-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
-
Product
Computer Based Audio Component Test System
DATS V3
-
Rugged aluminum housing with detachable test leads and built-in precision calibration resistorTighter tolerances on internal components for more precise measurementsIncreased output capability means greater separation from the noise floor, resulting in more accurate measurementsDATS Linearity Test for comparing parameters and impedance plots at multiple drive levelsOptional under desk mounting brackets included to save desk spaceOnly 1" H x 2-1/2" W x 4-1/8" D for easy portability
-
Product
High Power Laboratory Testing System
FTF-HP
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery PacksBi-directional DC power supply
-
Product
Pneumatic Bidirectional Vertical Shock Test System
KRD17 series
-
KRD17 series pneumatic bidirectional vertical shock test system is the novel designed and developed for large specimens that cannot or are not easy to turn over, especially adopt for battery testing. It can complete vertical upward and downward shock test in one test stand without moving the UUT.
-
Product
High Voltage Test System
CKT1175-15
-
12.5 mV – 2000 VDCIR measurements to 5000 megohmsHipot testingDwell time prog. from 1 ms to 1000s in 1 ms steps
-
Product
High Current Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Product
Rotor Test Systems
-
Automation Technology's RTS-3800 Rotor Test Systems offer an unparalleled ability to test the quality of die cast or PM rotors. The RTS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems; the RTS-3800 is backed by ATI's industry leading two-year limited warranty.
-
Product
Semiconductor & Electronic Systems Test and Diagnostics Services
-
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
Product
Grid-Connection Testing System
-
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
Product
Electrolyzer Test Systems
-
Advanced Test System for Research & Development of PEM Electrolyzers
-
Product
Mezzanine System Carrier
MMS6245
System
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
Product
Robotic Cell for Testing Car Multimedia System
-
It is necessary to develop an automated system for testing a multimedia device. The system should perform functional testing: testing of physical buttons, touch screen and logic of operation.
-
Product
eBIRST™ – Switching System Test Tools
-
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
Product
VX4 System
PrecisionWoRx
-
The PrecisionWoRx VX4 System gives test facilities and probe card manufacturers the ability to confidently test tighter pitches and smaller probe tips. The system can be easily configured to specific requirements for a variety of probe card technologies. For processes using cards with very small probe tips, the system’s high-resolution optics deliver a detailed field-of-view for high accuracy and repeatability.
-
Product
Battery & Electrical System Testing
12-0200
-
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
Product
SIP-90-2 Test System Interface Probe
SIP-90-2
ICT/FCT Probe
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
NFC Physical Layer Test System
IQnfc+
-
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
Product
PXI - Test System
-
We provide a complete PXI test system made by PXI individual components: 19'' rack, Measuring and stimuli cards, Relay cards, Power Supplies, Integration additional protocol cards such as CAN and CANopen, Boundary Scan, Integration of additional test hardware
-
Product
Instrument Transformer Test Systems
-
Our systems for testing voltage (VT) and current (CT) instrument transformers are conceived among other things for testing accuracy and insulation.
-
Product
Automated Test System
-
Automated Test System is a production-ready solution that combines test software and various hardware for validation test in both manufacturing and R&D. The solution provides a high performance and cost-effective system based on National Instruments technology.
-
Product
Test system for Electronic Device
PCB
-
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
Product
4 Quadrant Dynamometer Test System
-
Magtrol’s 4 quadrant motorized dynamometers provides expanded testing flexibility over a typical braking dynamometer. With the ability to bring the motor under test (MUT) to synchronous RPM before beginning a test, repeatability is improved. Since the motor windings are at ambient temperature before starting a ramp test, wattage is more consistent.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Test Systems
Test System
Ball Systems delivers best-in-class automated testing systems, software programming, integrated manufacturing systems, and industrial engineered solutions. Our team has former corporate test engineers, quality assurance engineers, industrial engineers, and test managers who have decades of experience to assist customers in meeting their automated test challenges by offering:
-
Product
DC Voltage Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
DC test systems are used to test components and complete systems found in electrical power supply systems and operating on DC voltage.
-
Product
High Current Discharge Testing System
DTV
-
Cold Crank Testing to industry standards: IEC, SAE, BCIDischarge capacity performance testing to thousands of amperes
-
Product
Ultrasonic testing / UT System
-
Xiamen IDEA Electronic Technology Co., Ltd.
IDEA-UTXX Intelligent Digital Multi-channel Ultrasonic detector uses the most advanced digital electronic technology and ultrasonic technology.With utilitarian function,steady performance, easy operation and favorable price, which is the full-digital intelligent ultrasonic detector that has the excellent price versus performance ratio.
-
Product
Mobile Test Systems
-
The systems include A+A+A+ LED solar simulators, high-resolution electroluminescence testers and various other tests that you can easily integrate into your transport of choice or directly into a container on site.
-
Product
TDR Test System
GATS-310
-
The GATS-310 TDR test system provides you with the ability to test nets as down to less than 1/2" in length using Industry Standard Techniques.
