Showing results: 1 - 15 of 17 items found.
-
SCHILLER AUTOMATION GmbH & Co. KG
With ever-growing performance, accuracy, and precision required by 112G/800G PAM4 solutions, Wilder has designed a robust HCB and MCB fixtures to support OSFP-XD, QSFP-DD, OSFP and SFP-DD compliance testing. In addition, CMIS_GUI Software provides: Displays of many of the settings and Controls in the Module including Lane States, Module Power States and Optical Power. Alarms and Warnings for Module Temp and Vcc and Optical Power Controls for Module Power, Margins, and read access to Descriptors and Data Path Configuration. Direct Read/Write access to the I2C and CMIS Memory Map as well Scripts that directly access the CMIS Memory Map Registers.
-
SCHILLER AUTOMATION GmbH & Co. KG
HDMI test adapters and test fixture kits facilitate Source and Sink compliance testing and HDMI cable testing. Our products are used in Certification Testing to CEA 1.3b, 1.4a, 2.0 and 2.1 standards. 1080p and 4K formats are supported. We offer A and D style plug and receptacle connectors, male and female SMA leads, with and without HEAC channels.
-
SCHILLER AUTOMATION GmbH & Co. KG
USB-IF approved USB4™ Compliance test fixture. Wilder’s robust next-gen USB4 Microcontroller solution provides USB Type-C® host compatibility. The USB4 Microcontroller along with USB-C® TPAs can be used for testing USB-Type-C hosts and devices.
-
-
SCHILLER AUTOMATION GmbH & Co. KG
Our latest PCIe G5 M.2 Socket3 CLB and CBB enables pre-Compliance testing while maintaining compatibility with PCIe CEM Set via use of MMPX connectors.
-
SCHILLER AUTOMATION GmbH & Co. KG
The Gen4 Mini-SAS HD adapter kit will facilitate compliance testing for SAS-4 host, device, and cable. The left and right-hand version plug adapters are designed to test side-by-side.
-
SCHILLER AUTOMATION GmbH & Co. KG
The Standard SD Express Memory Card Test Adapters support PCIe® 16 GT/s (Gen4) and PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD8.0 and SD7.1. Minimal crosstalk, short trace lengths. The Micro SD Express Memory Card Test Adapters supports PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD7.1. Minimal crosstalk, short trace lengths. They all support SDHC, SDXC, and SDUC operation modes Data collection via Lab Standard SSMP Test Cables and hard gold mating surface allow for high cycle count insertions and reliable performance.
-
SFF 8639 Gen4 (U.2) -
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
SCHILLER AUTOMATION GmbH & Co. KG
Wilder Technologies Enhanced DisplayPort™ and miniDisplayPort™ test adapters enable Host and Device testing to DP2.1 Specifications. Supporting increasing data rates (UHBR10, UHBR13.5 and UHBR20) to drive 8k displays and higher refresh rates, Wilder’s fixtures provides the a platform for pre-compliance and compliance testing.
-
SCHILLER AUTOMATION GmbH & Co. KG
The CFX supports CFexpress Spec (Ver 1.0), PCIe Gen4. The CFX Plug test adapter allows easy access via SMA connections, to measure or inject data signals. The user can also access +3.3V, its respective GND, Reset and other control lines via a low-speed 6-position connector.
-
SCHILLER AUTOMATION GmbH & Co. KG
The USB 3.1 USB (10 GT/s) Type-C Electrical Test Fixture Set provides a worst case, ISI hardware channel for PHY’s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals.
-
M.2 Gen5 Socket3 CLB and CBB -
SCHILLER AUTOMATION GmbH & Co. KG
Our latest PCIe G5 M.2 Socket 3 CLB and CBB enables pre-Compliance testing while maintaining compatibility with PCIe CEM set via use of MMPX connectors. It includes CMTS as well as adapter cables.
-
M.2 Gen4 Socket3 -
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 3 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 3 Source and Sink devices.
-
M.2 Gen4 Socket2 -
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 2 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 2 Source and Sink devices.
-
SCHILLER AUTOMATION GmbH & Co. KG
Automotive Product fixtures supports the 100/1000/MultiGBASE-T1 Compliancy standards with many different connectors such as MateNet (TE), H-MTD (Rosenberger), Mini50 (Molex). Also, we provide generic solder down board to enable engineers ability to connect their connector of choice.
