Powertek LLC

The Powertek product range is aimed at DC and AC power systems. Product capability includes a wide selection of power test measurement instruments and sensors for industrial process control, aerospace, transient data recording, appliance testing, power electronics, power conversion, motors, generators, testing EL Lamps - electro luminescent films, universities and colleges

  • +44 1788 519911
  • +44 870 0940135
  • info@powertekuk.com
  • 19 Cornwallis Road
    Bilton
    Warwickshire, Rugby CV22 7HL
    United Kingdom

Filter Results By:

Products

Applications

Showing recent results 1 - 15 of 23 products found.

  • Current Sensor

    IRF - Powertek LLC

    The robust IRF current probes all utilise a flexible clip on current sense coil, allowing fast and safe installation, ideal for current monitoring and retrospective fitting. Many of the current transformer safety considerations can be eliminated using this technique, which produces safe low level signals even with no secondary burden or loading.  

  • DC current Sensors

    CTH - Powertek LLC

    The CTH sensors convert dc current to an isolated voltage output, the CTHR sensors convert ac current to a dc output signal proportional to the Arms. All popular process control voltage and current loop outputs are available. Through hole or split core options mean that connection is non-intrusive and straightforward. The available input range of the CTH sensors is any value from 5A to 6000Adc.

  • Multifunction Calibrator 15 ppm basic accuracy

    MC142 - Powertek LLC

    Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.

  • Multifunction Voltage and Current Calibrator

    MC140i - Powertek LLC

    Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable

  • AC and DC Current or Voltage Transducers

    VT7 AND VT8 Series - Powertek LLC

    The Model VT7 Series dc voltage transducer produces an output which is directly proportional to the input from dc to 10kHz. It functions as a millivolt dc shunt or a high voltage isolator to 1000V

  • AC and DC non inductive current shunt

    Series A co-axial shunt and Option 02F/B shunt - Powertek LLC

    Use with wattmeters, DMMs and power analyzers to extend current measurement ranges. Use with phase angle meters to enable phase angle measurements between voltage and current. Ultra low phase shift

  • AC Current Sensor

    RCTi and RCTi 3ph - Powertek LLC

    The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.

  • Phase Angle Voltmeter

    PAV1010A - Powertek LLC

    Measuring Vrms, inphase, quadrature, freq, ratios and phase angles. Using Discrete Fourier Transform algorithms, the PAV1010A provides capability, performance and versatility not available with traditional PAVs. Targeted at the Synchro/Resolver and LVDT/RVDT marketplace, this instrument makes measurements of Phase Angle, In-Phase, Quadrature (90° component), Fundamental and Total Vrms very straightforward. All these measurements are displayed simultaneously on a bright multifunction display.

  • One Phase Electric Power/Energy Calibrator

    MC133 - Powertek LLC

    The MC133 master unit model is a one phase electric power/energy calibrator. It can supply the device under test with single phase precise voltage and current with calibrated phase shift along with DC voltage and current capability. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A. Simulated electric power can be set independently for each phase. Frequency can be set from 15Hz to 1 kHz with resolution 0.001Hz to 0.01Hz. The MC133 Calibrator is equipped with 5 1/2 digital DC meter with DC ranges 20mA or 10V for direct calibration of various types of power transducers and wattmeters.

  • Ultra Miniature Wideband Current Probe for AC Current Measurement

    CWT - Powertek LLC

    The CWT ULTRA Miniature current probes utilize a Rogowski Coil current sensor thin enough (typical cross section 1.7mm) to fit between the legs of a T0220 semiconductor switching device. With a high frequency bandwidth up to 30MHz, the CWT ULTRA miniature is ideal for measuring steady state current, switching transients or pulsed currents between 300mA and 6000Apk in power electronic equipment. The CWT ULTRA miniature probe is a clip around flexible coil current probe, based on the Rogowski principle to achieve high bandwidth measurement and faithful conversion of current to voltage, intended for use with oscilloscopes, transient recorders, data loggers, power meters and power analyzers. All models are supplied with an 80mm length clip-around coil, ensuring easy current monitoring even where access is limited.

  • Three-phase compact electric power/energy

    MC133C - Powertek LLC

    The Model MC133C is a compact single housed three phase electric power/energy calibrator. It can supply the device under test with precision one phase AC voltage and current with calibrated phase shift along with DC voltage and current. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A.

  • Three-phase Electric Power/energy Calibrator

    MC133Ci - Powertek LLC

    The MC133Ci model is a compact one-housing three phase electric power/energy calibrator. It can supply the device under test with one phase accurate AC voltage and current with calibrated phase shift or DC voltage and current. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A.

  • CALIBRATOR Multi Function Calibrator

    MC140 - Powertek LLC

    The Multifunction Calibrator MC140 functions as a Voltage Calibrator, Current Calibrator, Power Calibrator, Resistance Calibrator, Capacitance Calibrator and a Thermocouple Calibrator.? Having very low uncertainties, it is ideal as a standard of these electric quantities in calibration laboratories.

  • Flexible Current Sensor Probe

    CTA - Powertek LLC

    The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.

  • Flexible Rope-Type Current Probe

    RCT1A and RCT5A - Powertek LLC

    These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)