and security systems, as well as in industrial thermal imaging systems.
-
Product
PCIe-6536B, 32-Channel, 25 MHz, 100 MB/s Digital I/O Device
782630-01
Digital I/O
The PCIe-6536 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
LXI High Density 224x16 2A Matrix
60-554-007
Matrix Switch Module
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
IPM Drive
-
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
Product
VXI To PXI Transition Products
PXI/cPCI Carrier
-
The VX407C is an intelligent VXI carrier that allows PXI and cPCI modules to be used in VXI systems.
-
Product
Signal, Insert, Receiver/ITA, QuadraPaddle ,SIM, Right Angle, 4 Pos, 1 Slot
610138126
SIM Insert
This insert contains 4 right-angle QuadraPaddle contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 1 of the 34 slots in this module.
-
Product
Sonar Transponder Module for Gavia AUV
-
THE SONAR TRANSPONDER MODULE (STM), is a module for receiving and retransmitting sonar signals which allows for a standard Gavia vehicle to be configured as a Sonar Training Target (STT) for ASW training purposes. The STM consist of a flooded transducer compartment, an electronic compartment and a hydrophone that is towed behind the Gavia AUV and is capable of simulating preprogrammed target characteristics. The STM is programmable to emulate different type of realistic submarine target sizes and speeds for cost effective and re-usable ASW training capability.
