-
Product
Photodiode Burn-in Reliability Test System
58606
-
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
-
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
-
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
BSD (Test Diagnostics)
-
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
Product
Functional Test
UTS
-
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
Product
Test Management Software
ActivATE™
-
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
-
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
-
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
Standard Test Systems
WaveCore™ Products
-
Textron Systems’ WaveCore family offers a variety of standard test systems with a primary application of satellite payload lab testing. Our systems can be deployed affordably for both production and engineering applications, providing industry-leading levels of data correlation with high system mean time between failures and low mean time to repair.
-
Product
SAS Protocol Test System
Sierra M124A
-
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
LTE RRM Test System
T4010S
-
The T4020S LTE RRM tester is the Keysight platform for LTE RRM conformance testing of LTE UEs. T4020S belongs to the Keysight LTE product family and, as the other LTE T4000S test platforms, is based on the T2010A LTE Wireless Communications Test Set.
-
Product
NFC Conformance Test System
T3111S
-
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
Product
6TL60 Rotary Test Handler
H79006010
-
6TL60 has been designed according to the 6TL philosophy, following the concepts of flexibility, modularity and scalability, and with the aim of improving production efficiency as well as increase production capacity and reduce costs.The 6TL60 is the best production solution to automate test processes to reduce the cycle time and the footprint used in the manufacturing plan
-
Product
Functional Test
cUTS
-
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
Product
Mini LED Backlight Module Automatic Optical Test System
7661-K003
-
Chroma 7661-K003 Mini LED Backlight Module Automatic Optical Test System contains a 71803-2 2D color analyzer to measure chromaticity and brightness
-
Product
Sealed Beam Bulb Testing System
H710019SSL
-
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
EMI Test System
TS9975
-
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
NI Vehicle Radar Test System
-
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
Product
SMD Array Type LCR Test Fixture
16034H
-
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
SSD Test Systems
-
Enables Rapid SSD Development and Production Ramp with Flexible Test Solution In the high-growth and highly competitive SSD market, a test system that supports multiple protocols can eliminate the need for retooling and achieve faster transitions from one product version — or one product generation — to the next. Advantest SSD Test System allows manufacturers to rapidly grow their product portfolios while remaining adaptable to the many changing needs of the evolving SSD market. This tester improves users’ engineering efficiency with powerful, easy-to-use software tools and a revolutionary multi-protocol hardware architecture, enabling accelerated SSD product development and a faster time-to-manufacturing ramp.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
-
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
-
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
Semiconductor Test Software
-
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Dielectric Test Fixture
16451B
-
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
CATR Benchtop Antenna Test System
ATS800B
-
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
Memory Test System
T5221
-
The T5521 is a memory test system that supports wafer test and wafer burn-in test of non-volatile memory devices such as NAND flash, housed within a multi-wafer prober to reduce test floor footprint.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-8010A
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/HMM testing*Fast 50 Ω high voltage pulse output with typical 300 ps rise time*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω-configuration*High pulse output current up to ±80 A (short circuit) with 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 300 ps to 50 ns*1 built-in pulse width: 100 ns*Optional external pulse width extensions 5/10/50/100/200/500 ns using an external pulse width extender TLP-8012A5*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
Product
Container & Package Testing
-
*Incline Impact. *Drop. *Cobb. *Static and Dynamic Compression. *Dart Puncture. *Environmental Conditioning. *Vertical Linear, Rotary Motion, Sinusoidal and Random Vibration. *Internal Pressure. *Vacuum
-
Product
Benchtop Communication Test System
ATS3000A
-
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Liquid Test Fixture
16452A
-
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
