Tables
See Also: Vibration Isolation
-
Product
Test Tables / Test Consoles
-
Adaptronic test tables and test consoles are a decisive component of the adaptronic kit for the assembly of comfortable and high-quality test systems for the wiring test of manufactured cable harnesses of all types.
-
Product
Vibration Isolation Tables
-
Probing Solutions offers Vibration isolation tables made by Kinetics and TMC. To order a table, please call PSI at (775) 246-0999, or email sales@probingsolutions.com for a quote.
-
Product
Single-Axis Rate and Position Tables
-
The wide range of potential customer specifications is accommodated by a number of standardized or customized tables. They are distinguished by differing electrical drive technologies (direct drive, belt drive), table tops, motion controllers (COTS, ACUTROL®3000e), and various options (table tops, temperature chambers, accessories).
-
Product
Optical tables
-
The primary goal of a well designed optical table is to eliminate relative motion between components of test system located on the surface of the optical table because such motion can generate measurement errors.
-
Product
Test Tables / System Solutions
-
WEETECH, as a manufacturer of test equipment, offers its customers also a "Ready To Use" test system solution. It consists of the test table, the customer-specific adaptation as well as the test device, and is very quickly ready for use at the customer's site. According to the customer's requirements, the set-up is designed as a system with permanently installed adaptations for the production of constant cable harnesses in large quantities or with interchangeable adapters for the flexible production of different cable harnesses. Depending on the application, a larger table version or a smaller desk version is available. Various interfaces are available for integrating these solutions into a complete production automation system.
-
Product
Crossed Roller Tables (Aluminum & Steel)
-
Del-Tron’s crossed roller tables are known for their high accuracy and exceptional load carrying capabilities. Our crossed roller bearings are available in both aluminum and steel, and the perfect choice for applications where these criteria must be met. Accuracies range from 0.0001” per inch of travel straight line accuracy on our aluminum tables to 0.00008” of parallelism on our steel crossed roller tables and are capable of carrying loads in excess of 2600 lbs.
-
Product
2-Axis Rate and Position Tables
-
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables >
ELCOWIN - Software For 2D-straightness Measurement With Electronic Autocollimators
-
Optik Elektronik Gerätetechnik GmbH
The software ELCOWIN serves for the measurement of straightness, squareness, parallelism of slides and flatness of precision tables by the autocollimation principle. ELCOWIN can be used in connection with electronic autocollimators of the ELCOMAT series from Moeller-Wedel-Optical.
-
Product
Optical Tables with Quad Tuned Dampers for Ultimate Performance
5300 Series
-
It features quad-tuned dampers in each corner to provide maximum stability and minimum response to vibration disturbances. Coupled with broadband damping throughout, our proprietary epoxy bonded steel and honeycomb tables assure unsurpassed rigidity and stability for demanding applications. To protect against leaks and spills, the SPILLPRUF® configuration provides a safety barrier between the top skin and honeycomb interior.
-
Product
Cable Tray Kit For M9018B And M9019A
Y1218A
Cable Tray
The Y1218A is a cable tray kit designed for the M9018B and M9019A. It can be used with both the rack mount kit and the rail kit but, the rail kit is not required. The kit includes a cable tray, feet for using the chassis on a table, and attachment hardware. An M9018B or M9019A that is racked using the cable tray uses 5U of rack space. The tray is compatible with the Y1217A Rack Mount Rail Kit, the Y1215B/C Flush Mount and Y1216A/B Recessed Mount Rack Adapter kits. This tray is not compatible with the Y1270A Front Panel Interfacing Kit.
-
Product
IP67 DC Blocking Splitter Combiner
PD5033
-
INSTOCK Wireless Components, Inc
PD5033 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5033 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
Honeycomb-structure Table
-
King Design Industrial Co., Ltd.
Honeycomb fiberglass surface & honeycomb magnesium alloy surface.
-
Product
IEC60335-1 Electrical Inclined Plane Device
CX-100
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-1 Electrical Inclined Plane Device is designed and manufactured in accordance with IEC60335-1 clause 20.1. The IEC60335-1 Electrical Inclined Plane Device is to determine the stability of electric appliances which are used on a table or on the floor. The IEC60335-1 Electrical Inclined Plane Device consists of a surface and an angle adjusting device, with angles 0~15° adjustable.
-
Product
Display
Data Processing and Result View
-
The program allows to simultaneously download multiple data files obtained by means of ZETLab programs, as well as to view and edit corresponding data in the graphic and table format.
-
Product
Digital Thermometer with K Type Thermocouple Sensor
Model 300
-
this thermometer is a digital hermometer fr use with any K-type thermocouple as temperature sensor. temperature indication follows IEC584 temperature/voltage tables for K-type thermocouples.
-
Product
Temperature Logger For Human Body Range
HBTS 2.0
-
The HBTS is designed to monitor the temperature of parts, gas or liquids associated with intended/unintended heat to the patient. High accuracy and resolution is achieved in a range of 0-75°C. Typical standards are IEC 60601-1 (Table 24), IEC 60601-2-18 (endoscopes), IEC 60601-2-19 (infant incubators), IEC 60601-2-21 (radiant warmers), ISO 80601-2-74 (humidifiers).
-
Product
Light Distribution Photometer Goniophotometer
LCG-1600
-
Shenzhen Chuangxin Instruments Co., Ltd.
