Showing results: 466 - 480 of 486 items found.
-
VE series -
Ono Sokki
VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.
-
215 -
Elcometer Limited
Memory stores up to 260,000 readingsIdeal for testing for powder or liquid coatings in batch or conveyor ovensVariable measurement interval, date, time, °C / °FHigh temperature resistant teflon coated probe cables are easy to clean after each runQuick display shows maximum temperature, Cure-Index figure and pass/fail for each probeMeasure up to 6 different temperatures at one timeIdeal in situations where powder coated thickness is inconsistentStart and stop logging at a pre-set temperatureLarge menu-driven display for easy operationPrint full colour report directly to any HP printerUSB data output to ElcoMaster® software and combine with other key inspection measurements
-
IRIS Instruments
The Syscal Pro is an all-in-one multinode resistivity and induce polarization sounding and profiling system for environmental and engineering geophysical studies. The Syscal Pro gathers a 10 channels receiver and a 250 W internal transmitter which make it the more powerful system of the Syscal range. Compact, easy-to-use and field proof, the Syscal Pro measures both resistivity and chargeability. It is ideal for environmental and civil engineering applications such as depth-to-rock determination, weathered bedrock mapping. With a maximal output voltage of 2000Vpp, the Syscal Pro is very adapted to detect deep fault in fractured aquifers or to characterize the depths and thickness of the groundwater aquifers.
-
Keystone Compliance
Shielding effectiveness testing determines the ability of material to reduce the electromagnetic field in a space by blocking the field with barriers made of conductive and/or magnetic materials. Shielding effectiveness testing can be applied to a broad range of radio frequencies. Electromagnetic Shielding is typically applied to both enclosures and cables. The shielding can reduce the coupling or radio waves, electromagnetic fields and electrostatic fields. The amount of reduction can vary based on the material used, its thickness, the size of the shielded volume and the frequency of the fields of interest. Also impacting the effectiveness of the shielding is the size, shape and orientation or apertures in a shield to an incident electromagnetic field. Electromagnetic shielding that blocks radio frequency electromagnetic radiation is also known as RF Shielding.
-
ViTec Co. Ltd
The system for measuring and identifying aquatic organisms is designed to measure the linear dimensions and volume of live fish on a conveyor. The conveyor speed can reach 2.5 m / s, that is, up to 5 fish can pass through the installation in one second.The measurement of the thickness and volume of fish is carried out using a specialized camera Sick Ranger D40, which works on the principle of laser triangulation.The camera operation is synchronized with the conveyor movement using the Sick DGS-60 encoder.The industrial color camera Basler Scout scA1300-32gc is used for measuring the linear dimensions of fish (length and width), as well as highlighting characteristic features of different types (color of scales and fins) and possible defects.
-
IP-3000A -
Ono Sokki
IP-3000A Ignition pulse detector is a slim and light weighted detector by using amorphous metals fiber element. It is 1/4 in thickness (mass: approx. 1/50) and 1/3 in weight compared with the previous model of Ono Sokki. Also the IP-3000A can obtain constant output from low to high rotation with high sensitivity.Meeting the needs of structure or mechanism in recent gasoline engines, the IP-3000A can easily clamp around an ignition coil cable (the primary side cord of ignition coil or the current cord of electronic distributor). Moreover, heat-resistant design up to maximum operating temperature of +120 C° enables measurement under harsh environment.The IP-3000A Ignition pulse detector can be used with Ono Sokki’s engine tachometer.
-
Anderson Materials Evaluation, Inc.
Materials characterization, failure analysis, quality control, and materials and process development services are offered. Our analytical techniques allow us to assess elemental and chemical material composition, thermal properties, coating thickness, electrochemical properties, surface chemistry, surface wetting, corrosion rates and pitting potentials, contamination and degradation problems, metallography, fractography, phase transitions, static coefficient of friction, adhesive bonding strength and causes of adhesive bonding failures, surface tension and surface energy, tensile and compressive strength, bend deflection, lapshear strength, elasticity properties, UV and visible light absorption and reflection, density and porosity, and many other material properties integral to improving your products.
-
Model 2180 -
Magnetic Instrumentation Inc.
The unit is compact and lightweight. The basic system is 7″ wide by 2.5″ high and 12″ long. When measurements are needed below approximately 100 micro-ohm-centimeters, the basic system is piggybacked onto a second enclosure that houses a power amplifier with a current gain of ten. The combined unit measures 7″ wide by 5″ high and 12″ long. The combined unit weighs 11.5 pounds. Two short cables interconnect the two enclosures for powering the power amplifier and routing the signals to the fixture or four point probe. The front panel of the basic system includes a 32-character backlit LCD display and a set of function keys. An easy-to-use menu will allow access to user defined parameters such as sample thickness, sample volume, and calibration constants; upper and lower alarm limits, relative measurements, and several others.
-
Shenzhen Graigar Technology Co.,Ltd.
Electrochemical (fuel cell) alcohol sensor, Module changeable Test Range: 0.000-2.000mg/l (0.400%B.A.C; 4.000%oB.A.C; 4.000g/l;) Alarming level: Pass level: 0.090mg/L (could be modified) Fail level:0.250mg/L (could be modified) Accuracy: +/-10% Work temperature: -10oC-50oC Work humidity: <95%RH (No Dews) Battery: 2XAA NiMH batteries, rating capacity: 2.1AH Dimension lXbXh: (mm) 250X105X400 Indication manner: mg/l,mg/100ml,g/l ,%BAC,%oBAC optional Coin for single time: 0-15 (For 0, the tester can be tested without coin). Coin diameter: 20mm-28mm Coin thickness: 1.2mm-2.5mm Coins Capacity: about 200 pieces Straw capacity: 200pcs(⊄<=7mm) Breath sampling time: about 5 seconds continuous breath.
