References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
Product
Spectrum Analyzers
SK4M Series
-
*Frequency range: 100 Hz to 20/50 GHz*DANL < −165 dBm/Hz*Low Phase Noise −125 dBc/Hz at 1 GHz signal from 100 kHz offset*High Frequency Reference Accuracy ±0.1 ppm*Resolution Bandwidth Range 1 Hz to 10 MHz*Built-in Low-noise Amplifier
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SFF
Model 6350
-
- Now available in RFSoC Gen 3 with the Model 6353- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
RTSI Bus Cables for 5 PCI or AT/ISA Devices
776249-05
BUS Cable
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
Product
60 GHz WR-15 Waveguide Tx Module
PEM010
-
The PEM010 is a highly integrated millimeter wave transmitter that covers the 60 GHz global unlicensed spectrum allocations packaged in a standard waveguide module. Transmitter architecture is a double conversion, sliding IF with wide bandwidth capability through the up-conversion chain from baseband to carrier. The I/Q interface accepts analog baseband signals which provides for flexibility in design and applications. The baseband input optionally supports FSK/MSK modulation for non-coherent applications. The transmitter incorporates a complete waveguide interface with low-loss transition between the chip and the WR15 waveguide port. The integrated package is small and lightweight, with a simple to use multi-pin ST4 connector for power, reference clock, digital control port and baseband signals. Either of two reference clocks can be used for setting 540 MHz or 500 MHz channel spacing.
-
Product
Machine Vision Camera - 2.3 MP, 48 FPS, Sony IMX174, Color
Grasshopper3 GigE
-
The Grasshopper®3 GigE camera family utilizes primarily Sony CCD sensors and the Sony Pregius IMX174 sensor. For FLIR GigE cameras with the latest sensors and most advanced feature sets, please refer to our Blackfly S and Oryx camera families.
-
Product
Reverse Engineering Services
-
The term “reverse engineering” can be a little confusing. It is sometimes used for things like software and electronic circuits. When 3D scanning companies use the term, they are referring to the process of re-creating design drawings by taking measurements and/or scans of the part itself. It is a 2-step process: 1) capture a 3D scan of the object, and 2) Create a 3D CAD model of the object
-
Product
COM Express Type 7 Starter Kit
COMe Type 7 Ice Lake-D STKit
-
The Type 7 Starter Kit Plus consists of a COM Express Type 7 module with ATX size Type 7 reference carrier board that offers one PCI Express x16 slot with proprietary pinout for 10GbE adapter card that convert 10GBase-KR to 10GbE Optical Fiber or 10GbE Copper signal, one PCI Express x16 slot, two PCI Express x8 slots, Serial ATA, USB3.0/2.0, Gigabit LAN and Super I/O. in addition, a IPMI BMC (miniBMC) located on carrier board connect to COM Express Type7 module by NC-SI interface to support some of out-of-band management features. All necessary cables are included.
-
Product
3U OpenVPX High Density Multifunction I/O Board
68CB6
Multifunction I/O
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
Product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
-
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
Board Cameras
-
e-CAM & See3CAM Series of Camera Boards. e-CAM camera board is e-con's reference design featuring a board camera interfaced to a processor on its high speed CMOS interface. Board cameras are available for Jetson Developer kits and NXP i.MX6 boards. For processors, that don't have the Camera ISP pipeline, e-con Systems provides the complete software stack for raw image sensors. The software stack has a wide variety of features ranging from color correction, gamma correction, dead pixel correction, color space conversion, sharpen filter etc.
-
Product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
Carrier Board
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
4-Channel DAQ Module
FMC176
-
Sundance Multiprocessor Technology Ltd.
The FMC176 is a quad channel ADC and dual channel DAC FMC. This daughter card provides four 14-bit A/D channels at 250Msps and two 14-bit D/A channels at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC176 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
Digitizer
742 Family
-
The 742 is the Switched Capacitor Digitizer family, based on the DRS4 chip by PSI, with the highest sampling frequency (5GS/s) and channel density. It can record very fast signals from scintillators coupled to PMTs, Silicon Photomultipliers, APD, Diamond detectors and others, and save them with high efficiency and precision for advanced timing analysis. The 742 family has an additional channel (two channels in case of VME boards) which can be used as time reference for time of fight measurements. The resolution of this kind of measurements can reach up to 50 ps.
