Gigabit Ethernet Test
-
Product
DWV/IR Test Systems
-
When used in conjunction with ART's own parametric relay test systems such as the RT290, the RT900 offers high speed AC and DC Hipot (dielectric withstand voltage) and Leakage testing of relays or other multi-pin passive devices.
-
Product
Ethernet Switches
-
The switches CXR Carrier Ethernet CE 2.0 allow easy and economical transition to 10 Gigabit Ethernet class operator while providing hardened features in temperature and electromagnetic immunity.
-
Product
Electronic Testing Services
-
Printed Circuit Board Testing and Repair Services CM Wings Board Testing Inc. was founded in 1983. Its founding was a direct response to theneed for a truly customer service oriented facility for printed circuit board test and repair.
-
Product
Information Technology Testing
-
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing information technology products according to applicable standards. We help you not only verify the classification of your product, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Test House Services
-
At TS-Space Systems we have over 30 years experience in designing, building and operating vacuum systems for space simulation and materials testing. We have three in-house thermal vacuum chambers which are configurable for a range of temperatures for either monitored vacuum bakeout or thermal vacuum cycling. We design, build and operate these systems in-house which means we are more flexible than most test houses and are happy to modify feedthroughs, manufacture additional support equipment and even change the operation of the chambers, where possible, in order to accomodate customer requirements.
-
-
Product
Dielectric Strength Test Apparatus
CX-KD12
-
Shenzhen Chuangxin Instruments Co., Ltd.
To improve the insulation board and creepage dielectric properties, surface brushed polished, bottom bracket the minimum distance from the edge of >35mm, the altitude of 2000 meters designed to meet the strength test requirements of 12KV
-
Product
Wafer Testing
Trio Vertical
-
SV TCL's TrioTM is a reliable solution for advanced wafer testing challenges, specifically full array and parallel probing. We offer a complete line of vertical probe card products, each designed for your unique application.
-
Product
Pressure testing solutions
-
Pressure testing involves applying stored energy to an assembly of parts, in order to verify its strength, its integrity and/or its functionality. Pressure Testing generally uses the application of a test fluid (liquid or gas) into a volume and the fluid is then pressurised to exert pressure forces onto the test object that can be measured.
-
Product
Vibration Testing
-
DATASYST Engineering & Testing Services, Inc.
Small, medium and large electro-dynamic vibration systemsServo-hydraulic vibration systemsCombined environment system (Temp-RH/Vibration)
-
Product
In-System Test Programming System
WriteNow
-
Based on proprietary WriteNow! Technology, the WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices from various manufacturers and have a compact size for easy ATE/fixture integration. They work standalone or connected to a host PC, and are provided with easy-to-use software utilities.
-
Product
Battery & Electrical System Testing
12-0200
-
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
Product
Partial Discharge Testing Equipment
AR700
-
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
-
Product
AeroEngine Test Cells
-
A tec is a leading provider of jet engine test cells and flight component support. We provide our customers with high quality, superior value maintenance facilities and equipment for the testing of all types of turbine engines. We excel in both the design and construction of new facilities and the technological refreshment and sustainment of legacy systems. The Atec companies operate worldwide with new test cells, test cell modifications, engine test adapters, ADAQ™ control systems, support equipment, test benches, utilities subsystems, site surveys, repairs and training, and Master Service Agreements (MSAs).
-
Product
3U CompactPCI Serial 3-slot SSL w/o RTM w/ Ethernet
1CPCIS-303-L200
-
3U CompactPCI Serial Backplane with 3 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 2x CompactPCI S.0 peripheral slots, without connectors for RTMs (RearTransition Modules), Ethernet routed as full mesh.
-
Product
DNS leak test
-
Sometimes a VPN can fail to protect your device’s DNS queries even when the rest of your traffic is concealed by the VPN tunnel. This is called a “DNS leak.” If your DNS leaks, unauthorized entities, like your internet service provider or DNS server operator, can see which websites you visit and any apps you use.
-
Product
API Security Testing
-
Nowadays, APIs are frequently used for communication between two applications. In this communication, lots of sensitive data is transferred between devices and the server.In order to be protected in the event of a data loss or attack, we must secure our API.
-
-
Product
System Test
-
Testing a complete system is very different from unit and integration test. It starts with the V model that defines the system requirements, and this needs an effective system test capability that includes both the system and the environment around it. If the system has interfaces to the outside world, communications links or human control, these interfaces have to be tested.
-
Product
INTERFACE TEST FIXTURE KITS
GENRAD 2270
-
Test-X GR Series CAM/TRAC® kits offer the same "Z" axis motion as the standard CT Series with the advantage of interface compatibility.Standard features include locking handle assembly, 3/8" FR4 probe plate, and 12 position I/O block interface..
-
Product
Partial Discharge Test Set
-
We are an unparalleled name in the industry, engaged in manufacturing and exporting Partial Discharge Test Set that is broadly used for instrument transformers to test the discharge of voltage. This test set is manufactured in compliance with set international quality standards using optimum quality components under the observations of our experienced professionals. Further, it is made available in several specifications to meet the exact requirements of the clients. Our offered Partial Discharge Test Set can be owned from us at nominal prices.
-
Product
Microindentation Hardness Testing Systems
LM Series
-
Perfect for a production facility or a research lab, LECO's LM Series Microindentation Hardness Testing Systems offer a variety of models (including analog and digital) with the advanced features that meet your requirements and budget.
-
Product
NTSC Test Signal Generators
-
Provides an economical means for generating the most common SD analog composite video reference timing signals required to operate various SD analog composite video switchers, effects generators, VTRs/VCRs, cameras, video edit controllers, and other professional video equipment.
-
Product
Salt Spray Test Chambers
-
Labodam salt spray test chambers are reliable instruments for testing the corrosion resistivity of products with painted, organic, or inorganic film surface.
-
Product
Complete Testing Solutions
-
System includes a lamp and monochromator for a tunable light source, which is coupled to a high sensitivity source meter with measurement software. This user-friendly system is the most powerful Spectral Response system currently on the market, but its true power is the ease of upgrading from the base PTS-1 to the more powerful PTS-2-QE (Quantum Efficiency) or PTS-3-CPM (Constant Photocurrent Method). Designed for researchers who have limited budgets but want to start work immediately, this allows the ability to do baseline studies until additional funding for the full QE or CPM system becomes available.
-
Product
Compressed Air Testing
-
Parker's compressed air testing units provide a cost-effective means of quickly evaluating compressed air for the presence of microbes. The units are lightweight, ergonomically designed for ease of use, and supported by Parker's global sales and service network.
-
Product
Ethernet Speed Test Solution
NET-BOX™
-
The NET- BOX is an optimized Quality of Experience (QoE) testing platform that offers a low cost, reliable, high performance FPGA-based alternative to expensive high-end laptops often used for enterprise and speed tests. With a multi-test port architecture, with four 1GE, one 2.5GE test and 4 Gbps full line rate capability, the NET-BOX can truly test the limits to verify Quality of Service (QoS) and assure QoE for the ever growing high-speed internet service at and beyond 1 Gbps.
-
Product
Glow Wire Test Apparatus
GWT A2
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
