Electromagnetic
See Also: Electromagnet, Energy, Electromagnetic Simulation
-
Product
Electrodynamic Shakers | Electrodynamic Shaker Systems
-
Wewon Environmental Chambers Co, Ltd.
Your product descElectrodynamic shakers makes use of an electro-mechanical assembly to product vibration through electromagnetic force. These electrodynamic shaker systems can precisely generate either single, or multi-axis vibration using sine, random, sine-on-random, or random-on-random accounts. Usually these ED shakers are utilized to figure out the products ability to either run within it’s intended environment, or to target resonance in the product to determine weakness.Any type of product moved by road, sea or air, is subjected to vibration tests throughout its manufacturing procedure. These tests supply essential details relating to the behavior of the manufactured part before advertising and marketing, in order to prevent them breaking in the future.All the vibration tests, both vertical and also horizontal, may furthermore go through temperature as well as relative humidity tests, integrating the vibration test with making use of a climatic chamber. The electro dynamic shakers from Wewon attach to any kind of electrodynamic vibration system. https://www.wewontech.com/electrodynamic-shakers/
-
Product
RFID
-
Leuze electronic GmbH + Co. KG
With RFID, no direct "visual contact" between the read-write unit and transponder is necessary. Information from the transponder is received by means of electromagnetic waves. As a result, these systems can be used practically and reliably under even the most adverse conditions.
-
Product
Resolver Systems and Resolver Sub Systems
TDSM
System
Computer Conversions Corporation
The TDSM Series are low cost absolute encoders consisting of a size 11 electromagnetic transducer and a 2.6 x 3.1 x .6 conversion module. The outputs available are 12 to 16 bit binary format representing 0 to 359.99 degrees of absolute shaft angle input. The transducer reference supply is also included in the module which is designed for printed circuit mounting. A data transfer and data hold line are provided for simple computer or microprocessor interfacing. These features in addition to the latest digital circuitry techniques, make these encoders the best selection in today's applications where resolutions greater than 10 bits are required with ultra high reliability assured.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
Spiral Antenna UHF Trafo
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes Spiral antenna the optimal sensor for direct installation on high voltage Transformers. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces. Contact our sales department for consulting.
-
Product
Current Transformer Tester
HTCT-300
-
Full-featured, can not only satisfy various CT (eg: protection, measurement and TP category) but also PT type electromagnetic unit for its excitation characteristics (ie voltage current characteristics), ratio, polarity, secondary winding resistance, secondary load, ratio deviation, angle deviation and other test requirements.
-
Product
Electromagnetic Flow Meters
-
Magnetic flow meters, also known as electromagnetic flow meters or mag meters, are often selected because they are obstruction less, cost-effective, bi-directional, and highly accurate flow meters.
-
Product
Electromagnetic Simulation Software
EmSlice
-
EMSlice is an EM Simulation Software tool supporting the design, analysis, testing and evaluation of systems involving EM Radiation. Including optical, radio communications, radar, antenna systems, etc.
-
Product
Turntables
-
Used for EMC testing motorized turntables TT-400X and TT-600X are used in commercial electromagnetic compatibility testing as low-profile, above-ground platforms for spinning the equipment being tested (EUT). The turntable can hold and rotate equipment that is on a desk or on the ground. The device is turned so that the position or angle at which the EUT gives off the most electromagnetic interference can be found. By using the switch on the remote, you can turn the turntable in either direction. The motor and the gear reduction drive that goes with it make up the rotation drive. These turntables are made from non-conductive weather proof materials. You can buy any kind of ramp you want to use to move heavy equipment onto the turntable.
-
Product
PSG Vector Signal Generator, 100 kHz to 44 GHz
E8267D
Vector Signal Generator
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
Product
EMC Chambers
-
A specialized, shielded room designed to test electronic devices for radiated and conducted electromagnetic interference (EMI).
-
Product
EMI Test Receiver
SER
-
Saluki SER series EMI receivers comply with CISPR 16-1-1 standard, integrated CISPR-AVG, CISPR-RMS, QPK detectors, and electromagnetic interference measurement. According to CISPR, EN, FCC and MIL standards, which is suitable for EMI testing in home appliances, lighting, automotive electronics, medical, and other industries. Combined with ETR PC measurement software and a wealth of test options, accurate automated testing is possible. The whole system is equipped with a spectrum analysis module and a tracking signal generator to meet the testing needs of users in different fields.
-
Product
TERAHERTZ ROOM TEMPERATURE DETECTORS FROM 37.5 GHZ To 996 THz
-
Insight Product Company offers Golay cells that detect electro-magnetic waves at terahertz frequency ranges from 0.0375 to 996 THz.
