Semiconductor
active or passive elements connected as an electronic circuit using a crystalline subtance, eg. silicon or germanium.
See Also: iJTAG
-
Product
DC Bias Injector
J2130A
-
When using the network analyzer to measure impedance, such as the capacitance and ESR or a capacitor, or the DCR of an inductor, etc., it is often necessary to provide a voltage bias to the device being tested. This is true of semiconductor junction capacitances, varactors, and some ceramic capacitors (especially X5R). In these cases the impedance is a function of the DC bias on the device. The Picotest DC bias injector (J2130A) is used for this purpose during impedance measurements.
-
Product
High Voltage Switching Test System
-
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
Product
IC/BGA Tester
Focus-2005
-
As a screening checker to detect defective devices(mainly electrostatic destruction)which are returned from fields before failure analysis process of IC/LC in the quality assurance division of semiconductor manufacture.As a screening checker to detect defective devices before acceptance inspection by IC/LSI expensive tester at semiconductor company(trading, manufacture)Short/Open checker for semiconductor sensor device.It is possible to measure two kinds of measurements which are constant voltage biased current measurement and constant current biased voltage measurement. User can set the threshold of 10 ranks. （auto measurement）Only device can be measured. It is also possible to fabricate the test fixture.Various devices can be measured by replacing the socket board.It is no need to generate complex test programs as reference values are calculated from good device.It can be expanded by adding multiplexer boards which are 128pins per one board.(MAX 2048pins)
-
Product
2-Slot BRIC, 256x4, 1Pole, PXI Matrix (2 Sub-cards)
40-559-201-256x4
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays. With their high level of switching density, these PXI matrices allow a complete Functional ATE system to be housed in a single 3U PXI chassis and allow the use of much lower cost 8 or 14-slot chassis. The 40-559 matrices can be used in many industries; typical applications include automotive ECU and semiconductor package testing. Dual analog busing for the narrower matrix options, enable completely separate matrices within a single module for parallel testing.
-
Product
Flat Carbon Sensor Conductivity meter
HE-960LF / FS-09F-1/2
-
It is effective to keep the dilution of Slurry constant. Maintaining an appropriate conductivity value contributes to process stability in the wafer polishing process. Even highly viscous sample liquids such as CMP Slurry can be measured without problems because they use a sensor structure that reduces the risk of the sample liquid sticking to the electrodes. In addition, the sensor is made of a wetted material with excellent chemical resistance, which meets the cleanliness requirements of semiconductor processes. In addition to the above, it can also be used for introduction at the semiconductor process development stage and conductivity control of special chemicals.
-
Product
WDXRF Wafer Analyzer
2830 ZT
-
The 2830 ZT wavelength dispersive X-ray fluorescence (WDXRF) wafer analyzer offers the ultimate capability for measuring film thickness and composition. Designed specifically for the semiconductor and data storage industry, the 2830 ZT Wafer Analyzer enables the determination of layer composition, thickness, dopant levels and surface uniformity for a wide range of wafers up to 300 mm.
-
Product
Relays & Contactors
-
Panasonic Industrial Devices Sales Company of America
Relay options include Panasonic's exclusive PhotoMOS® Semiconductor Relays (otherwise known as Photo, Photo Voltaic, Solid State or MOS-FET Relays) along with Power, Signal, Automotive and High Frequency Relays.
-
Product
Thermalyze Extension for Steady State Analysis
Lock-In
-
Steady-state thermography is limited to detecting hot spots that heat up a minimum of 100 mK (0.100°C). This may be useful for locating shorts on high-power devices, but is inadequate for detecting low power defects such as semiconductor device leakage current or short circuit with very low or very high resistance. Steady-state thermography also suffers from poor spatial resolution as the heat from localized hot spots diffuses rapidly, blurring the location of the heat source.
-
Product
Custom Test Fixtures
-
For popular high speed components like semiconductor packages, and test contactors, we have developed a custom test fixture which allows the use of high bandwidth microprobes to measure virtually any I/O pin, according to GigaTest's methodology and requirements.
