Sources
The origin.
-
Product
CAN Sensoy/ Interface
Strain
-
Reach Technologies' CAN Strain Sensor Interface sources, conditions and digitizes 8 strain sensor inputs for collection via CAN. The module is ideal for conveniently adding strain data to a distributed CAN network. The CAN Strain Sensor Interface is configurable via a CANopen stack.
-
Product
Automatic Sampling Robotic Diffusion Station
Phoenix RDS
-
The Phoenix RDS (Robotic Diffusion Station) platform provides fully automated sampling and collection for either six or twelve vertical diffusion cells in a compact footprint, using the same heating and stirring blocks as are found in the DB-6. A third block holds a wash station and up to five additional media sources. Samples are collected into 12×32 vials with pre-slit septa. Controlled by Teledyne LABS Diffusion Master™ software, up to two RDS systems (24 vertical diffusion cells at once) can be operated independently from a single computer workstation.
-
Product
Seismic interpretation Software
GeoTomCG
-
GeoTomCG can process crosshole or VSP seismic or radar data. The display shows calculated radar velocities. High velocity zone at depth of 27 m is caused by an abandoned mine. Other zones of contrasting velocities are geological features. S and R indicate source and receiver positions, respectively.
-
Product
50Hz-100kHz LCR Meter
11022/11025
-
Chroma Systems Solutions, Inc.
0.1% basic accuracyTransformer test parameters (11025), Turns Ratio, DCR, Mutual Inductance0Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz test frequencies21ms measurement time (≥100Hz)Agilent 4263B LCR Meter commands compatible4 different output resistance modes selectable for non-linear inductor and capacitor measuringHigh resolution in low impedance(0.01mΩ) and high accuracy 0.3% till 100mΩ rangeAdjustable DC bias current up to 200mA (constant 25Ω) (11025)1320 Bias Current Source directly control capability0.01mΩ ~ 99.99MΩ wide measurement range (4 1/2 digits)Dual frequency function (11022 option) for automatic productionBIAS comparator functionComparator function and 8/99 bin-sorting functionPass/fail judge result for automatic productionHandler interface trigger edge (rising/falling) programmableTest signal level monitor functionStandard RS-232, GPIB, and Handler I/FOpen/short zeroing, load correctionLabView® Driver
-
Product
Open Source Software
-
Automate OSS selection and approval, identify applicable risks in OSS libraries and container images, reduce SCA noise by 80%, and implement accurate SBOMs.
-
Product
Optical Spectrum Analyzer - PXI
OSA 1000 Series
Spectrum Analyzer
The OSA 1000 Series provides grating-based spectral test and measurement. It is an excellent fit for the testing of optical sources, amplifiers, transceivers and passive optical components.The OSA is available in a range of wavelengths for different applications, so you pay only for the capabilities you need.
-
Product
Widely Tunable Ultrafast Laser System For Multiphoton Imaging
InSight X3
-
Spectra-Physics’ new InSight® X3™ is the third generation of Spectra-Physics’ industry leading InSight platform, specifically designed for advanced multiphoton microscopy applications. Based on patented technology1, InSight X3 features a broad 680 nm to 1300 nm continuous, gap free tuning from a single source, nearly double the tuning range of legacy Ti:Sapphire ultrafast lasers. InSight X3 delivers high average and peak power levels across the tuning range, including critical near infrared wavelengths above 900 nm for deepest penetration in-vivo. With Spectra-Physics’ integrated patented DeepSee™, the industry standard dispersion pre-compensator, the short pulses are optimally delivered through a microscope to the sample for maximum fluorescence and penetration depth. InSight X3 also has exceptional beam pointing stability, beam quality and output power stability, as well as fast wavelength tuning, making it ideal for microscopy.
-
Product
SGMA RF Source
SGS100A
-
The R&S®SGS100A is an RF source designed to meet the requirements of automated test systems. It is available as a CW source or as a vector signal generator with an integrated I/Q modulator. With its frequency range of up to 12.75 GHz, the vector signal generation version covers the essential digital signals. The CW version can be used as a flexible local oscillator and for interference testing against mobile radio standards.
-
Product
Compact Monitoring Probe
ISDB-T/Tb
-
Network operators:automate the tests of new transmittertemporary monitoring/investigation toolrebroadcasting receiver: RF to ASI or IPBroadcasters: off-air monitoring probe to validate the on-air contentTV/STB producers: automated tests against a professional receiverLabs: easy & simple access to live DTV sources via RF
-
Product
Limiters
-
A limiter catches the loudest peaks of an audio source and applies brick wall compression that prevents it from exceeding the clipping point of 0 dBFS.
-
Product
Reflection Meter
RC-088
-
This instrument is a special equipment for measuring the reflectivity of rearview mirror (or similar product) of motor vehicle. The product composes intelligent measuring instruments, optical integrating sphere, parallel lamp, standard light source, constant current source etc. It is easy to operate，it can measure the reflectivity quickly and accurately. On instrument structure, it adopts standardized modulation design. It takes latest single chip as its digital central processing element. After the measuring signal is converted by modulus, CPU will do some computation and compensation. The instrument can display the reflectivity of device which is measured in rear time. It operates simply and quickly, the indication is direct and accurate. It’s good for quality examination &control in the production scene as well as laboratories. This product has the convenience &quick demarcation way, can meet requirement of different occasion. It is applicable for measuring light reflection on mirror and not mirror parts.
