ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
-
Product
ADC DAC Module
ZET 220
-
ZET 220 ADC DAC module with 24-digit ADC converters is used for high-precision signals measurements in wide dynamic range. The signals to be measured are received from primary transducers – for instance, from sensors with 4-20 mA current output.
-
Product
ADC DAC Module
ZET 230
-
ZET 230 ADC DAC module is used for high-precision signal measurements in wide dynamic and frequency range. The module has an integrated anti-aliasing filters for 25 kHz. ZET 230 ADC DAC module is not designed for digital processing of constant level signals.
-
Product
ATE For ADC Module
MS 1527
-
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
Product
High Speed ADC > 10MSPS
-
Analog Devices high speed A/D converters (ADCs) offer the best performance and highest sampling speed in the market. The product offerings include high IF ADCs (10 MSPS to 125 MSPS), low IF ADCs (125 MSPS to 1 GSPS), integrated receivers, and wideband ADCs (>1 GSPS). The High speed ADC portfolio offers solutions for all high speed conversion applications.
-
Product
4-Channel ADC Module
FMC126
-
Sundance Multiprocessor Technology Ltd.
The FMC126 is a Quad-Channel Multi-Mode A/D FMC, fully compliant with VITA 57.1 Standards. The card provides four 10-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
Product
8 Channel 100 MS/s 16-bit ADC
SIS3302
-
The SIS3302 is the 16-bit extension to our 100 MS/s digitizer family. It is the 2nd DDR2 memory based digitizer unit in the SIS33xx family. The board is used for the readout of high resolution detectors, accelerator controls and other applications.
-
Product
Quad 3.1 Gsps, 14-bit ADC FMC+
ADF-Q3114
-
The ADF-Q3114 is a VITA 57.4 compliant FPGA Mezzanine Card (FMC+) that converts four channels of up to 3.1 GHz analog input bandwidth. This digitizer provides unparalleled analog-to-digital conversion capability with the PCIe/VME/ VXS/VPX carrier board of your choice. The ADF-Q3114 is designed to be compatible with AMD FPGA platforms.
-
Product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
-
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
Octal 310 Msps, 16-bit ADC FMC Module
ADF-O310
-
The ADF-O310 ADC FMC module from DEG delivers eight channels, each with 16 bits of resolution at a sample rate of up to 310 Msps. Utilizing the Analog Devices AD9652, the ADF-O310 enables defense applications requiring higher dynamic range, greater ENOB and wideband sampling performance.
-
Product
64 Channel 100 KHz 16 Bit ADC Module
DP-VXI-1101
-
DP-VXI-1101, the 16-bit, intelligent, 100KHz A / D converter module can be widely used in data acquisition applications requiring high speed scanning with 16-bit resolution and high accuracy of 0.01% of reading.The module occupies one slot in the VXI 'C' size mainframe.DP-VXI-1101 module uses 8 channel signal conditioner plug on modules(SCP) for accommodating various input signals. Eight such SCP modules can be plugged onto the main board to accommodate a maximum of 64 channels per A / D converter module.
-
Product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
-
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
Quad 12 Gsps 16-bit DAC& Dual 6 Gsps 12-bit ADC
ADF-QMx42
-
The DEG ADF-QMx42 FMC leverages the Analog Devices AD9082 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a dual 12-bit, 6 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx42 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and two receiver channels.
-
Product
10 Channel ADC FMC Module
ADCFN10-DC – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
2-Channel ADC Module
FMC161
-
Sundance Multiprocessor Technology Ltd.
The FMC161 provides one 12-bit A/D channel at 3.6Gsps or two A/D channels at 1.8Gsps clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC161 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
64 Channel ADC for VMEbus
VME392
-
The VME392 features 64 self-contained ADC channels with a resolution of either 12 or 16-bit (see ordering information). This product is ideally suited for mass acquisition with high accuracy for reasonable cost. The 64 channels are grouped into four sections of 16 channels each. Each section behaves completely independent from the other sections.
-
Product
Dual 3.0 Gsps, 14-bit ADC & Dual 3.0 Gsps, 16-bit DAC FMC
ADF-D3030
-
The ADF-D3030 FMC module from DEG is a dual channel ADC and dual channel DAC FMC module. The AD9208 ADC from ADI delivers 14 Bit resolution at sample rates of up to 3.1 Gsps. The DAC is an Analog Devices AD9174. This 16 Bit DAC device operates at 3.0 Gsps natively and up to 12.0 Gsps in interpolation mode.
