Reflection
-
Product
Power Cable Fault Locator
TM500
-
TM500 Power Cable Fault Locator adopts international advanced electronic testing technologies and SCM technology, and combines low-voltage pulse reflection and pulse current testing methods, is suitable for the precise range finding of power cable high resistance, flashover, disconnection, and low resistance. Low-voltage pulse reflection method applies to test the range of the low resistance and broken line, and the length and wave velocity of various cables. Pulse current testing method can be divided into breakthrough high-voltage flashover and DC high-voltage flashover for the high resistance and flashover cable fault finding.
-
Product
Cassegrain Antennas
-
In telecommunications and radar, a Cassegrain antenna is a parabolic antenna in which the feed antenna is mounted at or behind the surface of the concave main parabolic reflector dish and is aimed at a smaller convex secondary reflector suspended in front of the primary reflector. The beam of radio waves from the feed illuminates the secondary reflector, which reflects it back to the main reflector dish, which reflects it forward again to form the desired beam. The Cassegrain design is widely used in parabolic antennas, particularly in large antennas such as those in satellite ground stations, radio telescopes, and communication satellites.
-
Product
SINE FBI Charts
-
There are two SINE Sinusoidal arrays designed for FBI applications: the SINE M-13-60-S-RM and the SINE M-13-60-FBI Kit.The SINE M-13-60-S-RM was designed jointly by the Federal Bureau of Investigation, of Washington DC, and MITRE, of Bedford MA. The primary function of this Target is for computing Modulation Transfer Function (MTF) evaluation in live scanner fingerprint systems for conformance to Integrated Automated Fingerprint Identification Systems (AFIS) image quality requirements. The array is on reflective material measuring 16mm x 16mm with sinusoidal arrays ranging in frequency from 1.0 to 10.0 cycles per mm; with nominal modulation of the sinusoidal areas at 60%. The top and bottom rows are density scales, from 0.20 to 1.20 densities.The SINE M-13-60-FBI Kit consist of two individual components, the SINE M-13-60-1X-RM and the RR1-N-RM Ronchi Ruling grating.
-
Product
Launch Fiber Box
-
OTDR measuring devices are used in various ways in fibre optic technology. They enable extensive characterisation of existing fibre optic cabling networks. The use of launch and receive fibres is advantageous when it comes to ensuring precise results evaluations. With bidirectional backscatter measurements with launch and receive fibres, the attenuation values of the first and last plug-in connection can be determined precisely by averaging and device dead zones can be avoided. Measuring device manufacturers recommend different lengths of launch and receives fibres to avoid “phantom reflections”. These launch and receive fibres are also subject to measuring equipment monitoring and should regularly undergo revision in accordance with the OTDR measuring devices. A good measurement result depends on the state and quality of the measuring equipment used. Diamond offers various types of launch and receive fibres, one with standard telecommunications connectors and the other with an outdoor connector for harsh environments.
-
Product
Sparse Nodal Solution
MicrOBS
-
MicrOBSNT is an ocean bottom node solution for seismic refraction and reflection surveys.
-
Product
Power Supplies
CUL-950B
-
The CUL-series is a semi-modular power supply that lets you select the cables you need while powering your gaming system with a 140mm Blue LED cooling fan and 6 pin PCI-E ready. **850W & 950W is offering 140mm Blue LED cooling fan & Dual 6+2 PCI-E ready. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power & 4+4 pin CPU connector are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
Plus Series Spectrum Analyzers
SSA3000X
-
The SIGLENT SSA3000X Plus series spectrum analyzers are powerful and flexible tools for RF signal and network analysis. With a frequency range up to 7.5 GHz, the analyzer delivers reliable automatic measurements and multiple modes of operation: spectrum analyzer the base, optional functions include RF power measurement, vector signal modulation analysis, reflection measurement, and EMI test.
-
Product
Spectrally Flat Class B Albedometer
LPPYRA05
-
Albedometers are composed of two pyranometers that are mounted back-to-back. An albedometer measures in two directions; one pyranometer is facing upwards (measuring the global solar radiation), the other pyranometer is facing downwards (measuring the reflected solar radiation).
-
Product
Optical Detector
LG-9200
-
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
Product
High Frequency Chambers
-
Specialized, shielded rooms designed to absorb electromagnetic reflections.
-
Product
Non-contact Optical Surface Profiler
VS-OSP
-
The VersaSCAN OSP integrates the Base with a high-accuracy, high-speed laser displacement sensor. The OSP technique uses diffuse reflection mechanism to measure topography of a sample. OSP can be used to measure topography, as a very sensitive leveling mechanism, or charting topography to be implemented with other scanning probe techniques for constant-distance mode operation.
-
Product
cPCI 3U RB
-
Hartmann’s cPCI 3U RB Series Backplanes utilize a board design based on the HIGH-SPEED DESIGN concept. Low reflection is achieved by means of uniform signal surge impedance.
-
Product
Laser Distance Meters
-
GAOTek’s laser distance meters are used to measure the distance between the target and the device. Our device sends a pulse of laser light to the target and measures the time it takes for the reflection to return. Its ergonomic design emphasizes function and user-friendly usage. GAOTek’s laser distance meters are reliable, of high quality, and affordable instruments that provide an accurate measuring. Our products offer an easier inspection or testing experience, is compact, and portable. A laser distance meter offers efficient testing, accuracy, versatility, safety, functionality, and convenience compared to the old-fashioned tape method when used in the field. Our laser distance meters are available for purchase to the United States, Canada and globally.