-
Product
High Voltage Personal Tester
HV/PT2
-
HV/PT2 is a compact, affordable, high quality proximity HV tester that is manufactured in South Africa. Your own personal HV tester is now available for you to wear at all times. A five position sensitivity switch enables the user to approach the HV source on the highest sensitivity at a safe distance.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
AC Power Sources
-
AMETEK Programmable Power, Inc.
AMETEK Programmable Power's AC power sources range from 800VA to 480kVA. From compliance test systems to rack-mounted industrial power subsystems, AMETEK Programmable Power is the leader in the design and manufacture of precision, programmable AC power sources used in R&D, test and measurement, avionics testing, inverter testing, arbitrary waveform generation, bulk power and power conditioning applications across a wide variety of industrial segments.
-
Product
USB 4-Channel Frame Grabber
2255
-
Simultaneous capture from 4 NTSC/PAL video sources High aggregate capture rate: up to 120/100 fps (NTSC/PAL) Output formats: RGB/YCrCb, packed/planar Output resolutions: full/half/quarter frame Advanced deinterlacing eliminates motion artifacts Optional hardware JPEG compression available (please call for pricing) Hardware timestamps (1ms resolution) USB powered
-
Product
Line Input Test
-
Measure the dB level and frequency of the iAudioInterface2 line input or line output (also works with any dock input audio source).
-
Product
Frequency Multipliers (WR and D Series)
-
VDI offers a broad range of millimeter-wave varistor mode, passive frequency multipliers based on planar GaAs Schottky diode technology. Frequency doublers and triplers are used to extend the frequency coverage of microwave and millimeter-wave sources.
-
Product
Register
Trend Viewer
-
A trend is a diagram facilitating analysis of long records of measured sensor values (for hours, days, months, years). Based on the sampling frequency, an n number of counts per second are performed, and their yearly number equals to 31,556,926*n. If the user needs to evaluate short-term moments of the source signal, then there is no difficulty. It is much more difficult, when it is necessary to evaluate the parameters for the entire year or several years, and no monitor and no person would handle it. And this is the case when trend building could help.
-
Product
Receiver Protectors
-
Teledyne Lincoln Microwave has a proud heritage of designing and manufacturing world class Receiver Protector / Limiter products. Our devices are used across the globe, in the air, on the ground to shield mission critical systems from damage by synchronous and asynchronous sources of RF Power.
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
Microphone Calibrators
Trig-Tek™ 402H & 402PSI
-
Portable, self-contained, high-intensity acoustic microphone calibration source
-
Product
Power Couplers
-
Communications & Power Industries
CPI BMD has extensive experience working with the world’s best accelerator scientists and engineers to fabricate power couplers for superconducting accelerators. - Used in superconducting accelerators- Found in free electron lasers- Found in Spallation neutron sources- Used in energy recovery LINACs- Used in Third harmonic cavities
-
Product
STATILLER
-
Shishido Electrostatic's DC high voltage power supplies are ideal for experiments related to static electricity and as power sources for electrostatic application devices. In addition to standard products, we also design and manufacture products based on special specifications to suit the intended use.
-
Product
Thyratrons, Ignitrons & Spark Gaps
-
High power switches such as ignitrons, thyratrons, and spark gaps require unique high power triggering systems. Our triggers can all operate from 5 mA/5 V sources and/or fiber optic inputs.
-
Product
Serial Parallel Interface
Model 2313
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
Product
AC and DC Power Sources
CFS100 Series
-
The CFS100 Series programmable AC or DC output power sources are cost effective source of power for development, test and production applications requiring anywhere from 800VA or less to 4000VA of single phase AC or DC output.
-
Product
PCI Relay Driver Card, 64-Channel
50-411A-001
Relay Driver
The card provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one terminal of a relay coil and the other terminal to an output of the 50-411A. Each output is capable of sinking up to 1A of continuous current.
-
Product
C/C++ Source Code Analysis
CODECHECK
-
CodeCheck is a programmable tool for checking all C and C++ source code on a file or project basis. CodeCheck is input compatible with all variants of Standard K&R C, Standard ANSI-C/C++, and all C and C++ compiler vendors. We support GCC-GNU Open Source C/C++ compilers. CodeCheck is designed to solve all of your Portability, Maintainability, Complexity, Reusability, Quality Assurance, Style Analysis, Library/Class Management, Code Review, Software Metric, Standards Adherence, and C++ Corporate Compliance Problems.
-
Product
Doppler Generator
Series 5000
-
Eastern OptX introduces moving target generators covering radar frequencies from 1 – 18 GHz. These compact systems provide target generation with speeds from 0 to 3000 MPH, and allows the user to set target and radar source speeds and directions. Systems may be operated remotely using wireless control with scenario generator features including flight path replication, moving source and targets, and multiple target options.
-
Product
2-Channel DAQ Module
FMC150
-
Sundance Multiprocessor Technology Ltd.
The FMC150 is a dual channel ADC and dual channel DAC FMC daughter card. The card provides two 14-bit A/D channels and two 16-bit D/A channels which can be clocked by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition there is one trigger input for customized sampling control. The FMC150 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
