-
product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
785044-01
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
product
Pressure Measurement
A wide variety of pressure sensors with an option for nearly every pressure measurement application. Pressure transducers, pressure gauges, pressure switches manometers, calibrators, and regulators.
-
product
Dead Weight Pressure Tester
Unitech Scales And Measurements Pvt. Ltd
Dead Weight Pressure Gauge Tester is ideal for testing and calibration of pressure gauges,pressure transducers,recorders,digital calibrators etc. The system used in the dead weight is vertically mounted precision lapped piston and cylinder assembly with accurately calibrated mass for loading the piston. Pressure is built easily by single cylinder pump at very high rate. The whole system is housed inside a stainless steel case with elegant look. Pressure ports are provided to fix the gauges to be tested. Acrylic see-through oil tank is designed to use it as oil reservoir.
-
product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat...show more -
product
Shock & Drop Testing
Shock testing is often performed as part of a hardware qualification or design process. Information obtained during shock testing can improve the survivability of products as well as verify that they will perform properly in service. These types of tests require special transducers and measurement systems to record and process the high level, high frequency response.
-
product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
785045-01
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V,based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
product
Electrochemical (Molecular Electronic Transfer) Motion Sensor transducers
The Molecular Electronic Transfer Technology
The basic design of the MET transducer, shown in Figure 1. The transducer is contained in a channel, 1, of a sensor filled with a specially prepared electrolytic solution. It consists of four fine platinum mesh electrodes, two anodes, 2, and two cathodes, 3, separated by thin, microporous ceramic or polymer spacers 4. Such an assembly is held together by a housing 5. To measure the motion of the fluid, it must be converted into an electrical signal. One way of achieving this is by using the conv...show more -
product
ECHO 8 Ultrasonic Corrosion and Precision Thickness Gage
ECHO 8
Danatronics offers our newest ultrasonic precision thickness gage line, the ECHO 8 series. ECHO 8 represents our most advanced thickness gage ever combining dual and single element transducers all in one small package. ECHO 8 offers a 3.5” high resolution sunlight readable color display with live A-Scan, use of a wide variety of dual, contact, delay line and immersion transducers from 1-20 Mhz as default and custom created and stored applications setups, B-Scan, datalogger with up to 32GB of SD ...show more -
product
sbRIO-9425, Non-Enclosed, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
783950-01
Non-Enclosed, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The sbRIO‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The sbRIO‑9425 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
product
Power Analyzers
Real drive and test bench applicationMultiple power analyzer in one instrumentUltra flexible channel configurationWide range of fundamental frequencyCAN interface for automotive and test bench linkInternal current transducer supply and TEDS support
-
product
Pressure Indicators
Different types of single or dual channel pressure indicators are produced by DMA-Aero. The use of vibrating element transducers, combined with precise temperature measurements and humidity control provides near primary standard accuracy. With DMA-Aero software the pressure indicators can calibrate the DMA-Aero ADTS instruments automatically.
-
product
PXIe-4339, 25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
783531-01
25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4339 is a universal bridge input module ideal for test cell installations requiring both accuracy and flexibility. Completely configurable through software, each channel can take bridge-based measurements and direct voltage measurements. Eight input ranges in ratiometric mode and four in voltage mode accommodate a wide variety of sensor types for your changing application needs. The PXIe‑4339 also features per-channel wide bandwidth analog outputs, programmable excitation, Transducer Electronic Data Sheet (TEDS) support, and digital filtering.
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line...show more -
product
Servo type Accelerometer
A motion is sensed by a displacement detector, a current is fed to the coil to get back the pendulum mass to the original position. This current will be proportional to the acceleration, that is converted to an output voltage. The Servo type accelerometer is for the Earthquake Monitoring or measurements of micro tremor on the Civil Engineering Structures because of its higher sensitivity and stability or more accurate phase responses in the lower frequency range than those of other vibration transducers.