-
Product
Collimators
-
Collimators are optical systems used to imitate standard targets placed in "optical infinity" (very long distance). The collimators are used for projection of image of reference targets into direction of tested imagers. According to type of optical elements used in design, collimators are divided into two groups: reflective collimators and refractive collimators. Reflective collimators due to their wide spectral range are almost exclusively used in systems for testing thermal imagers and are also preferable in systems testing TV cameras, SWIR imagers, laser systems or multi-sensor surveillance systems. Refractive collimators are mostly used in systems for testing night vision devices or TV cameras working in visible/near infrared range.
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
Forced Air Cooled RF Coaxial Loads
86700 Series
-
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
Product
Active Peak Reading Wattmeter
HF/6
-
Active peak reading wattmeter with simultaneously variable hold time on both the forward and reflected meter movements. This variable delay can be adjusted for quick action for high speed CW, or for longer periods more appropriate for the display of SSB and AM voice peaks. The peak detectors sport a new fast attack design capable of capturing quick pulses such as a single dit. Beautiful industrial design with tri color meter scale and brilliant LED illumination make the DWM series wattmeter a beautiful addition to any station.
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
Product
Network OTDR
NFO series
-
The NFO OTDR unit injects the laser pulse into the fiber under test and picks up scattered and reflected optical signals by an avalanche photodiode (APD). The unit accepts remote commands from Internet to control all related timing and data acquisition processes. Maximal three wavelengths are available at the NFO with options on 1310, 1490, 1550, and 1625 nm. NFO also has options on dynamic ranges so users can select the most cost effective units for their demands. Radiantech provides an easy use API (Application Program Interface) for NFO so users can design and build their own AP for NFO. Standard NFO API package is for Windows XP or higher. Please contact Radiantech’s sales person to inquire API for another OS.
-
Product
SiTek Standard PSD
1L20_CP3
-
The SiTek Standard PSD (Position Sensing Detector) has high resolution, fast response and outstanding linearity. It is used in a wide variety of applications, most of them utilizing light sources in the visible or near-infrared part of the spectrum. The spectral range covers the region 400 - 1100 nm. Thanks to SiTek's proprietary AR-coating, optimized around 860 nm, a reflection loss of only 2% is achieved around the responsivity peak. Most of the detectors have a cover window to avoid handling damages.
-
Product
PHOTOELECT Sensor
PE1
-
● Easy installation, high-speed pulse generator, high-speed rotation control, and more.● A wealth of models ideal for limit control, counting control, and other applications.● Sensing distance of 5~100cm for Diffuse reflective models, 1M~3M for Retro reflective models and 10M~20M for Through beam models.● Housing by PBT with strong structure and acid resisting or Copper with Nickel-plating available.
-
Product
Coaxial Short
85140A
Terminator
The Keysight 85140A coaxial short is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm male connector.
-
Product
Haze Meter
HAM-02
-
Jinan Leading Instruments Co., Ltd.
HAM-02 Haze Meter is a kind of small hazer meter designed according to ASTMD1003—61(1997). It is applying to test the light transmittance,transmission haze, and reflection haze, reflectivity of transparent and semitransparent parallel level material and plasticfilms. Also it is suitable for liquid samples (water, beverage, pharmacy,colored liquid, grease) turbidity measurement. It is the basic instrument for plastic, glass products, all kinds oftransparent packaging films, colored and colorless of organic glass andaerospace, automotive glass and photographic film.
-
Product
Variable Fiber Optic Attenuator
-
Variable fiber optic attenuator could help simulate distance or actual attenuation in the fiber optic testing work by inserting a calibrated attenuation into the link. By using the variable fiber optic attenuator, technicians could verify the power margin received by testing the fiber optic link power budget. Variable fiber attenuator can help user vary the light power injected from a light source into the optical fiber. Important parameter of variable fiber attenuator include its insertion loss, reflection loss and attenuation range.
-
Product
Instrumentation Tutor
-
Unitech Scales And Measurements Pvt. Ltd
This comprises of temperature and speed using different methods. RTD, thermistor and thermocouple are used as sensors with digital temperature indicator to measure temperature. A small water kettle is supplied as a temperature source upto 100°C. Glass bead thermometer is used as standard temperature measurement source to conduct the experiment. Magnetic and photo reflective sensors are used to measure speed. A FHP motor with speed regulator is used as speed source. To the shaft 60 teeth tone wheels are fixed to generate pulses.
-
Product
RF Limiter, 10 Hz to 1800 MHz
11867A
-
11867A RF limiter can be used to protect the input circuits of spectrum analyzers, counters, amplifiers, and other instruments from high power levels with minimal effect on measurement performance. This limiter (10 Hzto 1800 MHz) reflects signals up to 10 watts average power and 100 watts peak power. Insertion loss is less than 0.75 dB.
-
Product
PXI-2597, 26.5 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
778572-97
RF Multiplexer
26.5 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2597 is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. The internal termination of the PXI‑2597 helps prevent high-power reflections that arise from open channels on the module. You can use the PXI‑2597 onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
