- Pickering Interfaces Inc.
product
LXI WTB Extender
60-984-001
The 60-894 provides a simple an effective method of joining two LXI WTB bus cables together to extend the length of available cables. It is an ideal solution for cable extension where users need to experiment with different cabling solutions without having to totally replace the cables in the system. The 60-894 provides mating connectors for the WTB on each end connected together by a set of accurate differential transmission lines to avoid additional reflections on the cable. The 60-894 is entirely passive and is compatible with the LXI specification.
-
product
High Impedance Active Probes
7
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
product
TXRF Spectrometers
Total reflection X-ray fluorescence spectrometry (TXRF) is a well-established method for trace element analysis on a variety of samples.
-
product
Forced Air Cooled RF Coaxial Loads
86700 Series
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
product
Sensors
A speed and angle sensor using a black/white tape which is glued on a rotating part. The reflection is converted into a TTL signal, bandwidth 100 kHz. The sensor consists of a tiny electronics part and a 5 m fiber optic cable terminated with a M6 screw. Thus areas where space is very limited still can be reached conveniently.
-
product
High Voltage 50 Ω Pulse Generator
TLP-12010A
High Power Pulse Instruments GmbH
- High pulse output current up to ±120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical 300 ps rise time- Wafer, package and system level TLP and HMM testing- 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 digital programmable pulse rise times out of: 300 ps to 50 ns (optional)- 1 built-in pulse width: 100 ns- Optional external p...show more -
product
PXI-2597, 26.5 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
778572-97
26.5 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2597 is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. The internal termination of the PXI‑2597 helps prevent high-power reflections that arise from open channels on the module. You can use the PXI‑2597 onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
TXRF Spectrometers
Total reflection X-ray fluorescence spectrometry (TXRF) is a well-established method for trace element analysis on a variety of samples.
-
product
Transition Time Converter, 150ps
15435A
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters.Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications.The converters are fitted with SMA connectors, one male, one female.
-
product
cPCI 3U RA & LA
Hartmann Electronic’s cPCI 3U RA Series features a sleek board design based on High Speed Design concept with exceptionally low-level reflection. The featured reflection levels are achieved by means of uniform signal surge impedance.
-
product
Dual-Directional Couplers
KRYTAR’s directional couplers are uniquely designed for systems applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. These couplers provide simple solutions for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted applications the compact size makes KRYTAR directional couplers ideal solutions.
-
product
Polarization Conditioners
High-speed software controlled polarization control and polarization scrambling with broad wavelength coverage, low insertion loss and back reflection.
-
product
Transition Time Converters
These converters have been designed to convert the transition times of instruments with fixed, fast transition times, to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns); hence reducing the signal bandwidth. All transition-times are between 10% and 90% of amplitude.The design of these converters ensures very low signal reflection far beyond the 3 dB point. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with two SMA connectors, one male, one female.
-
product
Oil In Water/Soil Analyzer
InfraCal 2 ATR-SP
The InfraCal Model ATR-SP is recommended for measuring oil in water, TPH in soil or FOG in wastewater concentration levels when using hexane, pentane or Vertrel MCA as the extracting solvent. Measurement data obtained with this analyzer will correlate to EPA Method 1664 as both procedures are based on evaporation techniques and measuring the residual oil and grease. The analyzer is equipped with a built-in cubic zirconia horizontal attenuated total reflection (HATR) stainless steel sample stage. The InfraCal 2 ATR-SP is a direct replacement for the original InfraCal HATR-T2 used worldwide for the determination of TOG/TPH in water and soil.
-
product
Optical Detector
LG-9200
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
product
Thermal Night Vision
Zhejiang ULIRvisionTechnology Co., LTD
The infrared thermal night vision system is mainly used in the dark environment without visible light or low light. The infrared emitting device actively projects the infrared light onto the object, and the infrared light is reflected by the object and enters the lens for imaging. The image is formed by the reflection of infrared light instead of visible light. At this time, you can see the picture that is invisible to the naked eye in the dark environment.
