-
product
Manufacturing Test Modules
Manufacturing Test Module (MTM) Series instrumentation from Acroname is the platform you need to free your production testers from the burdens of validation test equipment. Mix and match modules to create a complete tester within a fixture frame, eliminating benchtop and rack equipment - all without sacrificing the robustness and reusability you demand from your equipment.
-
product
PXI Expandable 16x16 RF Matrix 75Ohm 1.0/2.3
45-720A-741
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-751
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
CAM/TRAC Test Kits
The Camtrac (registered trademark) series test fixtures provides ‘Z’ axis motion that reduces probe side loading typically seen with Clamshell type test fixtures. This not only extend the life of the probes, but additionally, provide better probing accuracy, especially on fine pitch test centers. Camtrac fixtures are available with the most widely used interfaces in the test industry.
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
product
Accessories
Hunan Linkjoin Technology Co., Ltd.
Linkjoin accessories - electromagnet, core test fixture, epstein frame, DC permeameter, AC permeameter, reference magnet, magnetic flux fixture, solenoid, helmholtz coil, temperature controller, etc
-
product
Accessories For Instruments And Fixtures
N1254A
The N1254A includes several optional accessories and adapters for instruments.
-
product
RF Chamber Fixtures
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
-
product
Manual Fixture Kit
230355 – CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Universal Tensile Testing Machines
Dongguan Amade Instruments Technology Co., Ltd
Universal tensile testing machines are testing equipment that are used to conduct mechanical testings of static load, tensile, compression, bending, shearing, tearing, stripping, applied to plastic sheets, pipes, tapes, rubbers, electric wires, springs, sponges, fibers etc. Tensile test is performed to measure and analyze the physical performances of different types of materials and finial products, playing an important role in developing new materials and controlling products quality. From the perspective of function, universal tensile testing(UTM) machine is an omnipotent instrument Just as the name implies. Clamps or fixtures are interchangeable on the basis of different test pieces, enabling various testings to be carried out on one tensile testing instrument. Options of single-column stand or twin-column stand can be available based on the specimen’s tensile/compressive force and dimension. Computerized tensile tester is preferred rather than microprocessor version If users want testing results including curve graphics between time, force and displacement.
-
product
Stand-Alone Test Fixture
MA 2011/D/H
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1000Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,00 kg
-
product
Test Adapters
In our specially developed MG range of linear test adapters (test fixtures), we use solid aluminium components in our mechanical construction. This is to ensure the reliability and contact accuracy of the test adapter.
-
product
Adjustable Press Plate Bed of Nails Testers
Protector Adjustable Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
product
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA
910121178
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA.
-
product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
product
EBIRST 68-pin Male SCSI Termination Fixture
93-015-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
PC Based Test Setup for LED Driver of LED
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
product
Tooling And Fixturing
Control develops and supplies fixtures and test accessories :*For a vast field of applications - ICT (In-Circuit Test), functional test, Flash programming, EoL (End-of-Line) test systems, etc.*For all handling systems currently used in the market: online or offline, mechanical, pneumatic or vacuum operation*From simple mechanical fixtures, with a few hundred probes and low production volumes, to highly complex accessories with thousands of probes, double-sided probes, double acting, etc.
-
product
Ionization Test Set
PFK-105
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
-
product
Time Domain/Fault Location Analysis For E5061B
E5006A
The E5006A Time Domain/ Fault Location Analysis option allows you to locate the discontinuities and mismatches of devices such as cables. By employing the gating function in the time domain and transforming the data back to the frequency domain, you can remove unwanted responses of connector mismatch in your fixture. In addition, the cable SRL (Structural Return Loss) analysis capability is provided with the E5006A.
-
product
Automotive Ethernet Test Fixture
AE6941A
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
product
Test Port Cable, 1 Mm
11500L
Connect test ports to devices, fixtures, or probe tips with this 24-cm cable featuring a return loss of 16 dB minimum.
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
RF Shielded Box
LTL B12001
LTL B12001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B12001 RF shielded test enclosure can comfortably houses the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
PCI RF Switch Cards
These 8x9 RF Switch Cards are suitable for switching frequencies up to 500MHz. Available in either 50 or 75 versions with SMB coaxial connectors. These switch cards are intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic isolation switches are located on all coaxial connections, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
