Linearizer
-
product
Function Generator
FG-52
*0.05Hz ~ 5MHz FUNCTION GENERATOR*LINEAR / LOG SWEEP FUNCTION*DUTY CYCLE COUNTROL*INVERT FUNCTION*AUTO RANGE AUTO GATETIME COUNTER*0.001Hz COUNTER RESOLUTION
-
product
Hydrophones
Operating principle of the hydrophones by ZETLAB Company is based on the piezo-electrical effect, which allows to use them as linear and reversible hydroacoustic transducers. The hydrophones by ZETLAB Company meet the requirements of sound environment non-distortion, wide frequency range, and non-directedness.
-
product
Wide Band Filters (multi-octave)
ERF-5W™ Series (Single & Dual)
The new ERF-5W™ filter takes Pole/Zero’s MINI-ERF® technology to a higher level of RF power handling, with 5W (average) in-band power handling, and covering the entire military tactical radio tuning range of 30-520 MHz in one integrated package. This tunability is accomplished by the use of three poles of selectivity, multiple internal tunable filters along with high performance PIN diode RF band select switches. The tunable filters are designed to minimize size and power consumption, while maintaining high RF power handling and linearity characteristics. Serial control is accomplished via a standard Serial Peripheral Interface (SPI)-based bus.
-
product
Arbitrary Waveform Generators
AWG-8200
The AWG-8200 is an agile waveform generator designed for linear frequency chirp, CW burst , and arbitrary waveform applications. It is based upon a modular programmable digital signal processing baseboard engine with an integrated 32-bit processor, high-performance FPGA, and two versatile daughtercard ports that can be clocked up to 1 GHz. Communication to the baseboard is provided by Ethernet and RS-232 ports for programming waveform and control parameters.
-
product
Modulation Distortion Up To 26.5 GHz
S930702B
S930702B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 26.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930702B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
Pulse Generator
Traction Wheel Assembly
The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies. • Square-wave frequency output, NPN open-collector • 5-28 VDC powered • 1 to 1,270 pulses per revolution (PPR - specify when ordering) • Optional bi-directional (quadrature) output models • 3 models: black neoprene rubber, smooth polyurethane, and diamond knurled aluminum tread
-
product
Actuators
Astronics PGA actuators deliver the smoothest kinematics. They can install in any type of seating thanks to a wide range of linear, rotary and compact actuators that add value to passenger experience and comfort.
-
product
E-Series Average Power Sensor
E9301B
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm10 MHz to 6 GHz frequency coverage for Wireless Comms formats Low SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
product
Liquid Flow Controllers
LC-series
Alicat Scientific, Incorporated
The LC-series liquid flow controller uses Alicat’s patented laminar flow design to provide users with fast, accurate, and stable volumetric flow control for water or selected other liquids (see Quick Specs below). At the heart of Alicat’s LC-Series liquid flow controllers is an internally compensated, laminar differential pressure measurement technology that yields linear results over a wide flow range.
-
product
Cable Reel Sensors
AMETEK Sensors, Test & Calibration
Cable Reels can be used as a linear position sensor in any industrial application to monitor a linear or reciprocating machine motion. The system consists of a heavy duty spring motor assembly attached to a precision machined cable drum. As the cable is pulled off of the drum, the drum rotates a rotary position sensor.
-
product
DC Actuators
Electrak DC
Thomson offers Electrak Linear Actuators in DC power versions. With added features and performance capacity, these products follow the quality reputation of our previous designs. From standard to customizable stroke lengths, clevis to trunnion mounts, ball or acme screw drives, and a variety of DC control options, Thomson can provide a fit for just about any application requirement.
-
product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module, 2-Banks
41-670-003-AABBCC
The 41/43-670-003 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
product
Linear Power Supplies Programmable, Local or Digital Control, Ultra Low Ripple/Noise
Series MBT-G
Kepco's MBT-G series (denoted by suffix "G") are bench-style instrumentation power supplies that offer a choice of control methods including direct entry keypad, slew up/down keys, rotary controls and three communications ports: IEEE 488.2, RS 232 and Kepco's single address, multiple instrument long range serial bus. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
Fan In/Outs
The 4601 Model is a Non-blocking Full Fan-Out (any input connected to any output simultaneously) coaxial switch system operating from 1 GHz to 18 GHz. The system is configured with maximum (8) N-type inputs and (8) SMA-type outputs. All inputs are outfitted with high linearity amplifiers in order to compensate for system insertion loss.
-
product
Open Optical Encoders
An optical encoder is an electromechanical device which produces an electrical signal output proportional to the linear displacement of a linear guide or the angular position of an input shaft.Open encoders are exposed and feature no external integrated enclosure. The advantages of open optical encoders include the effective elimination of backlash, shaft wind-up (torsion) and other mechanical hysteresis errors.A rotary open optical encoder consists of a position measurement readhead and an accurate rotary scale marked either on the periphery of a ring or on the face of a disc.The readhead measures position by optically sensing the regularly-spaced scale markings and outputs this information as an analogue or digital signal.The signal is subsequently converted into a position reading by a digital readout (DRO) or motion controller.
