Fuel Cell Stack
-
Product
HDDH-3932 Single Cell Battery Activator
-
HD Power Test Equipment Co.ltd
HDDH-3932 Cell Activator is used to discharge and charge and activate for disable single cell battery, which is simple, safe and accurate test device.The instrument is with perfect protection function, sound and light alarm and clear interface tips.
-
Product
Stack Gas Analyzer
ENDA-7000 Series
-
After decades of experience in precise stack gas measurement, HORIBA's brand new ENDA series represents the ultimate stack gas analyzer. With enhanced lower cost and reduced maintenance time, high sensitivity, and usability, we focused on the users' point of view. The ENDA-7000 is designed to continuously measure the concentrations of NOX, SO2, CO, CO2, O2, and NH3 in stack flue gas streams. The model is offered in dozens of combinations based on your measurement requirements. The ENDA-7000 uses an extractive method which measures undiluted sample gases, and is very suitable to stack gas measurements such as shale gas, LNG, or biogas and other combustion applications. The ENDA-7000 is an excellent choice for measurements in power generation facilities, boilers, furnaces, steel manufacturing, cement plants, pulp and paper mills, etc.
-
Product
Single Point Load Cells
-
These have a range of different platform sizes and are suitable for different applications including bench scales, counting scales and other applications in many industries. Click the links below to find out more about each product and to view specific data sheets.
-
Product
Through Hole Load Washer Load Cell Compression Only
LWO SERIES
-
The LW0 Series are washer shaped, strain gage based load cells that have been most commonly used in fastener testing and thru hole load applications. Our stocked ranges from 2,400 through 300,000 lb compression are made from 17-4ph heat treated stainless steel and are matched to bolt diameters and their specific load characteristics. Modifications of diameters, thicknesses, or load range to a specific diameter for OEM applications are welcomed. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Test Cells
-
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They exceed the requirements of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing. The Cells are a modified form of GTEM cell, using a balanced dual septum design which maximises EUT volume for a given external size of cell, and dramatically improves field linearity. The EUT volume is fully lined in structural polycarbonate capable of supporting heavy products and access is via a large, full height door at the end of the cell. Adjacent to the door is the I/O filter compartment which can be customised to suit the users requirements. USB, RS232, Parallel, Ethernet, co-ax and other product specific filters can be added at time of ordering.
-
Product
Cell Fractionation Filter
CELLNETTA MZM1 Series
-
Cell sorters, magnetic beads, and gravity separation are common cell fractionation methods. CELLNETTA uses the micron size differences of cells to enable conventionally difficult high-precision fractionation and simple cell separation using an innovative fractionation filter.
-
-
Product
Battery Cell Formation System
17000 series
-
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
Rod End Load Cells
-
Our rod-end load cells are designed for integration into tension measurement. They are versatile, durable, and fit easily into small spaces such as inline with vehicle tie rods.
-
Product
Load Cell Displays
-
We carry a wide range of digital displays for strain gage load cells. There are many options available to our load cell displays such as analog outputs to interface with a PLC, digital outputs for computer interfaces, I/O and relay outputs to control batching and checkweighing scales, and wireless load cell indicators.
-
Product
Load Cells & Mounting Kits
-
Load cells are commonly used to measure weight in an industrial environment. They can be installed on hoppers, reactors, etc., to control their weight capacity, which is often of critical importance for an industrial process.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
Product
Basic Fuel Pressure Tester Kit
FIT450
-
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose.
-
-
Product
Mini Load Cells
-
Interface Mini™ load cells are designed for light touch, light weight, and compact applications. Our miniature load cells provide exceedingly accurate measurements similar to our LowProfile load cells that have our proprietary strain gages. All our miniature beam load cells, load buttons, load washers, rod end load cells, S-type load cells, and platform scale load cells can all be ordered in range of different sizes. Capacities are available as low as 0.11 lbf (0.5 N) and as high as 1,124K lbf (5,000kN). A variety of our miniature load cells are designed for off-the-shelf and OEM applications. Our engineers can also work with you to design custom load cells to fit your exact specifications and requirements.
