Test Fixtures
UUT interconnect interchangeable with tester.
See Also: Fixtures, Mechanical Fixtures, Vacuum Fixtures, ATE Fixtures, PCB Test Fixtures, Board Test Fixtures, Bed of Nails, Spring Probes, Test Jigs, Test Probes
-
Product
In-Line / Board Handler
-
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
Product
Wireless Test Fixtures
-
At Forwessun, we have vast experience in designing and delivering wireless in-circuit test (ICT) fixtures. We have experience in providing fixtures tailored to the unique needs of various different industries. While our primary customer focus has been on full and half-bank fixtures for the HP3070 system, we offer bespoke solutions for other platforms as well including GenRad, Teradyne, and SPEA systems.
-
Product
Structural Durability Products
-
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
-
Product
GPS/FMS Universal Test Fixture
TA-3000
-
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
-
Product
Keying Pin Kit, Receiver/ITA
310118112
Keying Pin Kit
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
Product
Test Fixtures
-
REINHARDT System- und Messelectronic GmbH
Is a fixed state of a set of objects used as a baseline for running tests. The purpose of a test fixture is to ensure that there is a well known and fixed environment in which tests are run so that results are repeatable.
-
-
Product
LED Light Tester
-
The T100L Automatic LED Light Test Equipment is designed to identify the presence of any defects of electronic components for LED light applications, addressing any high-volume production testing challenges without needing expensive test fixtures with fiber optics
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
Brake Test Systems
Giant 8000 Series
-
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
Product
3-Component Quartz Force Rings And Links
-
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
Trackside Equipment
-
The Automotive assembly track lineside environment requires numerous amounts of tooling & equipment to ensure build phases are completed productively. Jackmark Engineering provides a wide variety of custom designed trackside jigs & fixtures, test leads and assembly aids including validation tooling to various assembly departments from HVAC to end of line.
-
Product
Customized Test Fixtures
-
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A, Hardware Interlock
40-192A-012-HI
Fault Insertion Unit
The 40-192A-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test:
-
Product
Safety Test Panel for Mixer
-
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
Electrical Tester
R580
-
Nidec-Read's R580 Electrical Tester provides an affordable test system for your bare board electrical test needs. You can easily integrate the R580 with your existing manual test fixtures or select from several fixture options from Nidec-Read. The R580 is supplied with opens/leakage test ability. In addition, you can include other advanced electrical test techniques.
-
Product
CamTrac Z-Axis Test Fixture Kits
CT Serie
-
The CT Series Mechanical Kits, utilizing the patented CAM mechanism1, offset the same precision linear motion. The 'Z' axis motion is ideal for a larger point count mechanical test applications.The CT Series features a hinged 3/8" FR4 probe board, tooling holes for precision alignment, removable sides, precision shafts and cam slide block assemblies, and a pan latch assembly.
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Parallel Electrode SMD Test Fixture
16192A
Test Fixture
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Deep And Sloped Pan Fixtures
-
Line of deep and sloped pan fixtures for general purpose/system non-specific pcb test applications. H+W Test Products manufactures test fixture products for in-circuit, functional and combinational testers for users of automated test systems (ATE) such as Aeroflex, Agilent (HP), Checksum, Factron, Teradyne (GenRad), Test Research (TRI) and Testronics.
-
Product
Sample Preparation
-
Careful attention to specimen preparation is critical to obtaining top quality test data. Pacific Testing Laboratories has, what it believes to be, the most extensively equipped machine shop in any commercial laboratory. Its function is dedicated to fabricating test specimens and fixturing. Principal equipment includes diamond coated tooling, surface grinders, milling machines, lathes, a 30 ton precision press, laboratory presses, and a 4-axisCNC milling machine.
-
Product
Modular Design & Modular Design
Rand R&D Clamshell
-
New HDPE plastic plates for extra easy machine ability and upgradeability. Designed for Research & Development and Pre-Production where product engineering changes are a weekly issue. The primary design focus is easy upgradeability. In R&D and Preproduction, design changes can happen every week. This fixture unlike normal test fixtures was designed to be easily taken apart and updated. Disassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for machining, drilling and wiring updates.
-
Product
EAOC, Electric Servo Drive
-
The AOC-E module is an electric servo drive for the automated opening, closing and contacting of mechanical or vacuum test fixtures, aimed at optimizing work processes and increasing productivity.
-
Product
Test Fixture and Test Programing
-
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
Product
6TL29 Semi-Automated Test Platform
AQ377
Test Platform
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 9,30 kg
