Test System Integrators
-
product
Mezzanine System
5041
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
product
Flight Control System Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
Mezzanine System
5085
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
product
Data Processing System
CRS-D8I-3VF1
The CRS-D8I-3VF1 VPX system’s I/O flexibility is capable of meeting a large number of configurations. It is designed to support Abaco Systems’ Intel 3rd generation Core i7 3U SBCs, Gigabit Ethernet switch, video compression card, CUDA-based graphics cards and a MIL-STD-1553/ARINC429 multi-protocol card.
-
product
Test System Optimized for High Volume Production Testing of Integrated Circuits
ETS-364 / ETS-600
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture. The test system offers separate floating resources for each site, improving site isolation and measurement accuracy coupled with digital instrumentation enabling the most efficient, high-volume testing available. The system supports up to 240 analog pin channels, and offers 133 MVPS digital vector rate with up to 128 digital pin channels. Eagle's scalability includes the ability to double the capacity of an ETS-364, providing more than 480 analog pin channels and up to 256 digital I/O pin channels with the ETS-600.
-
product
LabVIEW Full Development System
LabVIEW is engineering software designed specifically for test, measurement, and control applications that require rapid access to hardware and data insights. The LabVIEW Full Development System is recommended to customize your engineering application with advanced inline analysis and control algorithms. For applications that require software engineering tools to develop, debug, and deploy professional applications, consider LabVIEW Professional Development System.
-
product
Off-Line Seat Operation Base Test Platform
6TL23
The 6TL23 is a bare rack for creating Off-Line, modular, flexible, and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation since there’s space for the operator’s legs under the fixture receiver.
-
product
Digital Test Instruments
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.
-
product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
product
Explosive Test Site Range Instrumentation
Firesets, CDU’s EDU’s, Delay generators, firing panels, and custom instruments. Fiber-optic and computer-control options.
-
product
3-Axis Non-Robotic Automated Testing System
AT3
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
product
Electronics Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
product
Component Test Fixture For N1413 With B2980 Series
N1428A
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
product
6TL23 Off-Line seat operation Base Test Platform w/o Table
H71002301
- 18U height 19inch rack space (580mm depth)- VPC G12 or G12X interface- Man Machine interface H73000301 (not included)- stand-up operation
-
product
Valve Leak Measurement System
VLMS
The G Systems Valve Leak Measurement System (VLMS) reliably measures slow leaks that are unidentifiable with conventional leak detectors, helping manufacturers test and ensure that critical valves are absolutely airtight.
-
-
product
Off-Line Testing Platform
6TL29
6TL29 Testing platforms are based on the modularity concept; its construction is completely modular and scalable, allowing the user to take advantage of a powerful and reliable platform with a minimum investment.The platform is compact and due to its reduced footprint can be integrated easily into any production line. It’s ideal for High-Mix Low-Mid Volume production environments.
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
NI Vehicle Radar Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
product
PXIe System Sync Module, 2 Port
M9032A
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
product
The Compact AI GigE Vision Systems for the Edge with Intel Movidius Myriad VPU
EOS-i6000-M Series
The ADLINK AI Plug-and-Play (PnP) Solution is a set of ADLINK AI edge hardware and data connectivity platforms that help our partners build and deploy AI solutions faster and simpler. With ADLINK Data River™ enabled at AI edge platforms, devices, AI inferences, and data integrations, the AI PnP Solution offers a crossplatform, flexible, scalable solution that delivers business value.
-
product
VME Data Acquistion System
ADM-31
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
product
LabVIEW Development Systems
Base--The instant productivity of graphical development for DAQ and instrument controlFull--A rich set of routines for mathematics, signal processing, and signal generationProfessional--The solution for professional developers who need code deployment or validationLabVIEW suites--LabVIEW Professional plus industry-specific add-on software
-
product
Battery Cell Formation System
17000 series
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
product
VXI Digital Test Instrument
T940 Series
The T940 Series for the VXIbus provides the basis for a complete state-of-the-art digital solution at the subsystem level. The T940 is the solution for both legacy digital replacement and new test stations to be built for digital test including aircraft/ avionics, weapons systems, spacecraft, semiconductors and medical devices.
-
product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
product
High Throughput Test Platform for Multi-Site & Index Parallel Applications
ETS-88
The ETS-88 is an optimal test platform for testing a wide variety of devices including: simple analog, high precision, high voltage, high current / power, automotive, video, audio, complex mixed-signal, as well as emerging power processes like SiC and GaN.
-
product
Disk Drive Test System
Saturn
The Saturn HD is the industry leader in 3.5” Near-Line Hard Disk Drive (HDD) testing. It provides maximum throughput while minimizing factory floor space and power consumption. The system is designed to perform single insertion of SSW, BDSW and Burn-In as well as drive configuration. Using Saturn HD on the production floor will reduce drive build times, enable greater responsiveness to data center demands and lower test costs per HDD unit.
-
product
PCIe 2.0 Test Platform
PXP-100B
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
product
VPX Processing System
CRS-D4I-3VB1
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
