Pulse Mask
determines if a pulse signal fits within it's desired frequency band.
-
Product
12 Channels 1.0 ~ 17.0 Gb/s (200Gbps) Pulse Pattern Generator and Error Detector
CA9806-12
-
The UC INSTRUEMNTS CA9806-12 is a highp erformance, flexible 12 channels Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (200 G). It is combined with three sets CA9806 4 CH 1.0 to 17.0 Gbps Pulse Pattern Generator and Error Detector that incorporates an external one by 4 rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build-in 8.5 ~ 15 Gb/s eye diagram testing function.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-3010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±8 kV*High pulse output current up to ±30 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
High Voltage 50 Ω Pulse Generator for CMTI
CMTI-8010A
-
High Power Pulse Instruments GmbH
The CMTI-8010A is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
Product
Tunable, Pulsed IR SW & LW OPO IR Source
Firefly-IR
-
Firefly IR is available in short-wave and long-wave models, providing broad wavelength coverage from 1.4-8.5 µm. The compact and sealed design requires no manual alignment, and can be used in a variety of applications in the lab and in the field. Wavelength selection and scanning is automated and performed via web browser or using a TCP/IP command set. Pulsed operation and high repetition rate provide high peak power and rapid data acquisition.
-
Product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
-
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
-
Product
12-Bit, 2.5 GSPS Digitizer Optimized for Pulse Detection
ADQ32-PDRX
Digitizer
ADQ32-PDRX acquires the input signal via a single connector and uses an onboard splitter to separate the signal into two paths with different gain settings. The high gain path is used to accurately capture low-amplitude portions of the input signal whereas the low gain path ensures the acquisition of high-amplitude peaks without causing saturation. The two signal paths are then combined in real-time inside the onboard field-programmable gate array (FPGA) to create a digitized output with improved performance.PDRX increases the dynamic range by 3 bits and is fully integrated into the digitizer for fast and easy system-level integration. ADQ32-PDRX is therefore comparable with a 16-bit digitizer in terms of dynamic range, but with the benefit of offering a higher sampling rate.
-
Product
Face Masks Particulate Filtration Efficiency PFE Tester
GLE-20
-
GLE-20 is an oil-salt two-in-one Face Masks Particulate Filtration Efficiency PFE Tester. According to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1, etc. It is used to test the particulate filtering efficiency of daily protective masks and medical masks, and to determine the obstruction performance of ordinary fabrics and medical protective masks against a constant flow of airflow.
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Dual Digital Aquisition System For Charge Integration And Pulse Shape Discrimination
DT5790
-
The DT5790 operates upon the DPP-PSD firmware, specially developed for Charge Integration and Pulse Shape Discrimination. DPP-PSD is based on an advanced on line Digital Dual Gate Charge Integration allowing an effective data analysis even at high count rate. It performs input signal baseline calculation, self-triggering and double-gate charge integration with programmable parameters, double integration of both prompt and total charge for Pulse Shape Discrimination and pedestal subtraction for energy calculation.
-
Product
PXIe Precision Source/Measure Unit, 15 MSa/s, 100 FA, 60 V, 3.5 A DC/10.5 A Pulse
M9603A
Source Measure Unit
The Keysight M9603A is a PXIe precision SMU featuring best-in-their-class narrow pulse width as narrow as 10 μs. It enables dynamic/pulsed measurements with up to 15 MSa/s for broad emerging applications such as VCSEL optical devices.
-
Product
4-axis Pulse Train Motion Control Modules
HSL-4XMO
Motion Controller
HSL-4XMO is an advanced 4-axis remote motion control module via HSL bus. Combined with HSL I/O and motion control modules, it can meet many requirements in machine automation (MA) field. HSL-4XMO offers two models - HSL-4XMO-CG-N/P and HSL-4XMO-CD-N/P. HSL-4XMO-CG-N/P is suitable for steppers and linear motors. HSL-4XMO-CD-N/P is suitable for servo motors with transfer cable. Except the advanced motion control library (refer to PCI-8164), ADLINK also provides two extra features for users. Motion Point Table Managements can let users assign the points into the module in advance. Then, users can issue command to continuously move the points without consuming CPU resource. Motion Script Download provides users a easy interface to program the application. With this script, the DSP inside HSL-4XMO can decode the file and execute itself.
-
Product
10 Digit Rate/Batch Counter (Pulse)
CS2-TM-Pulse
-
The CS2-TM(Pulse Input) is innovation totalizer.Adtek builds in high technology with wide input range from 0.01Hz~ 140.00KHz with auto-range function at same unit. There are three setting modes for K factor, 1/K factor and flow speed to match the difference output description of flow-meters.The Totalizer provides high accuracy measurement, display, control and communication (Modbus RTU mode) of Pulse from Flowmeter or encoder, proximity switch, photo switch for length control.There are two display screen and 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, 1 Pulse and RS485 port available. They are also support fantastic control function as like as N, R, C mode for totalizer and batch control.
