Showing results: 466 - 480 of 544 items found.
-
EXpress -
DSI International
eXpress is a comprehensive model-based diagnostics engineering software application providing an environment for the design, capture, integration, evaluation and optimization of complex or large-scale system diagnostics, prognostics health management (PHM), systems testability engineering, failure mode and effects analysis and system safety analysis. eXpress is uniquely suited to influence the diagnostic development for new designs or to exploit the diagnostic challenges of existing legacy systems. Its robust structure facilitates the capture of extensive interdisciplinary design knowledge providing an unmatched ability to corroborate, reuse and re-purpose expert knowledge in performing standardised testability, reliability and maintainability analyses.
-
Windrock On-Guard -
Windrock, Inc.
Windrock On-Guard™ and Platinum online monitoring systems employ permanently installed transducers and local signal conditioning to provide continuous measurement of machinery condition and performance. On-Guard™ and Platinum systems are specifically designed for reciprocating engines and compressors and protect these assets against catastrophic failure by providing critical parameter values, along with associated alarms to machinery control systems. Modular construction allows the Windrock to design a system that meets your needs and objectives. Your local representative will be pleased to assist in specifying which On-Guard™ modules and Platinum systems best meets your application needs.
-
AutoSIR2™ -
Gen3 Systems Limited
One AutoSIR chassis can hold between 1 to 16 measurement cards and can monitor up to 256 x 2-point test patterns or 78 x 5-point test patterns, or 32 x 9-point test patterns at selectable intervals from minutes to days. Each channel is current limited (1 M Ω), ensuring that dendrites are preserved for failure analysis. The frequent monitoring capability provides a full picture of the electrochemical reactions taking place on a circuit assembly, and provides early trend analysis enabling tests to be curtailed, thus saving considerable test time and money.
-
VTC SERIES -
EMIC Corporation
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
DSX CableAnalyzer™ Series -
Fluke Networks
The DSX CableAnalyzer Series copper test solution enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you'll be. Unfortunately, there are a lot of things that slow the process down setting up the tester incorrectly, testing to the wrong limits, waiting for skilled technicians to analyze and troubleshoot failures, misinterpretation of results, and producing test reports that customers cannot understand.
-
Polaris Networks
LBS Tester provides an end-to-end test bed for Mobile Network Operators and Network Equipment Manufacturers, to verify the accurate implementation of the location services network. The LBS Tester tests that the Location Server (System Under Test) is correctly executing the positioning procedures over the control plane and/or user plane of that network. To test normal signaling, or failure scenarios, over the LTE User Plane as the number of SETs (SUPL Enabled Terminals) simulated by the LBS Tester increases, the Location Server must execute LPP (Location Positioning Protocol) procedures over SUPL (Secure User Plane Protocol) with success, or without, respectively.
-
XLR Sniffer/Sender -
Sound Tools
Designed by Rat Sound to deal with the "real world" of pro audio, the SoundTools Sniffer/Senders are the perfect tools for live environments. Test snake lines and cables when the ends are at a distance and avoid running extra cables just to test. Utilizing phantom power the Sniffer end can quickly test snake lines in minutes. The aluminum barrels eliminates the problem many testers face with solder joints failures and the unit will never rust. 3 simple LED’s will instantly diagnosis your cable as it tests for every possible shot, open, or cross wire in XLR cables. If the LED’s read all green you cable will work!
-
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 980 HDMI Phy & Protocol Aux Channel Analyzer module supports compliance testing of the HDMI DDC bus and HDMI 2.0 CEC testing (partial support only). The module’s CEC compliance tests enable you to identify compliance failures early in the development cycle. The solution is ideal for pre-testing and self-testing (where permitted) your HDMI 2.0 device. The module also supports compliance testing of the HDMI DDC bus voltage and timing parameters in accordance with HDMI 1.4b. Future releases of the module will support functional tests and compliance tests on other HDMI auxiliary channels.
-
CA-RD(H) -
Cincinnati Sub-Zero Products
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
PP-TOFMS -
HORIBA, Ltd.
Plasma Profiling TOFMS addresses the needs of materials scientists across a wide range of application areas. PP-TOFMS provides fast elemental depth distribution of any inorganic material. The speed and ease of use of PP-TOFMS permit to reduce optimization time of growth processes as many research scientists strive to reduce the time from discovery to applications of new materials.The simultaneous full coverage of TOFMS available for each point of depth permits the detection of non suspected contamination. This is key for failure analysis and optimization of thin film processes that tend to no longer be based on ultra-high grade methods (i.e. ink jet printing…).
-
IVA® MODEL 210S -
Oneida Research Services, Inc
The IVA® system is specifically designed for the quantitative analysis of low molecular weight gases contained in hermetic packages, cavities and other enclosures. The Model 210s concept integrates automated hardware with easy-to-use icon-driven software. Its design permits routine quality control, failure analysis and research level testing operation as a turn-key analytical system. The IVA® Model 210s includes a high-performance, quadrupole-mass spectrometer analyzer, a sample-mounting interface and precision hardware. The instrument is also computer-controlled and equipped with exclusive ORS integrated system control software — which provides instrument control, data analysis, data archiving and ease of operation.
-
IPMT-3 -
FM SYSTEMS, INC.
The IPMT-3 is a precision attenuator used to test IP video systems to insure that you have an adequate digital signal margin. Digital signal margin is the amount of signal level above the digital cliff that you have in your system to prevent a picture failure from occurring. IP cameras will give you a perfect picture until the network cable loss reaches beyond the minimum allowable signal level and then you suddenly get no picture at all. This effect is called the digital cliff, because like walking off of a cliff, everything is great till you take the last step off the edge and then all is lost.
-
WECO 9000 -
Radian Research, Inc.
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
National Technical Systems
Surface Insulation Resistance (SIR), as defined by IPC, is the electrical resistance of an insulating material between a pair of contacts, conductors, or grounding devices that is determined under specified environmental and electrical conditions.In respect to the world of printed circuit boards (PCBs) and printed circuit assemblies (PCAs), SIR testing—also commonly referred to as Temperature Humidity Bias (THB) testing—is used to evaluate a product’s or a process’ ability to resist “failure” by means of current leakage or an electrical short (i.e., dendritic growth). SIR testing is typically performed under elevated temperature and humidity conditions—such as 85°C/85% RH and 40°C/90%—with periodic insulation resistance (IR) measurements obtained.
-
4012 -
Barth Electronics, Inc
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
