Pulse Mask
determines if a pulse signal fits within it's desired frequency band.
-
Product
IMPATT Noise Generator CW & Pulse At W-band, 94 GHz :
-
The device consists of two modules, a cable that connects them, and a power cable. The first module (I) contains the power supply (AC 115 V), regime switch mechanism and a generator of a series of pulses. The second module (II) is the noise generator. Photo 1: Module I - Power Supply
-
Product
Pulse Generation Measurement Board
MS 1806
-
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
DC Pulse Current Capacitor
-
Both series can be customized as Low Voltage High Capacitance High Current Capacitors.We can customize Snubber Capacitor as Box type and support other parameters.For 250Vac~900Vac / 400Vdc~1,350Vdc and with higher Current requirement, please refer to our AC/DC Power Capacitors.Different applications can have very different capacitor electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
Product
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse
T3CP500-5
-
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse.
-
Product
High-Power Pulsed Amplifiers
-
High power pulsed amplifiers are capable of providing over 1KW of peak power above 10GHz. These SWaP-optimized, high-reliability products have been designed to withstand the toughest environments. For custom requirements, Mercury leverages its proven building-block design approach to rapidly deliver a solid-state power amplifier (SSPA) for your application.
-
Product
Very High Speed Pulse Generators (Rise Time ≤ 1 ns)
-
The Avtech high speed pulse generator line includes models with rise times as low as 40 ps! Instruments are available in a variety of formats, including DC-powered externally-triggered modules, simple AC-powered benchtop pulsers with knob and switch controls, as well as more sophisticated instruments with GPIB,
-
Product
Multifunction Counter (Pulse Input)
CM1-CT
-
CM1-CT multifunction counter(position) display controller, is design to have 2 pulse input, for proximity switch, photoelectric sensor, encoder etc.. Counting increase or decrease, positioning batch count etc.. display, with External input and Modbus communication port.Multiple types of input mode, trip mode setting to fulfil easy usage and requirement for counter controller. For different requirement, the meter can be with 2 relay or 1 Analogue output or 1 RS485(Modbus RTD mode) communication. (Choose 1 kind of output from the 3 options)
-
Product
Pulse Start Generator for High Pressure Sodium Lamp
LPSG60662
-
The start-up test of the special lights pulse start generator is for lighting class industry such as high pressure sodium, it is according to IEC60662: 2011 and GB/T13259-2005 standard requirements.
-
Product
150 Amps, 10 MHz BW Current Probe - AC/DC , 500 Amp Peak Pulse
CP150
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX52
Frequency Extender
The Keysight N5293AX52 is a broadband frequency extension module designed for use with Keysight’s new PNA / PNA-X-based millimeter-wave solutions. It is a compact, lightweight, and ruggedize frequency extender module with built-in bias tee for pulsed DC bias operation. It interfaces with the Keysight N5292A test set controller. The modules allow users to extend the frequency coverage of a base PNA / PNA-X Series network analyzers to a range of 10 MHz to 110 GHz. For more information about cable and accessories for use with network analyzers, please visit Network Analyzer Accessories.
-
Product
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse
T3CP30-100
-
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse.
-
Product
Pulse Initialization Demo Board
TMR9112
-
MultiDimension Technology Co.,Ltd.
The TMR9112 demo board was developed to support evalution of the TMR9112 single-axis sensor. The demo board comes with the fast bipolar current pulsing circuit needed for initialising the TMR9112 sensor, and it can be powered from a USB port or any external 5V power supply. For user convenience, the demo board has an optional on-board timer clock with four selectable frequency settings. The On-board timer clock and frequency output can be enabled using the jumper pins. This demo board is divisable along the dotted line so that the sensor board can be seperated from the pulsing circuit board.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
Product
Pulse Radar Reference Test Solution
-
Compact Reference Solution with ADP7104, M8195A, WR15CCU, WR15CCD, N5183B combines commercial off-the-shelf COTS modular hardware and software from Guzik, Keysight Technologies, KJ Microwave and Virginia Diodes, which provides a flexible testbed for radar waveform generation and analysis. Generate and analyze pulse radar waveforms. Pre-correct waveforms for overall channel response. Supports many topologies for radar transmitter / receiver testing (IQ, IF, RF, microwave, millimeter-wave).
-
Product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Pulse Acquisition Board
MS 1818
-
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
-
Product
Pulsed IV
AURIGA 4850
-
Pulsed IV (current-voltage) measurements have emerged as the preferred method of capturing current-voltage characteristics of active devices such as field effect (FETs) and bipolar junction (BJTs) transistors.
-
Product
PXIe Source/Measure Unit, 15 MSa/s, 1 PA, 60 V, 3.5 A DC/10.5 A Pulse
M9602A
Source Measure Unit
The Keysight M9602A is a PXIe SMU featuring best-in-their-class narrow pulse width as narrow as 10 μs. It enables dynamic/pulsed measurements with up to 15 MSa/s for broad emerging applications such as VCSEL optical devices.
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
Pulse - Generator
PG 01-2000
-
The test generator PG 01-2000 is suitable for insulation test and testing of the impulse withstand voltage of electrical and electronic electricity meters. The generator produce a standard pulse voltage waveform with 0,1 / 2000 μs.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
Product
Split type Pulse Current Sensor
PCT-06
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Through hole type pulse current sensor.*Pulse current sensor for power demand meter.
-
Product
High Intensity Pulsed Solar Simulator
GEN 2
-
Alpha-Omega Power Technologies, LLC.
The GEN 2 pulsed solar simulator and data acquisition systems can generate over 1,200 suns with a spot size of 12 mm x 12 mm at a rate of 2 pulses per second.
-
Product
Pulse Magnetic Field Generator
SKS-0902
-
Shanghai Sanki Electronic Industries Co., Ltd.
The technical parameters of the pulsed magnetic field generator SKS-0902 fully comply with the new standards of IEC61000-4-9 and GB/T17626.9; the pulse current output of up to 2000A can meet the needs of different user groups; it adopts a self-developed CNC high-voltage power supply, High precision, high stability, long service life; using self-developed high-voltage electronic switch as the main switch, high stability, smooth output waveform; achieving 0°~359° synchronous phase triggering.
-
Product
4 Channel 1.0 ~ 17.0 Gb/s Pulse Pattern Generator and Error Detector
CA9806
-
The UC INSTRUEMNTS CA9806 is a high performance, flexible four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (consult factory for higher or lower operation speeds). It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build‐in 8.5 ~ 15 Gb/s eye diagram testing function.
-
Product
Xenon Long Pulse Solar Simulator Three Target Sizes
-
Complies with IEC60904 Class A solar simulation standards.Up to 100ms of effective irradiated time is achieved. Through our proprietary filter technology, spectral concordance conforms to IEC / JIS Class A standards.Three systems provide a wide selection to meet your panel size, floor space, and performance requirements.
-
Product
Pulsed High Field Magnetometer
TPM
-
This is the equipment evaluating the magnetic properties of rare-earth such as Js, Jr, Hcb, Hcj, (BH)max, HK and SR etc.
-
Product
30 A, 10 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 3 Meter Cable
CP030-3M
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