-
-
Product
4 Channel 24.5~ 29.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808
-
The UC INSTRUEMNTS CA9808 4 Channel 24.5 ~ 29.0 Gb/s (100Gb/s) Pulse Pattern Generator and Error Detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 24.5 Gb/s to 29 Gb/s each Channel. 4 channel 29.0 Gb/s make it total up to over more than 100 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
Transmission Line Pulse Testing
-
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
Product
Medium & High Voltage Pulse Generators (Rise Time > 1 ns)
-
Offer fast medium voltage pulsing with high current capability. These models are ideal for driving solenoids, pulse testing of MOSFETs, and other applications.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Isolation Pulse Transmitter
PA-330Z
-
The PA-330Z receives the square wave signals from the rotary encoder, and converts it to low impedance signals suitable for long distance transmission after wave-shaping and amplifying via photo couplers which provide isolation between input and output.A 12VDC external power supply is provided for use with the DC powered RP series encoder.The case is sealed construction which allows closely mounting to the encoder.
-
Product
Cross-Correlator Pulse Profiling Systems
Rincon
-
The third order cross-correlator is ideal for looking at the full range of output from amplified femtosecond laser systems. High temporal resolution over a long (close to 1 ns) window shows pulse features that are usually missed, giving the user a detailed and complete picture of the quality and stability of the output pulse parameters of their femtosecond lasersystem.
-
Product
USB Power Sensor - 100 MHz to 8 GHz, Average, Peak (Pulse)
GT-8551B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
Pulse Generators
-
Dedicated analogue pulse generators and function generators with true pulse capability.
-
Product
Very High Speed Pulse Generators (Rise Time ≤ 1 ns)
-
The Avtech high speed pulse generator line includes models with rise times as low as 40 ps! Instruments are available in a variety of formats, including DC-powered externally-triggered modules, simple AC-powered benchtop pulsers with knob and switch controls, as well as more sophisticated instruments with GPIB,
-
Product
30A, 50 MHz High Sensitivity Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP030B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Turn Key Laser and LED Sources with Picosecond Pulse and Repetition Rate up to 100 MHz
DeltaDiode
-
DeltaDiodes utilize laser diode and LED technology to generate short optical pulses over a very wide range of repetition rates and wavelengths. Optical pulses as short as 50ps can be generated at repetition rates up to 100MHz.
-
Product
Automated Front & Backside Mask Aligner System
Model 6000
-
With over 4 decades of manufacturing in the semiconductor industry, OAI meets the growing challenge of a dynamic market with an elite class of production photolithography equipment. Built on the proven OAI modular platform, the Model 6000 has front and backside alignment that is fully automated with a submicron printing capability as well as submicron top to bottom front side alignment accuracy which delivers performance that is unmatched at any price. Choose either topside or optional backside alignment which uses OAI’s customized advanced recognition pattern software. These Mask Aligners have OAI’s Advanced Beam Optics with better than ±3% uniformity and a throughput of 200 wafers per hour in first mask mode, which results in higher yields. The Series 6000 can handle a wide variety of wafers from thick and bonded substrates (up to 7000 microns), warped wafers (up to 7 mm-10mm), thin substrates (down to 100 micron thick), and thick photo resist.
-
Product
Single And Dual 32k Digital MCA & Pulse Processor
Hexagon Family
-
Hexagon is a high precision 32k MCA available in single and dual input channel versions. This compact, high performance desktop MCA includes features such as an input stage for signal conditioning, a fast analog-to-digital converter (ADC), digital signal processing algorithms, High Voltage and Preamplifier outputs for detector bias and preamp power. Hexagon is ideally suited for applications using high energy resolution semiconductor detectors such as HPGe, Silicon, CZT as well as scintillation detectors such as NaI and LaBr3. It can manage both positive and negative signals from resistive feedback or transistor reset preamplifier detectors as well as signals coming from PMT anodes.
-
Product
Electrical Fast Transient Pulse Group Generator
SKS-0404IB
-
Shanghai Sanki Electronic Industries Co., Ltd.
Electrical fast transient pulse group generator SKS-0404IB fully complies with the new standards of IEC61000-4-4, EN61000-4-4 and GB/T17626.4; provides pulse test voltage up to 4500V, which can meet various product standards Severity level ; pulse frequency up to 1MHz, and continuously adjustable; imported discharge switch, high precision, long life, good reproducibility; using 7-inch true color touch screen control, convenient for users to directly program and control.
-
Product
Pulse Air-Gun Ionizers
EC-G Series
-
Panasonic Industrial Devices Sales Company of America
With the new Pulse Air-Gun Ionizer from Panasonic, operators can comfortably neutralize static electricity while manually cleaning. The Pulse Air-Gun’s light-weight, ergonomic design combined with an oil and heat-resistant 2m cable makes it ideal for use at the production line.The Air-Gun Ionizer is equipped with a white LED on the front of the Gun to illuminate target objects. It has three air emission modes: long pulse, short pulse and continuous emission. Ionized air can be emitted at high pressure (range 0.05 to 0.50 MPa), neutralizing static charges and removing dust simultaneously and swiftly.
-
Product
Pulse Generator
Traction Wheel Assembly
-
The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies.• Square-wave frequency output, NPN open-collector• 5-28 VDC powered• 1 to 1,270 pulses per revolution (PPR - specify when ordering)• Optional bi-directional (quadrature) output models• 3 models: black neoprene rubber, smooth polyurethane,and diamond knurled aluminum tread