-
Product
Bonding Tester
PTR1102
-
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
-
Product
5.0 MP Camera For Rockchip RK3399
E-CAM50_CU96
-
e-CAM50_CU96 is a 5MP Fixed focus MIPI camera for 96Boards compliant Rock960 developer kit featuring Rockchip RK3399 processor. This 4-lane MIPI Camera for Rock960 board is based on our popular low-light camera module, e-CAM55_CUMI0521_MOD which has 1/2.5" AR0521 CMOS Image sensor from ON Semiconductor® and a built-in Image Signal Processor (ISP). It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Product
Semiconductor Device Parameter Analyzer/Semiconductor Characterization System Mainframe
B1500A
Analyzer
Current-voltage (IV) measurement capabilities of spot, sweep, sampling and pulse measurement in the range of 0.1 fA - 1 A / 0.5 V - 200 VAC capacitance measurement in multi frequency from 1 kHz to 5 MHz and Quasi-Static Capacitance-Voltage (QS-CV) measurement capabilitiesAdvanced pulsed IV and ultra-fast IV measurement capability from minimum 5 ns sampling interval (200 MSa/s)Up to 40 V high voltage pulse forcing for non-volatile memory evaluation
-
Product
Micromanipulator
XYZ 300 Series
-
Quarter Research and Development
The XYZ 300 Micropositioners provides 3-axis motion with .300" movement on each axis. Motion is controlled by three adjustment screw knobs that provide .025" resolution per turn. A general purpose micro positioner, it is intended for industrial, medical, biological, semiconductor, and general scientific applications.
-
Product
Probe Card
-
Japan Electronic Materials Corp.
The probe card is a tool for testing semiconductors used at "Wafer Test" to check quality of IC or LSI in the first process of semiconductor manufacturing. The probe card is expendable.
-
Product
WATOM
-
Wafer edge and notch profile measurementThe use of smaller and smaller patterns in the semiconductor industry calls for increasingly advanced materials of extremely high quality. In response to the steady improvements in the quality of wafers, KoCoS Automation has developed WATOM, a wafer edge and notch profile measurement tool which heralds a new era of extremely precise wafer geometry measurement.WATOM supports quality assurance throughout the wafer manufacturing process, starting at the very beginning and continuing on through to wafer reclaim.The WATOM Edge and Notch Wafer Geometry Analyser sets the worldwide benchmark for the quality assurance of geometrical measurements in semiconductor wafer manufacturing, combining the highest quality standards with top-class service. These high-precision, laser-based edge profile measurement tools are specially designed for optimum integration in manufacturing lines within the semiconductor industry.
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
ST/MT Family
-
MT System is a configurable test equipment suitable to verify static and dynamic parameters of power semiconductors (i.e. IGBT, MOSFET, DIODE, THYRISTOR, SiC, GaN, etc) packaged and unpackaged (discrete, module and substrate). ST System is a test equipment suitable to verify stability or drift of all static parameters of discrete power semiconductors.
-
Product
Ultrasonic Transducers
-
Sonix S-series ultrasonic NDT transducers are designed in-house to meet the demanding nondestructive testing requirements of semiconductor manufacturing. We offer the collaborative expertise to help customers choose the best ultrasonic NDT transducer for their application, based on three primary considerations.
-
Product
Enabling Low Power, High Reliability, And High Performance Design
Lattice Nexus Platform
-
The Lattice Nexus FPGA platform combines Lattice’s long-standing low power FPGA expertise with leading 28nm FD-SOI semiconductor manufacturing technology. With this platform, Lattice enables the rapid development of multiple device families that deliver low power, high performance, high reliability and small form factor.
-
Product
Semiconductor Yield Management Software
QuickLoad-Central
-
QuickLoad-Central is our new STDF filtering, analysis, reporting, managing, viewing and editing tool. It looks at all your STDF files before you need to, pulling out key information to pre-generate reports and help you quickly find the files you need. You can list files of interest with yield and header information on our dashboard, visualize your data, open pre-generated reports or push any information from them that you can think of to JMP, Excel or other analysis tools.
