Cards
See Also: Extender Cards, Probe Cards, POST Cards, Test Cards, Boards, Modules
-
product
3 Pin Power D-Type Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize an 3-pin power D-type connector.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm With SPDT
50-293-124
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
Ethernet Switch
SWI-22-10
Curtiss-Wright Defense Solutions
The Parvus SWI-22-10 is a rugged Commercial Off the Shelf (COTS) Gigabit Ethernet switch card optimized for size, weight and power (SWaP) sensitive embedded military and civilian computer network systems applications.
-
product
PCIe Based FPGA Processing / Acceleration Card
iWave’s PCIe based FPGA Processing / Acceleration Card is a half-length PCIe x4 card featuring a high-performance user-configurable Xilinx® Kintex®-7 FPGA enhanced with high-speed memory and a high-throughput serial interface. Front I/O adds dual SFP ports, 1x HDMI1.4a IN, 1x HDMI1.4a OUT. All of these features combine to make the card ideal for a wide range of applications such as Edge Computing, ARINC818 Avionics Video Bus, Acceleration.
-
product
PCI 2 Amp Multiplexer, Single 32-Channel, 1-Pole
50-635A-101
The 50-635A-101 is a single 32-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Type 12R2, 9U, 19" Rackmount, COTS MIL-Rugged
12R2-9U-PC
The 9U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock-isolated versions attenuate 25G shock to the chassis to less than 10Gs at the card cage.
-
product
XMC Processor Cards
Curtiss-Wright Defense Solutions
Our XMC mezzanine cards provide an easy way to add processing power and meet performance requirements within the most demanding size, weight, and power (SWaP) constraints. Create a zero-slot solution by mounting the mezzanine on a graphics or FPGA card or on the power supply of a Curtiss-Wright 3U or 6U computing system.
-
product
6U CPCI Multifunction I/O Board
78C1
The 78C1 is a universal 6U cPCI Multifunction I/O Board that eliminates the complexity and size constraints of using multiple, independent, single-function cards. This single slot card has six module positions, allowing developers to achieve a custom configuration with any combination of function modules, such as A/D (10-channels), D/A (10-channels), Discrete I/O (16-channels), TTL I/O (16-channels), Differential Multi-Mode Transceivers (11-channels), RTD (6-channels), Synchro/Resolver (4-channels), LVDT/RVDT (4-channels), and Signal Generator (4-channels).
-
product
VPX/open VPX C-Frame 5 Slot 3U
Our 2nd Generation C-Frame offers the next level of flexibility in VPX development platforms. Not only can the customer exchange the type of card guides (convection, conduction, AFT) in a blink of an eye but now also the signal backplane. Thanks to Bi=/=Plane®technology, power and signal parts of a VPX backplane are separate PCB assemblies. This enables uncompromised signal quality along with faster turn around for the design of custom profiles.
-
product
128-Channel Scanner/Multiplexer PXI Card
GX6264
The GX6264 is a 6U PXI scanner / multiplexer that plugs directly into an PXI or CompactPCI backplane. The GX6264 provides either differential or single-ended scanning capability, configurable via software commands or DIP switches.
-
product
RWR ATE MKII
MS 1111
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
product
PCI Express Mini Card Adapter for PCIe Slots
PCIe-mPCIe
The PCIe-mPCIe Adapter is a practical solution for system developers when the target embedded system platform is not yet available, but our PCI Express mini card I/O board is, and you need to get started developing and testing the hardware and software.
-
product
Intelligent Interface Card
IIB-1553-PC104
The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard
-
product
Motion Control Solutions
DDC offers a complete line of Synchro/Resolver instrument-grade cards and test equipment including angle position indication and simulation, plus a variety of hardware and software to meet today’s civil, military, and COTS/MOTS requirements. DDC is a leading supplier of Synchro/Resolver-to-Digital and Digital-to-Synchro/Resolver components—the smallest, most accurate synchro/resolver-to-digital and digital-to-synchro/resolver converters available today. Most of these single chip and hybrid converters are based on ASIC designs, yielding the most reliable and affordable converters ever offered, and are the building blocks for DDC’s card-level products.
-
product
20mA/RS232/422 Strobe Mux III Card, Panel & Power Supply
9565-32CPP
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25mm).
-
product
Dual Channel Clock Driver Card
PI-41400
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
product
IRIG Timecode Receiver and Generator
RG1
The RG1 Time Code receiver synchronizes to IRIG-A/B/G time codes and provides precise time in a memory register, for the host SBC.The IRIG output of the card can be used to synchronize other IRIG time code readers. Additionally, the RG1 includes a real-time clock (RTC) that may be used as a reference source for IRIG master applications, to free the system processor from the task of updating the master timer.
-
product
VPX Interposer
VPX850
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
product
6U Vertical Card
440
VECTOR Electronics and Technology, Inc.
Chassis for vertical card installation
-
product
PCI Express 4 CEM Receiver Test Automation
N5991PC4A
The N5991PC4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 4.0 CEM Add-In Cards and systems
-
product
GPIB PC/104 Interface Card & Cable
GPIB-PC104-XL
The ines GPIB PC/104 interface card uses the enhanced features of the ines GPIB chip , resulting in a reliable solution for industrial measurement.
-
product
VME Intelligent Interface Card
IIB-1553-VME
The IIB-1553-VME is an intelligent interface card for dual redundant MIL-STD-1553 applications.
-
product
1-Channel DAQ Module
FMC160
Sundance Multiprocessor Technology Ltd.
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC160 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5960-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
Protocol Analyzer / Jammer for PCI Express 5.0
Summit M5x
The Summit M5x is Teledyne LeCroy's PCIe/ NVMe Jammer solution and is the latest protocol analyzer targeted at high speed PCI Express 5.0 I/O-based applications such as workstation, desktop, graphics, storage, and network card applications.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 65.5k Ohm - SPST
50-294-133
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Precision Multi-Functional Manometer
DM 9600
Large 2.8” Color, touch screenTemperature compensated pressure sensorAutomatic zeroing for long-term stabilityTwo (2) K type thermo-couple socketsSimultaneous display of pressure and temperature readings1000 points and 500 sites data memoryMicro SD card slotUSB charging and data downloadHands free operation via magnetic back case20-hour Lithium battery
-
product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB109
The FAB109 features a PICMG 1.3 CPU card slot, one PCIe x16 slot and three PCIe x1 slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB109 is compatible with Axiomtek's AX60501 and AX6052 chassis.