-
product
L.V.D.T Products
Columbia Research Laboratories
Columbia's L.V.D.T.'s are designed for the most demanding high temperature military and industrial applications where maximum life under adverse conditions is required. The corrosion resistant stainless steel housing provides effective shielding to contain the magnetic flux within the transformer, as well as providing protection against external magnetic fields. Conservative design permits the use of these transducers well beyond their specific linear range with minimum loss of accuracy.
-
product
Rod Style LDT
AMETEK Sensors, Test & Calibration
Rod Style Linear Transducers play an important role in providing positional feedback, they are proximately used with hydraulic and pneumatic cylinders to report their position back to the host controller. They are designed to be inserted into a cylinder and are capable of withstanding the high pressures associated with hydraulic cylinders.
-
product
Analog Input Modules
The modules provide direct connection to a wide variety of sensors and annunciators. They perform all signal conditioning and linearization and contain no pots or DIP switches. All user-selectable settings, such as ranges are stored in nonvolatile EEPROM, which maintains these values even after power is removed.
-
product
2 Ch Linear Vibration Motor Tester
BK2120C
the BK2120C runs up to 4 vibration sweeps, which you define, to check whether your linear vibration motor is within the limits you set. And now you can set up your own feedback so it's even easier to determine the class of pass or the reason for failure. You still get fast, high quality testing for your linear vibration motors on the product line. And it's still versitile enough to be used for QA or QC as well.
-
product
Dual Channel High Voltage Linear Amplifier
F20AD
This unit contains two independent F20A amplifiers that share common ground reference and power supply.
-
product
RF Bidirectional Amplifiers
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
product
Strain Sensors
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
-
product
Manual Vision Measuring Machine
Sinowon Innovation Metrology Manufacture Ltd.
High precision marble base and pillar ensures the high stability of vision measuring system; High precision toothless rod and fast moving locking device ensures repeatability error is less than 2um;High precise working stage with 0.5um optical linear scales ensures the accuracy is less than 2.5+L/200um;High definitive detent zoom lens and high resolution color camera ensures clear image without distortion;With programmable surface 4-ring 8-division LED Cold Illumination and contour LED telecentric illumination and built-in intelligent light adjustment, it can automatic control the brightness in the 4-ring 8-division.
-
product
Lake Variable Area Flow Meters
Lake Variable Area flow meters, often referred to as rotameters, measure flow rate of a liquid or gas by relating linear displacement of an internal “float” or sharp-edged orifice plate (Lake) to a corresponding flow rate. As flow rate increases, the orifice area that the flow moves through also increases – thus, the term “Variable Area.” Variable Area meters either allow flow through a peripheral orifice formed between a tapered wall and a float as in the traditional rotameter, or an annular orifice and an internal tapered metering pin in the Lake Monitor.
-
product
SWaP+C Optimized HOT FPA MWIR Camera Module
Neutrino® SWaP Series
The VGA-resolution Neutrino LC and newly-released SXGA-resolution Neutrino SX8 provide best-in-class MWIR imagery and data in a small, lightweight package. Based on Teledyne FLIR’s High Operating Temperature (HOT) FPA technology and linear micro-cooler, SWaP series OEM camera modules are designed for ruggedized products requiring long life, low-power consumption, and quiet, low-vibration operation. Both are ideal for small gimbals and airframes, handheld devices, security cameras, targeting devices, and asset monitoring applications.
-
product
Cryogenic Coolers
L3 Cincinnati Electronics (L3 CE) produces a full line of cryogenic coolers to control thermodynamics. Linear cryogenic coolers provide "on-demand" refrigeration that meet your exact needs. Proper cooling delivers long system life, increases operating efficiency and saves power. Whenever a thermal constant is required, cryogenic coolers offer a dependable solution.
-
product
Isolation Amplifier Digital Output
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
product
Linear Detector Arrays (LDAs)
X-Scan H
This digital end-to-end solution is built on a proven concept enabling easy integration, and accelerated development time of X-ray systems. X-Scan H series has high radiation hardness extending lifetime of detectors significantly, and reducing total costs. The series is available in several standard lengths easily scalable to various configurations.
-
product
Precision Stage with Linear Piezo Drive
M-664
Physik Instrumente GmbH & Co. KG
Self-locking, with no heat generation at rest. Excellent start/stop dynamics. Crossed roller bearings. Non-contact limit and reference point switches
-
product
Tower Mounted Amplifiers
*Available twin and single TMA configurations*Low band, high band & dual band units, including AWS & WCS*High linearity, dual duplexed, light weight design*AISG 2.0 compliant
