Control Systems
-
product
High-performance PXI System
M5000 Series
The M5000 Series forms the backbone for the Keysight Quantum Control System (QCS) – complete digital solution that eliminates the need to design custom control solutions. Analog LOs and mixers in traditional hardware used for quantum control require frequent calibration, introduce leakage noise, and contribute to slow drifts in the performance of the system. The Keysight M5000 Series fully eliminates the need for these components leading to enhanced ease-of-use, unrivaled noise performance, and improved long-term stability.
-
product
Checking the Geometry and the Placement of the Weld
Based on the real geometric three-dimensional profile of the weld (groove) on the outside of a large diameter pipe, determine the offset of the center of the weld (groove) from the weld line. Provide continuous output of results through the RS-232 interface to the welding process control system. Provide a graphical picture of the current profile, the values of the specified and calculated geometric parameters to the operator.
-
product
IOLITE
IOLITE - Data Acquisition and Real-time Control SystemData acquisition and real-time control front-end system with dual EtherCAT buses for industrial testing applications. All-in-one solution for real-time control and feedback monitoring.
-
product
PXI Resistor Module 4-Channel 1R to 255R
40-293-013
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm - SPST
50-294-114
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Erichsen Metal Sheet Testing Machine for FLC, FLD
GBW-600
Jinan Testing Equipment IE Corporation
GBW series Erichsen Metal Sheet Testing Machine is designed on the basis of screw universal material testing machine, using the servo motor for highly accurate loading for punching, meanwhile, it is equipped with hydraulic servo control system for pre-tightening/clamping of metal sheet. It is ideal to evaluate the plastic deformation performance and ductility of metal sheet & strip materials. The cupping test for metal sheet thickness range is 0.1mm-5mm, Max. Punching capacity is 600KN, and the pre-tightening/clamping device is with hydraulic servo loading pump for 600kN capacity;
-
product
ADC DAC Module
ZET 210
ZET 210 ADC DAC module is used for constant and alternating voltage signals digital processing and parameters control (the signals are retrieved from various primary transducers). Digital and analog outputs can be used within the scope of actuating units control systems.
-
product
Control Unit
Epec 4602
Epec 4602 Control Unit has a wide range of programmable I/Os for different implementations. Epec 4602 can control 10 hydraulic blocks simultaneously by using 20 PWM outputs and 10 feedbacks. It can be used as a stand-alone controller or as part of decentralized control system.
-
product
Advanced Monitoring and Control System
SEL-734B
Schweitzer Engineering Laboratories, Inc.
The SEL-734B with low-energy analog (LEA) inputs provides advanced monitoring and control capabilities for applications, such as capacitor bank control and feeder monitoring. LEA sensor compatibility allows safe, fast, and inexpensive installations. Advanced communications report data to SCADA systems and allow remote operations from a control center.
-
product
Railway and Traffic Engineering Solutions
In the past, LXinstruments has already implemented a number of application-specific system solutions which cater for these special requirements. These solutions are often used to replace systems which have been in production for many decades. Our systems are not only employed for testing signal box technology modules, but also for testing train control system which are installed in the track bed. Due to the strong magnetic fields which occur at the DUT in combination with high voltages, the test systems require specific technical safeguards.
-
product
PXI Strain Gauge Simulator Module 2-Channel, 3k
40-265-102
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
IP Enabled Digital AV Room Control System
VSA-51
The VSA-51 is a family of devices offering the most advanced, customizable, easy to use, and affordable room control solution ever. It offers greater switching capacity of analog and digital video/audio sources. Designed around the VSA-51-R receiver, all source inputs and user controls are modular and connect to it via simple Cat5 cables. Furthermore, all wall-plates are powered from the receiver for maximum flexibility and simplicity of installation.
-
product
R37F-37M-1, 37-pin Female to Male Ribbon I/O Cable, 1m
779195-01
37-Pin Male IDC to 37-Pin Female D-SUB, I/O Ribbon Cable - The R37-37 is an unshielded ribbon cable for use with PC-based PC-based measurement and control systems featuring CompactDAQ Chassis.
-
product
DynoLAB Test Cell Supervisory System
SAKOR Technologies’ DynoLAB™ data acquisition and control systems offer reliable, cost effective automation of all types of dynamometer test systems. As with all SAKOR products, the DynoLAB system undergoes a continuous program of upgrade and improvement, regularly expanding and enhancing DynoLAB’s capabilities.