-
Product
32 Channel ADC Module
DP-VME-1443
-
DP-VME-1443 is a VME-Based 32-Channel ADC module. It has 16-bit resolution and 5 micro seconds ( max) A/D conversion time. The module is optimised for wide variety of applications, which include checkout, data acquisition, military, naval, and aerospace systems.
-
Product
16 Channel ADC for CompactPCI
CPCI392
-
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
FMC-HPC ADC Board
FMC123
-
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
ADC Drivers Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
ADC 12-bit @ 2.6 GSPS and DAC 14-bit @ 5.6 GSPS, FMC
FMC216
-
The FMC216 is an FPGA Mezzanine Card (FMC) per VITA 57 specification. The FMC216 utilizes AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a DAC AD9129 providing 14-bit conversion rates of up to 5.6 GSPS. The analog input/output, digital output, clock and trigger interfaces of the FMC216 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
3U VPX Virtex-7 FPGA ADC/DAC
VPX3-530
-
Curtiss-Wright Defense Solutions
The VPX3-530 combines multiple channel high-speed ADCs and DACs with a latest generation user programmable Xilinx Virtex-7 FPGA in a range of rugged build formats for demanding applications such as SIGINT, radar and Software Defined Radio (SDR).
-
Product
ADC & DAC PCIe Card Powered by RFSoC
iW-RainboW-G42P®
-
AMD Xilinx’s ZU49/39/29DR Zynq Ultrascale+ RFSoCRAM Bandwidth8GB, 64bit DDR4-2400 RAM with ECC for PS8GB, 64bit DDR4-2666 RAM for PL (Expandable)16 DAC channels through SMA connector upto 10Gsps16 ADC channels through SMA connector upto 2.5Gsps3/4 Length PCIe Gen3 x8 Host InterfaceIntegrated ultra low-noise programmable RF PLIntegrated SyncE & PTP Network SynchronizationNVMe PCIe Gen2 x2/x4 M.2 ConnectorFMC+ HSPC Connector
-
Product
625 KHz Data Acquisition Multifunction (16 ADC, 2 DAC) PCMCIA W/T30 Cable & SRA-1
MF236/i(DAQi616MF)
-
The DAQi616MF is a type II PCMCIA I/O card for notebooks and other computers containing a PCMCIA slot.
-
Product
16 Bit 250 KS/s ADC With 16 Channel Multifunction Digital I/Board And Bridge Signal Conditioner
-
The CP246 is a single-width, 6U, CompactPCI/PXI module with 8 channels of Bridge Signal Conditioning feeding 8 independent 16-bit Analog to Digital Converters (ADC). This single-width solution incorporates both signal conditioning and ADC to eliminate the need for complex field wiring.
-
-
Product
Octal 4 Gsps 12-bit ADC
ADF-O4012
-
The DEG ADF-O4012 FMC includes eight 12-bit, 4 Gsps RF analog-to-digital converters (ADC). The ADF-O4012 features a 16-lane, 24.75 Gbps JESD204C interface, flexible clocking and triggering options. This ADF-O4012 leverages two Analog Devices AD9209 MxFE (Mixed Signal Front End) ICs, elevating the technology to a new level of integration.
-
Product
Low Power DC/DC Converters
-
The 4:1 Input Voltage 75 Watt WDE includes remote sensing, ultra-wide output voltage trim, and remote ON/ OFF. The digital power management enables increased reliability, configurability, voltage / current precision and fault management.
-
Product
Industrial Ethernet Embedded Switches
-
ADI’s portfolio of embedded Real Time Ethernet Switch are ideal solution for adding Industrial Ethernet connectivity to any field device or controller application. Designed for scalable and flexible system development, they support all major Industrial Ethernet Protocols while also providing the ability to future-proof for many Time Sensitive Networking (TSN) features, for the IEC/IEEE 60802 industrial profile. They interface easily with any host processor including any ARM® CPU utilizing the protocol specific device drivers provided by ADI. This provides the flexible system partitioning enabling the selection of processor that best fits your application requirements. It also provides the freedom to utilize any vendors protocol stack.
-
Product
Oscilloscopes
-
Is a type of electronic test instrument that allows observation of varying signal voltages, usually as a two-dimensional plot of one or more signals as a function of time. Other signals (such as sound or vibration) can be converted to voltages and displayed.