-
ASTM D149 -
National Technical Systems
This test method covers procedures for the determination of dielectric strength of solid insulating materials at commercial power frequencies, under specified conditions. Unless otherwise specified, the tests shall be made at 60 Hz. However, this test method is suitable for use at any frequency from 25 to 800 Hz. At frequencies above 800 Hz, dielectric heating is a potential problem. This test method is intended to be used in conjunction with any ASTM standard or other document that refers to this test method. References to this document need to specify the particular options to be used. It is suitable for use at various temperatures, and in any suitable gaseous or liquid surrounding medium. This test method is not intended for measuring the dielectric strength of materials that are fluid under the conditions of test. This test method is not intended for use in determining intrinsic dielectric strength, direct-voltage dielectric strength, or thermal failure under electrical stress (see Test Method ASTM D3151). This test method is most commonly used to determine the dielectric breakdown voltage through the thickness of a test specimen (puncture). It is also suitable for use to determine dielectric breakdown voltage along the interface between a solid specimen and a gaseous or liquid surrounding medium (flashover). This test method is similar to IEC Publication 243-1. All procedures in this method are included in IEC 243-1. Differences between this method and IEC 243-1 are largely editorial. Note: The above information is taken directly from the test method Scope published in ASTM D149.
-
KLA-Tencor Corp
KLA’s substrate manufacturing portfolio includes defect inspection and review, metrology and data management systems that help substrate manufacturers manage quality throughout the wafer fabrication process. Specialized wafer inspection and review tools assess wafer surface quality and detect, count and bin defects during production and as a critical part of outgoing wafer qualification. Wafer geometry systems ensure the wafer shape is extremely flat and uniform in thickness, with precisely controlled wafer shape topography. Data analysis and management systems proactively identify substrate fabrication process excursions that can lead to yield loss. KLA’s substrate manufacturing systems support process development, production monitoring and final quality check of a broad range of substrate types and sizes including silicon, prime silicon, SOI, sapphire, glass, GaAs, SiC, GaN, InP, GaSb, Ge, LiTaO3, LiNBO3, and epitaxial wafers.
-
Dongguan Amade Instruments Technology Co., Ltd
Packaging testing equipment are intended to measure the resistance of corrugated containers to various crushes and burst at given conditions, applied to bursting strength test, ring crush test, edge crush test, flat crush test, pin adhesion test, puncture strength test, bending stiffness test, corrugating medium test, compression test, damp-proof test etc. As corrugated boxes assume the important responsibility of loading and protecting goods playing an inevitable role in modern logistics, so the properties of corrugated boards have to be mastered by manufacturers and users prior to use. The physical performances which are measured by a series of testings are core factors for judging the quality of packaging boxes. Paper testing items mainly include quantification, thickness measurement, whiteness, smoothness,breaking elongation, burst resistance, folding resistance, stiffness, tearability, degree of sizing, etc.
-
NEX LS -
Applied Rigaku Technologies, Inc
Featuring advanced third generation EDXRF technology, the Rigaku NEX LS represents the next evolution of scanning multi-element process coatings analyzers for web or coil applications. To deliver superior analytical performance and reliability, the EDXRF measuring head assembly was derived from the established Rigaku NEX Series high-resolution benchtop instrumentation. With this proven technology, the Rigaku NEX LS delivers rapid, non-destructive, multi-element analyses — for coat weight, coating thickness and/or composition — for elements from aluminum (Al) through uranium (U). The measuring head is mounted on a rigid beam and is equipped with a linear traversing mechanism positioned over a roller so that the head-to-surface distance is constant. Common applications include silicone release coaters, converters, denesting Si for vacuum-formed plastics, RoHS compliance, conversion coatings, metalized plastic, top coatings on metal coil and fire retardants on fabric.
-
NovoTest
The UCI hardness measuring method complies to ASTM A1038.The ultrasonic contact impedance (UCI) probe is purposed to be used for hardness measuring in the case of the testing area minimal thickness (from 1 mm), objects of complex surface shape, and for measuring surface hardened layers hardness.This method is very fast and easy: place the probe on the tested object surface, press the probe with the required effort to the surface and save the hardness value, shown on the display of the device. Small size diamond indenter allows measuring hardness value of all items, which are thicker than 1 mm. The UCI method of hardness testing is the least destructive because the hardness tester NOVOTEST T-UD3 with UCI probe leaves much smaller prints (imprints) than the majority of bench hardness tester would. That’s why a portable hardness tester with UCI probe is the best choice.
-
Elcometer Limited
*Oven Logger set up & programming*Paint/Powder parameter library*Product probe maps*Fully customisable inspection templates*Selectable probe/channel traces*Statistical analysis by probe/channel*Max, Min, standard deviation, coefficient of variation*Temperature profile, cure progress, histogram & individual cure value graphs against product*Time at temperature, time of peak difference*Time above maximum absolute & minimum cross link temperatures*Fully customisable inspection reports*Combined reports - coating thickness, gloss, adhesion, profile, climate, surface cleanliness*Report generator wizard & PDF generator*Email or export data*Import photo’s, data sheets, critical data, inspection notes, etc & include on inspection reports*Cloud computing - allows for cross site collaboration, including internal text messaging tool*Overlay temperature profiles, review and compare multiple oven profiles over time*Use additional data loggers for multiple channels or run overlays