-
product
Demand Control
You can start saving money today with maximum demand control systems by Measurlogic. Our sophisticated demand control systems help property owners shed excess energy expenditures with lighting, air conditioners, ice machines, and more. We can help you build a plan for maximum energy savings.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm With SPDT
50-293-111
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Compact PCI AE Chassis
MICRO-II
The Micro-II is an industrial chassis built to enable powerful AE testing capabilities in a compact form factor. Its 4 PCI slots allow it to hold up to 32 AE channels, using Physical Acoustics’ PCI-8 AE boards. It has been designed to operate either as a benchtop system via direct connection to a monitor, keyboard, and mouse, or as a remote system controlled by a notebook computer over its Gigabit Ethernet interface.
-
product
Physical Layer Switching Systems for Copper LAN, WAN< DSL, Telco Apps with RJ Style Connectors
RJ Series Switching Systems
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration.
-
product
VeriStand
VeriStand helps you get your hardware-in-the-loop or test cell control and monitoring system up and running quickly. With a wide range of out-of-the-box functionality that includes configurable data acquisition and logging, test sequencing, and simulation model integration, VeriStand reduces the time needed to test your products. You can also use a variety of software tools to add custom functionality to VeriStand, which makes it flexible enough to adapt to even the most complex applications. Choosing VeriStand gives you the confidence that your test system will perform reliably while providing the flexibility you need to meet your real-time test requirements.
-
product
Vehicle Test Chambers
Our dynamometer chambers feature dependable mechanical refrigeration, superior air flow, and expansive control systems. Our dynamometer drive-in vehicle test chambers are designed to integrate directly with a dynamometer system, while simultaneously exposing vehicles to a wide variety of environmental conditions including temperature and/or humidity, rain, wind, and more. Our control systems allow for precise temperature and humidity testing while meeting your exact specifications.
-
product
vibration test system
Labtone Test Equipment Co., LTD
Labtone EV series of electrodynamic shaker vibration test System simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications.Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.Labtone EV series of electromagnetic vibration testing system is specially designed to meet the need for long time operation. Vertical and horizontal vibrations can be achieved by the installation of vibration resistant base. The standard platform is equipped with high efficiency airbag shock isolation device, so that the vibration transmitted to the building can be minimized. There is no need for additional foundation in most of the cases.A complete set of vibration testing system is composed of shaker, power amplifier and vibration measuring control system, in accordance with the relevant national and international standards (such as: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS, etc.) to provide technical support for establishing product quality inspection.
-
product
Generators
Vibration Shock
Software Vibration shock is used for testing specimen resistance to vibration impact. This software is a part of the software complex ZETLAB VIBRO, supplied together with vibration control systems ZET 017-U. The software enables generation of impacts with pre-set parameters and noise presence within a specified frequency range. The software is activated via ZETLAB control panel and VCS menu.
-
product
Group3 Control
Group3 Control is a fiber optically linked control system using distributed I/O modules called Device Interfaces, or DIs. A DI is positioned at the point to be controlled and the appropriate I/O boards added to it from the list below.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm - SPST
40-294-123
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Substation HMI
Schweitzer Engineering Laboratories, Inc.
SEL automation solutions allow you to visualize data and control the system with an integrated, web-based HMI for local and remote monitoring, control, and annunciation for substations or other processes.
-
product
12-Channel VME Current Loop/Process Control I/O Module
V220
The V220 is ideal for driving and sensing transducers in computer or PLC-based control systems. It can also be used to simulate complex industrial processes to control systems under development and certification.
-
product
Cockpit Controls
TRIUMPH Mechanical Solutions produces cockpit controls and quadrants specifically designed to meet unique customer requirements. Our Electro-Mechanical Cockpit modules are frequently married to our push/pull controls to produce combined output devices. For example, a throttle quadrant with switch/transducer outputs and mechanical cable connections to an engine control system.
-
product
Transmission Dynamometers
SuperFlow’s Axiline and Hicklin transmission test stands cover the complete range of light-duty, medium-duty, heavy-duty and cross drive transmissions on the market today. With solutions for everything from passenger cars to the M1 tank and features like mechatronic shift controls, no-hassle precision aligment tooling and the available PowerNet Data Acquisition and Control system for fully automated tests and reports, SuperFlow transmission dynos are the only choice of the top transmission remanufacturers world wide. Check out or custom testing solutions page for examples of custom transmission test stands we’ve built for heavy duty cross drive dynos and full AC regenrative test stands.
-
product
Single-Axis Shaker Vibration Testing
Modular Vibration Control Systems - Scales up to 512 Channels
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 2k
50-265-302
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