-
product
Ultrasonic Angle Beam Probes For Weld Seam Testing
SONOSCAN W
The ergonomic angle beam probes for Non-destructive Testing (NDT) from the SONOSCAN series inspect metals for cracks and inclusions. In the metal industry they are mainly used for weld seam testing. Our SONOSCAN probes are powerful, robust ultrasonic transducers which can be connected to all standard ultrasonic testing gauges.
-
product
Data Acquisition Conditioner
D4
The Model D4 Data Acquisition Conditioner is a portable, USB-powered precision instrument for use with resistive strain gages and strain gage-based transducers.
-
product
Millimeter Wave Orthomode Transducers
We are developing a series of millimeter wave orthomode transducers. These orthomode transducers are fullband, compact components. They achieve astounding cross-polarization while maintaining Micro Harmonics’ impressively low insertion loss.
-
product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
product
C Series Frequency Input Module
The C Series Frequency Input Module is designed to acquire isolated frequency inputs from magnetic pickup sensors, variable reluctance sensors, Hall effect sensors, and other transducers with a frequency output. Additionally, the C Series Frequency Input Module provides isolation, configurable thresholds, selectable filtering, and embedded counter measurement logic. These measurements can be synchronized with other frequency, analog, digital, and counter measurements in a single acquisition.
-
product
Torque Transducers
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
product
Short Leadtime Transducers
In addition to custom designs, we also have a carefully selected offering of transducers which can be ordered on a short lead-time.
-
product
Pressure Transducers and Pressure Transmitters
HBM Pressure Transducers are for use in hydraulic and pneumatic equipment, fluid-technology, chemical and process plants, air-conditioning equipment, the food industry, construction etc. Pressure measurement is a key application in many fields of industry. Pressure transducers and pressure transmitters from HBM ensure reliable and secure test results up to 15,000 bar.
-
product
Ultrasonic Dual Element Probes
SONOSCAN T
The ergonomic dual element probes for Non-Destructive Testing from the SONOSCAN Series comply with the DIN EN 12668-2 Standard and can be used to test metals, plastics and ceramics for imperfections such as cracks, inclusions, blowholes and other discontinuities. The transmitter-receiver probes manufactured in Germany are powerful, robust ultrasonic transducers which are compatible with the ultrasonic flaw detector SONOSCREEN ST10 or the thickness gauge SONOWALL 70.
-
product
Hydrophones
Operating principle of the hydrophones by ZETLAB Company is based on the piezo-electrical effect, which allows to use them as linear and reversible hydroacoustic transducers. The hydrophones by ZETLAB Company meet the requirements of sound environment non-distortion, wide frequency range, and non-directedness.
-
product
State, Event & Pulse Data Loggers
These data loggers can record rates from pulse output transducers, on/off or open close state changes or events.
-
product
Digital to LVDT-Digital to RVDT Converters
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices.
-
product
Lan-Xi Data Acquisition Hardware
Brüel & Kjær Sound & Vibration A/S
LAN-XI modules can function individually, and can use battery power to create small, rugged, low channel count systems of up to 12 channels. You can attach many different types of front input panels to connect the transducers of your choice. Around each connector is a circular LED that shows the channel's use and health at a glance backed up with an LCD screen. A key feature is the Dyn-X technology, which avoids the need for input ranging by using dual A/D converters to ensure you get the data the first time while achieving an effective dynamic range of over 160 dB.
-
product
Snowmobile Dynamometer
Standard dyno kit includes: 9" toroidal-flow water-brake absorber, electronic torque-arm transducer, engine load control, DYNOmite handheld data-acquisition computer with backlit LCD and keypad interface option, AC power supply, stainless-braided hoses, puller bolt, data wiring harness, and protective carrying case.
-
product
Combined Pressure and Temperature Transducers
Variohm offer some different styles of combined pressure and temperature transducers including the EPTT5100 which has an internal temperature sensor and the miniature EPTTE1400 which has an external temperature probe.