Showing results: 1396 - 1410 of 1719 items found.
-
Electrak Pro -
Thomson
Thomson introduces our Electrak Pro Series of linear actuators. This family stands alone when it comes to the toughest and most demanding applications. Available in 12 or 24 VDC models with customizable stroke lengths up to 300 mm (12 in), these units can push or pull loads up to 4448 N (1000 lbf) at speeds of 20 mm/s (0.8 in/s) and hold loads up to 9000 N (2000 lbf), or contact our factory for longer strokes or higher loads. When space is scarce, where dust, dirt, and water are abundant and when solid, reliable and maintenance-free operation is a must - Electrak Pro is the answer.
-
A694 -
AGM Elettronica
The A694 is a short circuit locator designed for fault location in metallic cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A694 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 0.1 ohm and less than 40 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
Model MMW-1A -
Jinan Testing Equipment IE Corporation
The MMW-1A UTM for Friction Wear can simulate rolling, sliding and rolling & sliding combined movement under the certain contact pressure to complete point, line and plane simulating tests. The UTM for Friction Wear can be used to evaluate the friction wear performance of lubricant, metal, plastics, coating, rubber, and ceramics etc. The UTM for Friction Wear can not only satisfy the needs of traditional petrochemical industry to research, develop and inspect the various kinds of intermediate & high grade hydraulic oil, combustion engine oil and gear oil, but also can simulate evaluation on new material development and new technology research under dry condition.
-
285 HD -
Standard Electric Works Co., Ltd
● Three different ranges of identification of AC voltage: 285-A HD : 3~7 kV 285-B HD : 6.6~11 kV 285-C HD : 10~22 kV● The LCD will "flash continuously" for high voltage testing.● Physical contact with electrical conductors is not nec- essary when testing for live wires.● The 285 HD senses the radiated field that surrounds live conductors.● Radiated field strength increases with voltage and decreases quickly with distance.● Large LCD.● Continuous monitoring.● Easy to install.● No batteries required.● Weight : Approx. 80g.● Meets EN 61326-1 EN 55011 EN 61000-4-2 EN 61000-4-3
-
GR Series -
Test-X Fixture Products
The 3210 Series Receiver is designed for interfacing the GR 2270 style test fixture. Using patented CAM/TRAC design, the 3210 Receiver provides an accurate, positive locking system that ensures consistent contact throughout the entire interface. With a 5/8" stroke, the 3212 Receiver allows additional clearance for coax and custom block applications.
-
DU3315A/3316A -
Delta United Instrument Co., Ltd.
Real-time Open Check of the alarm and signal output of no contact signal3 in 1 tester with AC, DC, IR functions ( IR function is optional for DU3316 only)ARC Detction:DU3315A /DU3316A Standard function40 x 4 LCD text displayFast cut-off time : 0.4ms5 sets of memory, 3 steps for each memory
-
MicroContact AG
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
Radiometer Physics GmbH
Our Vector Network Analyzer Extenders (VNA Extenders) allow high performance frequency extension of vector network analyzers into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. Contact RPG to discuss VNA Extender configurations that will gain the best performance for your application.
-
HopeTech
insulation resistance tester is an instrument for measuring the insulation resistance of components and equipment. Using constant voltage test method, the voltage output range is 25 ~ 1000V, and the maximum output current is 1.8mA. It also has contact anomaly detection function and short circuit anomaly test function, the fastest test time is up to 50mS.
-
Model 7650A -
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
Mors Smitt Group
*Heavy duty Elkonite contact tips*AC and DC versions available*AC versions available with or without internal rectifier PCB*Automated vision system and operator inspection*Comprehensive automated end of line testing*Test Certificates supplied with each relay*Certificate of Conformity supplied with each order*Recertification and repair services available
-
CBA 2000 -
Altanova Group
CBA 2000 diagnostic system is designed to grant the highest accuracy while testing circuit breaker. It can perform static and dynamic contact resistance measurement and it’s a precise timing speed and motion analyzer. Circuit breaker timing test set CBA 2000 is the perfect solution when a complete and reliable diagnostics has to be performed on circuit breakers.
-
TDR9100 -
Doble Engineering
The Doble TDR9100 is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.The TDR9100 provides main contact timing, motion, resistance and capacitance measurements with the flexibility to double or triple your usable channels.Use this inclusive, rugged and field-portable instrument for simple and complex testing of circuit breakers.
-
Mors Smitt Group
*Heavy duty Elkonite contact tips*AC and DC versions available*AC versions available with or without internal rectifier PCB*Automated vision system and operator inspection*Comprehensive automated end of line testing*Test Certificates supplied with each relay*Certificate of Conformity supplied with each order*Recertification and repair services available
-
Aero Nav Laboratories, Inc.
HASS consists of high and low temperature and 3 axis vibration testing performed either individually or in combination.Highly accelerated stress screening is a technique for identifying process flaws in equipment during production. HASS subjects equipment to overstress conditions but at a level which does not affect design life.For assistance in designing a HASS test program contact the laboratory.