-
Product
Stand-alone Ozone Delivery System For Advanced Processes
SEMOZON® AX8585
-
SEMOZON® AX8585 stand-alone ozone gas delivery system is designed around the AX8410 PRIME ozone generator to provide high flow, high concentration, ultra clean ozone generation and delivery. This fully configurable product line is designed to meet the ever changing needs of the semiconductor industry. Each SEMOZON AX8585 is a fully integrated, high output ozone gas delivery system intended for use in an increasing number of semiconductor process applications such as ALD, CVD, TEOS/Ozone CVD, photoresist strip, wafer cleaning, contaminant removal, and oxide growth.
-
Product
Low-leakage Switch Matrix Family
-
Conducting all the parametric measurements necessary for the numerous test structures on a semiconductor wafer can be a time-consuming and expensive process. With the cost of end-user devices continuing to drop, even laboratory characterization environments must reduce the cost of test. Until now engineers and scientists working on current and future semiconductor process technologies were faced with a difficult choice: either use a semiconductor parameter analyzer with positioners on a wafer prober, which limits the ability to perform automated test, or use a switching matrix and probe card, which reduced the analyzer's measurement resolution. Utilizing a switching matrix with a semi-automatic or fully-automatic wafer prober enables characterization tests to be automated, eliminating the need to have an operator manually reposition the probes each time a new module needs to be tested. This reduces both test time and cost. Due to the many price/performance points available, Keysight's switching matrix solutions provide the flexibility to choose exactly what your testing needs require, without overspending.
-
Product
Configurable OSAT Friendly Pick-and-Place Handler
Delta Eclipse
-
Eclipse delivers scalable performance for testing a wide range of semiconductors, from analog ICs to high-performance CPUs and mobile processors. The Eclipse is a high-speed pick-and-place handler designed to test up to 16 Integrated Circuits (ICs) in parallel, at temperatures from -45°C to +155°C*, with throughput up to 13,000 UPH.
-
Product
4K Multi-Camera System (TRICAM)
E-CAM130_TRICUTX2
-
e-CAM130_TRICUTX2 (TRICamera) is a multiple camera solution for NVIDIA® Jetson TX2 developer kit that consists of three 13 MP 4-Lane MIPI CSI-2 camera board and an base board to interface with the J22 connector on the Jetson TX2. Each camera is based on the camera module e-CAM137_CUMI1335_MOD, 1/3.2" AR1335 color CMOS image sensor from ON Semiconductor® and integrated high performance Image Signal Processor (ISP).
-
Product
Optical Metrology
YieldStar
-
Our YieldStar optical metrology solutions for the semiconductor industry can quickly and accurately measure the quality of patterns on a wafer.
-
Product
WAFERMAP
-
WAFERMAP is an award winning software package used to collect, edit, analyze and visualize measured physical parameters on semiconductor wafers. WAFERMAP can import data files from various metrology tools such as ellipsometers, thickness gauges and four point probes. The imported data can then be visualized or printed as line scans, contour plots, 2D or 3D plots or as a histogram.
-
Product
Semiconductors Testing
test
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
Product
High-Density Precision SMU (10 PA, 30 V)
PZ2131A
Source Measure Unit
The Keysight PZ2131A is a high-channel density precision source / measure unit (SMU) having 5 channels per module and saving space for a wide range of applications requiring numerous precision power supplies. The narrow-pulse function and fast Digitizer Mode allow the PZ2131A to expand the conventional static DC measurements to emerging dynamic measurements. Its seamless current measurement ranging function eliminates the time it takes to change the range and expands the dynamic range to cover multiple measurement ranges, which reduces test duration. These capabilities make the PZ2131A suitable for applications that require numerous precision power supplies, such as semiconductor reliability tests and integrated circuit (IC) tests. The Keysight PX0107A low noise filter adapter lowers its voltage source noise level, which makes the PZ2131A suitable for noise-sensitive applications such as quantum computing as well.
-
Product
Moisture Analyzer
5800
-
The 5800 is ideal for high-purity gas production, semiconductor gases, and the production, storage and transmission of olefins. It is suitable for use in industries including hydrocarbon processing, industrial gas and semiconductors.
-
Product
Mixed Signal Test Systems
MTS1020i
-
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