-
Product
VLF Electromagnetics
-
VLF surveying relies on radio signals that are broadcast from navigation stations around the world. The principle is that these signals are deflected in certain ways when they pass through conductive ore or water-filled vertical-to-sub-vertial fractures in the earth. By monitoring these deflections, the position and, potentially, size of the target can be determined.
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
SERS (Surface Enhanced Raman Scattering) Substrate & SERS Reader – Mini Chemistry Analytic Pack
-
The porous carbon SERS substrate provides not only high signal enhancement due to its strong broadband charge-transfer resonance for large chemical enhancement (as opposed to electromagnetic enhancement in traditional metal-based SERS substrates), but also extraordinarily high reproducibility or substrate-to-substrate, spot-to-spot, sample-to-sample, and time-to-time consistency in SERS spectrum (which is not possible with traditional metal-based SERS) due to the absence of "electromagnetic hot spots" by making the entire surface of the substrate "chemically hot", high durability due to no oxidization, and high compatibility to biomolecules due to its fluorescence quenching capability.
-
Product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
-
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials.
-
Product
Modeling Capacitors, Inductors, Insulators, Coils, Motors, and Sensors
AC/DC Module
-
The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.
-
Product
Electromagnets
-
To be used in research, or as magnetizers to generate magnetic field strenghts up to 3 T. The airgap can be adjusted via hand wheel. The pole pieces are exchangable. Water cooling is possible.
-
Product
Measurement Technology for Teaching and Training
-
Is particulary suitable for training and further education. With the disturbance emission model, a variety of different experiments which improves one`s understanding of electromagnetic processes in modern electronic engineering are possible. The coupling mechanisms of disturbance emissions are visualized from their sources to the antenna. The impacts of EMC measures are then easier to understand.At VM 251 the electromagnetic d
-
Product
EMI Shielding
-
Parker Chomerics electromagnetic interference (EMI) shielding product family spans a wide variety of uses and applications, including an extensive selection of EMI gaskets, shielded windows, shielded honeycomb air vents, cable shielding products, grounding solutions, shielding laminates, and metal foil tapes. It also includes conductive adhesives, coatings, sealants, greases and inks, as well as conductive plastics.
-
Product
Temperature Data Logger
-
The temperature recording in a process is the most common and widely required application in any process. The commonly used temperature sensors are RTD Pt100 / Pt1000/ Cu53 / Thermistors and different kinds of Thermocouple. In order to avoid electromagnetic interference, the temperature signal is converted to 4-20mA and is carried to the logger. Our range of Temperature Data Logger includes Temperature Humidity Logger, RTD Data Logger, Thermocouple Data Logger and Flameproof Data Loggers.
-
Product
Magnetic Testing Instruments
-
Yuxiang Magnetic Material Ind. Co., Ltd.
Magnetic Testing Instruments for testing electromagnets and automatic hysteresigraph
-
Product
Infraded Temperature Transmitter
Model KM 6816-4 / KM 6816-5
-
Kusam Electrical Industries Limited
With CE approval and protection against electromagnetic disturbance for EU standard
-
Product
Magnetfield Testers
-
The magnetic field tester is suitable for rapid and precise testing of electro-magnetic switches and valves. Their tip lights up to indicate the presence of permanent, DC or AC magnetic fields. Thereby, they are so sensitive that very often it is not necessary to remove covers or cladding from machines and the function check can be carried out without any setting-up time or stopping the machine.
-
Product
VME 19" Rack Mount Industrial Chassis
R2U4S
-
The R2U4S is a 2U height 19'' Rack Mount Industrial Chassis featuring 4 slots of either VME or cPCI 6U size boards. The R2U4S has successfully passed the mechanical, thermal, electromagnetic EMC/EMI qualification tests required by our customers. Its modular design enables to fulfil the requirements of application areas ranging from the environmentally benign right through to deployed industrial, airborne and naval applications. All feature a door to better protect the electronics which is placed inside.
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Electromagnetic Flowmeter for conductive liquids
Picomag
-
Reliable measurement and monitoring of industrial water, cooling water or warm water. Simultaneous measurement of flow and temperature. Flexible integration into all fieldbus systems via IO-Link. Commissioning and operation via Bluetooth® and SmartBlue App. Minimum conductivity ≥20 μS/cm. Fluid temperature –10 to +70 °C (+14 to +158 °F).
-
Product
Electromagnetic Water Meter
WATERFLUX 3070
-
WATERFLUX 3070 is the first battery powered water meter for the drinking water industry that is capable of measuring flow, pressure and temperature with one sensor. Communication via Modbus RTU or pulse.
-
Product
Compact Accelerometer (Shock Meter)
AP2019
-
Can be used as shock sensors in equipment diagnostic systems; Combination of high axial sensibility, intrinsic frequency and shock resistance; Low sensitivity to electromagnetic fields; Low intrinsic noise level.