LCG-1600 Goniophotometeric System carries out measuring methods of fixed location and rotating luminaires. The measured luminaire is installed on the two-dimension rotating table, using “+” laser to make the luminaire lighting center superposed with the rotating center of rotating table. The mechanical equipment allows turning the tested luminaires around a vertical axis and a horizontal axis. When tested luminaires turn around horizontal axis, the detector which is at the same level with rotating table will measure the intensity of each direction at this surface. When rotating with vertical axis, the detector will measure the intensity at the vertical surface. The vertical and horizontal axis can be rotated continuously at ±180° or 0~360°. According to the measurement requirements, the system can be operated in C-γ coordinates. When getting intensity distribution data, computer will calculate other photometric parameters automatically.
-
Product
Measuring Systems For Beverage Can Manufacture
Tool Cleaning System
-
Optik Elektronik Gerätetechnik GmbH
High performance ultra-sonic device for long life operation. Special cleanser suitable for steel, stainless steel, glass, ceramic, rubber, plastic Removal of strong mineral residues (lime, silicates, phosphates…), grease etc. Customized table made with durable stainless steel. Stainless wire basket for easy handling included. Optional available: special tool inset for punch and ironing dies.
-
Product
UHF/RFID Power Divider Combiner 8-Way, TNC Female, 350-1000 MHz, 30 Watts
PD2981
-
INSTOCK Wireless Components, Inc
PD2981 is a RoHS compliant, 8 way, wideband, 50 ohm, RF power divider, power combiner furnished with TNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 8 way power divider input rating tables for additional details.
-
Product
UHF/RFID Power Divider Combiner 4-Way, BNC Female, 350-1000 MHz, 30 Watts
PD2541
-
INSTOCK Wireless Components, Inc
PD2541 is a RoHS compliant, 4 way, wideband, 50 ohm, RF power divider, power combiner furnished with BNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 4 way power divider input rating tables for additional details.
-
Product
Flow Computers
-
Cox FC30 flow computers service both liquid and gas applications. The FC30 features batching, 40-point flow meter linearization tables, and temperature viscosity correction using Strouhal/Roshko advanced linearization methods and multiple flow and control inputs. Relay outputs are independently assignable for alarms and general purpose warnings. The FC30 has serial communications, both RS232 and 485, and isolated analog and pulse outputs.
-
Product
NI Electric Motor Simulation Toolkit
-
PMSM, ACIM, SRM, and power inverter models for high-performance simulationHigh-fidelity simulations with support for user-defined parameter lookup tables or JMAG-RT models. Open software for full flexibility and customizationLabVIEW project templates to build a software-only simulation and hardware-in-the-loop application. Direct integration with NI VeriStand for configuration-based real-time test. Models for desktop simulation, LabVIEW Real-Time simulation, and FPGA-based simulation
-
Product
Optical Switch
5504
-
The FOD 5504 Optical Switch is a unique handheld instrument for calibration sets and measurement automation. Routine comparison with Master device procedures in calibration laboratories, can be simply performed with before unachievable repeatability. No more need to move fiber and connect it repeatedly. Fix cables on a table, only once clean and connect patchcords.
-
Product
Fully Automatic Close Link Three Phase Energy Meter Test Bench
SY 8320
-
Hong Kong Songyang Industrial Ltd.
Suitable design, good figure. The frame for meters and the body frame are fully made by special aluminum alloy. The table board is composed of fireproofing and heat-proof fiber materials. The whole device is in soft color and good figure.
-
Product
Additional Rotary Axis for High Precision Co-Ordinate Measurement Machines, ISO 10360 Part 3 Compliant
QuadSlimLine
-
Rotary Precision Instruments UK Ltd
Precision rotary axes specifically developed to increase the flexibility, productivity and efficiency of your CMM.Low profile rotary table with an extensive measurement range where typical applications include inspection of rotors, disks, blisks and gears.
-
Product
Rear Cover, G12, Tabletop Configuration
310113421
Protective Cover
The G12 Rear cover is designed to connect to the Receiver in a Table top configuration and act as a mean to hide the cables that are running back to the testing equipment. This works well with applications where the cables are running down to a lower level below the G12.
-
Product
IP X1, X2 Chamber - Drip/IP Test Chamber
-
The drip box testing chambers from Weiber are rain test machines used for testing the outer protection of signal devices, external lighting equipments and car lamps etc. The equipment finds widespread usage in electronics industry and automotive and aerospace industries and is commonly employed for quality testing of products. The test chamber comprises of the guiding upright column, a drip mold, a rotating sample table with adjustable speed and a level meter to allow observation of the level in the drip mold. The equipment uses high quality construction materials for a sturdy construction and is designed for safe and reliable operation. The guiding upright column is made up of high-quality, plastic coated square steel pipe, whereas the drip mold is made up of high-quality stainless steel finish plate undergoing knurling.
-
Product
Cross Voltage Testers
-
designed to perform the 60 Hz power line cross test/AC power fault tests required in GR 1089 issue 6 table 4.5 surge test 3,4, 4.3,and 6, and for UL 1950 section 6.4 paragraph 3 and 4.. Preset and Adjustable Time Settings Measuring Terminals including Voltage Sense and Current Shunt portals provide a safe location for users to accurately measure test voltages and output current while setting up tests. Calibration of the Mini_PT-600 is designed to be performed with a simple handheld multi-meter and the removable Currents Shunts can be easily sent to a calibration laboratory if required.
-
Product
SHOCK TESTER
-
King Design Industrial Co., Ltd.
*Shock amplifier is mainly used to small object, and can reach the pulse duration and high acceleration that shock table couldn’t achieve.*Equipped with shock table or different shock module (the theory is to amplify impact energy through second impact), shock amplifier can reach the requirement of high acceleration.