-
Product
Vacuum and Fuel Pump Tester
DVG1
-
Suitable for testing and fault finding the following in petrol engines including: Spark misfires; poor engine compression; weak/rich mixture; ignition over advanced/retarded; inlet manifold and carburettor air leaks; incorrect valve timing; poor fuel economy; balancing carburettors; turbo boost gauge; fuel pump testingDisplay packed.
-
Product
Modbus Stack
softMOD
-
SoftMOD is the industry-standard Modbus protocol stack for industrial automation and building management. SoftMOD supports both Modbus RTU (Remote Terminal unit) and Modbus TCP/IP (Transmission Control Protocol) as well both client and server modes.
-
Product
Load Cell Tester
-
Xiamen Elane Electronics Company, Ltd
Large six-digit LED display < Easy to use and small in size < Accuracy of 0.005%FS/10ppm < 2 channels CH0 : -12mV/V~+12mV/V, with resolution 0.1uV/V CH1 : -1.6mV/V~+4.8mV/V, with resolution 0.01uV/V < Four user selectable output units (N, kgf, lbf and mv/V) < Peak Hold function to capture and holding the peak value for the immediate or later reference < Clear key to clear the peak value < Presence of tare key and foot switch to zero the display (tare function) < Great for monitoring and testing load cell characteristics (repeatability, linearity, creeping, temperature drift, etc
-
Product
Large Telemetry Compressive Load Cell
TC-3.0-LG
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
-
Product
Telemetry Shackle Load Cell
TS-3.0
-
The DLM Telemetry Shackle is a high strength marine grade wireless Load Cell. Manufactured from industry leading Crosby and GN shackles along with a stainless steel load pin, the DLM Telemetry Shackle offers reduction in weighing headroom with the flexibility of 2.4GHz licence free wireless load transmission.
-
Product
Power Module Test Cells
-
SPEA’s Power Module Test Cells are the complete industrial equipment oriented to the production test requirements of IGBT semiconductor power modules for consumer, transportation, energy production, industrial applications.SPEA’s Power Module Test Cells provide a turnkey solution for the automated handling, contacting and testing of these products, with the capability to force and measure the very high current (up to 1000 A) and voltage (up to 2500 V) values required for a complete, reliable test.
-
Product
Heavy Duty Shear Beam Load Cells
SBL SERIES
-
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
Product
Cell Culture & Cell Monitoring Solutions
-
Improve and streamline your cell culture processes with Olympus’ innovative cell culture and cell monitoring equipment. At Olympus, we offer equipment to support processes through a range of cell culture analysis stages, including cell culture microscopes and cell monitoring equipment and software.
-
Product
DAS & Small Cell Products
-
*High power handling 750W Ultra-broadband devices support from 555 to 3800 MHz.
-
Product
Semi-auto 4 Point Probe System for Solar Cell Substrate
RG-100PV
-
*Measurement system for thin film on substrate samples for multi-points measurement*Even pitch and random pitch for Max.1,000 points*2-D/3-D square mapping software for even pitch
-
Product
Load Cell
-
Precise and robust and it has been designed to meet the requirements of a wide range of industrial weighing applications: hoppers, tanks, platforms. Is able to work in severe environmental conditions typical of applications in food, chemical and pharmaceutical industries.
-
Product
PXI Mixed Configuration Relay Module - 1 Cell Populated
40-138-AA-BB-CC-DD (1 CELL)
-
The 40-138 2A Relay Module with 1 cell populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Coin Cell Tester
TOB-5V10mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channel Coin Cell Tester (0.1-10mA, up to 5V) with Laptop & Software for Research. TOB-5V10mA coin cell tester is an eight-channel battery analyzer to analyze small coin cells with a range current 0-10mah, voltage 0-5v.
-
-
Product
Handheld 2G & 3G Cell Phone Detector
SH-055UMW / 10127
-
This new portable Mobile Phone Detector is made for detecting 2G & 3G cellular phones (all current generations and all networks) communication in a place.
