-
Product
Precision LCR Meter With Component Fixture And Limits Comparator
LCR400
-
0.1% basic measurement accuracyDual 5 digit high brightness displaysAutomatic component recognitionBuilt-in 4 terminal component fixtureLimits comparator with 8 Pass bins plus 2 Fail binsThree test frequencies, switchable biasRS232 interface standardOptional SMD tweezers, BNC connectors, Kelvin Clip test lead set, and PC logging software
-
Product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
-
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
Product
10-CH Pneumatics CAN
YAV90PNE
CAN Interface
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
Product
SHC68-H1X38 High-Speed Digital Flying-Leads Cable Accessory, 1.5m
192681-1R5
Digital Cable
76-Pin, Female Flying Leads to 68-Pin, Male VHDCI, Shielded, 50 Ω Digital Cable - The SHC68-H1X38 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments directly to individual header pins for use with a custom breakout fixture. The flying-lead cable has paired signal and ground lines for each channel to preserve signal quality. Each signal and ground line is designed to plug directly into any 0.1 in. header connector. It is a shielded, 50 Ω cable.
-
Product
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA
910121178
Soldering Fixture
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Manual Test Press Fixture
750/752 Series
-
RTI's manual test presses are compact, portable, all-inclusive, and easy to use. Single lever operation and 100% vertical compression makes the manual test press an ideal solution for PCB, hybrid module, and high pin count device-level testing when complex test requirements cannot be met with a test socket and breakout board alone.
-
Product
PLTS Advanced Calibration
N19305B
-
PLTS N19305B extends the N19301B base product to perform advanced calibration techniques such as Automatic Fixture Removal (AFR)
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
-
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
Product
ICT/FCT-Fixtures (Small IF)
GenRad CK-1-228X-S
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 335 x 250 mm (wxd)
CMK-02
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 197 x 114 mm (wxd)
CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
-
Product
Tweezers Contacts Test Fixture
16334A
-
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
Product
9050TR - 50 Module, 2-Tier Solution with Platform
-
The rack mountable 9050TR receiver is designed to accept 9025 and 9050 ITAs and is essential to support advanced mass interconnect requirements. This 50-module solution can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can also be intermixed to establish custom interfaces which are ideal for functional and system testing applications.
-
Product
Test Probes / Test Fixtures
-
INGUN has an unbeatable assortment of test probes and test fixtures for individual testing tasks.Thanks to many years of experience in the testing equipment field, INGUN offers the suitable test solution for every test requirement.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
CMP Mechanical Kits
CMP-XXX-HP
-
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
Product
Manual Fixture Kit
230371 – CMCSK-02-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Custom Motor Test Systems
-
Magtrol's Customized Motor Test Systems (CMTS) are PC-based, turnkey systems custom designed and built to meet your specific motor testing requirements. By integrating Magtrol's motor test equipment with power supplies, adaptable fixtures, custom tables/cabinets, printers, etc., Magtrol's engineering team can customize PC-based, turnkey systems and modular test benches for almost any motor test application.
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
Product
Radar Altimieter Test Panel for ALT-50/55
TA-55
-
Radar altimeter panel designed after the ALT-50A test fixture. (Ref. Fig. 5-1). Panel allows testing of the indicator or R/T independently or together. An internal power supply is provided to support stand alone testing of the indicator. This panel contains a 4 digit DVM and comes with enclosure. This panel will allow by the book testing.
-
Product
Custom Designed Test Fixtures
-
We specialize in automated test systems for both RF and digital devices, modules and systems. Please call to discuss your test requirements.
-
Product
Serial Distance Display
TA903-03
-
This panel mounted or portable display will read Bendix/King serial distance as generated by their DME systems or GPS products. This long standing three wire format of CLK, DATA and REQ can now easily be displayed without the expense of a KTS143 test fixture. This product is ideal for shop and aircraft troubleshooting. The extruded aluminum enclosure is a standard DIN size(1/8) and the unit interfaces through a 25 pin D connector.
-
-
Product
2m BNC Test Cable
16048D
Test Port Cable
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
Device Parameter Analysis
-
bsw TestSystems & Consulting AG
The complexity of DC Parametric Characterisations has significantly increased with the level of miniaturisation in the semiconductor industry. The demand is not only on the precision of the measurements. New measurement methods have emerged to gain insight into phenomena previously unknown or only of marginal relevance. One example is "Pulsed IV" which is now widely in use. The modular concept of the Keysight B1500A allows users to tailor their instrument exactly to their needs. Flexible upgrades ensure the investment for many years. Together with bsw AG you will get an optimum solution for your application. Our experts provide not only support for the instrument itself but have also working knowledge of all the solutions surrounding it. This includes Cabeling and Adapters, Fixturing for packaged Parts and of course Wafer Probing. We help customers from replacements of broken or worn-out parts to planning and deployment of turn-key-systems.
-