-
product
Individual Optical Filters
Our comprehensive line of Semrock optical filters helps your design attain the best signal-to-noise ratios. Steep spectral edges maximize useable bandwidth, and high transmission or reflection captures the brightest images with best-in-class Flatness. Deep and extended blocking are optimized for your application, minimizing background and crosstalk while reducing cost. Select from the extensive catalog or go with a custom filter to your exact specifications, and remain confident of uncompromising quality, reliability, and reproducible results.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
product
RF Bridge, 50 Ohm, 300 kHz to 3 GHz
86205B
The Keysight 86205B high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
product
Digital Tachometer
TAC-L
Model TAC-L Portable Digital Tachometer measures rotational speed either by contacting a rotatable head to the shaft of the object, or using photo sensor to detect the reflections from the laser. The laser target can record from a distance of up to 20 inches and gives a more accurate measurement than LED targeting. Model TAC-L includes a large LCD with a backlight for use in dark areas.
-
product
Epi Thickness & Composition System
Element
The Element system is the tool of record for wafer suppliers for high speed impurity mapping and epi thickness measurement. It is the only tool on the market with the unique combination of transmission and reflection based technology. This system is the industry standard for dielectric monitoring.
-
product
PXI-2555, 2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-55
2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2555 is an RF signal multiplexer switch module. The internal termination of the PXI‑2555, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in video RF applications where such reflections can damage the source. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
DCA-X Sampling Oscilloscopes
The DCA-X wide-bandwidth sampling oscilloscopes are in our digital communication analyzer (DCA) family. These are modular platforms that provide accurate and precise measurements of high-speed digital designs from 50 Mb/s to 224 Gb/s. You can configure the DCA-X mainframes by selecting from a variety of plug-in modules that perform precision optical, electrical, and time domain reflection / transmission (TDR / TDT) measurements. Select specific modules to obtain the desired bandwidth, filtering, and sensitivity that match your measurement needs.
-
product
Wall Measurement Thickness Gauge Wall Thickness Test Instrument
HS160
Shenzhen Chuangxin Instruments Co., Ltd.
HS160 Wall measurement thickness gauge, wall thickness measuring equipment apply to measure the thickness of all kinds of material, through which the ultrasonic wave can propagate at a constant speed and can get reflection from the back. This instrument can be used for a variety of plate and all kinds of machining parts for accurate measurement. Another important function of this gauge is to monitor all kinds of pipelines and pressure vessels used in the production equipment, monitoring their degree of corroded thinning during the using process. It's widely used in petroleum, chemical industry, metallurgy, shipbuilding, aviation, aerospace and other fields.
-
product
Amplifier-separated Type Digital Laser Sensor
LS-500
Panasonic Industrial Devices Sales Company of America
The LS-500 Series Amplifier-Separated Type Digital Laser Sensor offers high-class Laser Sensors able to detect very small objects with a processing speed of down to 60µs. The new full stainless steel M6 housing is robust and optimally suited for applications in harsh environments. The unique controller can handle Thru-Beam, Diffuse Reflection and Retroreflection Laser Sensor heads. All Sensors are equipped with two digital outputs, and cable-type Sensors offer an additional analog output, opening new dimensions in the detection of small objects.
-
product
1310/1550 nm Dual Laser Source Back Reflectiom/Power Meter
GM8019 + GM83001E
The UC INSTRUMENTS GM8019 + GM83001E 1310/1550 nm dual laser source back reflection meter and power meter is a compact, direct display instrument for the convinent measurement of backreflection, insertion loss and power connector, fiber optic components, and system. With a single output port, the meter is very easy to use and ideal for fiber cable jumper manufacturers.
-
product
photon3D
Innovative 3D cameras from Photonfocus offer completely new possibilities for future-oriented laser triangulation applications. The photon3D platform is optimized for high frame rates and high sensitivity and offers robust algorithms for determining the laser line in the FPGA of the camera. Photonfocus has optimized these algorithms in order to suppress artifacts such as reflections.
-
product
Fixed Attenuator
FAXE
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
product
Automatic Tuners10MHz – 140GHz
Load Pull
An impedance tuner is an apparatus, which generates controllable reflection factor (Impedance) over a certain frequency range.
-
product
PIM & Return Loss Measurement
Range to Fault (RTF)
Range To Fault (RTF) is an exciting new technology from Kaelus that enables operators to accurately measure the location of PIM and Return Loss faults in their RF infrastructure. Reflection data together with PIM data provides an unmatched level of clarity for identifying the location of faults in the RF path.
-
product
Sparse Nodal Solution
MicrOBS
MicrOBSNT is an ocean bottom node solution for seismic refraction and reflection surveys.