-
Product
Programmable Voltage Reference Plug-In
ProDAQ 3202
-
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
Product
Cable Fault Locator-TDR
TM800N
-
TM800N Cable Fault Locator (hereinafter to be referred as TM800N) is used for test est cable break, short circuit faults of telephone cable, data cable, high frequency cable, coaxial cable,and so on.
-
Product
Time Interval Shaper
CH7-316
-
The Ch7-316 time interval shaper is designed to generate pulse sequences coherent with the reference signal (internal or external) with a wide range of repetition periods, as well as two pulse sequences with a period of 1 second (time scales) with a programmable phase shift.
-
Product
ExciPro Femtosecond Transient Absorption Pump-Probe Spectrometer
ExciPro
-
ExciPro is the first on the market femtosecond transient absorption pump-probe spectrometer. Two linear image sensors are placed in the focal in the focal plane of an imaging spectrograph to measure probe and reference spectra originating from femtosecond white light continuum generator.
-
Product
Ultra-Low Noise, Precision Voltage Reference
ISL21090
-
The ISL21090 is an ultra-low noise, high DC accuracy precision voltage reference with a wide input voltage range. The ISL21090 uses Renesas' advanced bipolar technology to achieve sub 1.0µVP-P (1.25V option) 0.1Hz to 10Hz noise with an initial voltage accuracy of 0.02% (2.5V option).
-
Product
Surge Generator
SGTEL-168
-
The SGTEL-168 is a versatile surge generator designed to simulate all the environmental surge transients as described in FCC TIA-968-B (formerly known as Part 68) and Industry Canada CS03 standard. It provides a single box solution Type A, Type B (metallic and longitudinal) and Powerline surges. These surges simulate the effect of lightning on telecom equipment under test. So it is also referred to as Lightning Simulator. The electromagnetic energy from the lightning couples into the equipment by powerline or telecom cable exposed to the lightning directly or indirectly. This model is an upgraded version of SG-168 with windows software control and a user friendly front panel for manual operation.
-
Product
Decoders
LokSound
-
Electronic Solutions ULM GmbH & Co. KG
With the LokSound family decoders we offer all model railroaders who want the utmost of authenticity on their layout, a real highlight. With LokSound , the excellent features of ESU-decoders are even more enhanced by the addition of sound functions. Its sounds simple, but “wow”: In the future, your locos not only run like the prototype, they sound exactly like it! That’s made possible through our award-winning LokSound technology- the reference for good sound on the layout since its introduction in 1999. By the inventor. By ESU. LokSound decoders are available for various applications, depending on gauge or digital system.
-
Product
Crossed-Roller Bearing Linear Stage ,13mm Travel XY,Sensitivity 1um
NFP-2461
-
Model: NFP-2461 Crossed-Roller Bearing Linear Stage ,13mm Travel XY,Sensitivity 1um Details&Spec: Please refer to NFP-1461 Specification,It is combinated by 2pcs NFP-1461(C,SR,SL
-
Product
Collimators
-
Collimators are optical systems used to imitate standard targets placed in "optical infinity" (very long distance). The collimators are used for projection of image of reference targets into direction of tested imagers. According to type of optical elements used in design, collimators are divided into two groups: reflective collimators and refractive collimators. Reflective collimators due to their wide spectral range are almost exclusively used in systems for testing thermal imagers and are also preferable in systems testing TV cameras, SWIR imagers, laser systems or multi-sensor surveillance systems. Refractive collimators are mostly used in systems for testing night vision devices or TV cameras working in visible/near infrared range.
-
Product
Potentiostat
EA163
-
This modular potentiostat is perfect for cyclic voltammetry and electroanalytical chemistry, and can use two (working and counter), or three (working, auxiliary and reference) electrodes. It can also operate as a galvanostat, ZRA (zero resistance ammeter), and high impedance voltmeter. It must be used together with any e-corder model.
-
Product
Platforms
-
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
Product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
-
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
Product
20 Bit Dual-Channel Reference Source
DRS20
-
The DRS20 is a dual-channel reference source offering ultra high precision and stability and provides a +/-10 V output. The output current can be up to 10 mA and the 4 wire connection provides a 1 µV/mA load regulation. The high precision and stability is achieved by using a temperature controlled voltage reference.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 57760
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Rheology
-
Rheology is the study of flow and deformation of materials. Deformation and flow are referred to as strain or strain rate, respectively, and indicate the distance over which a body moves under the influence of an external force, or stress. For this reason, rheology is also considered to be the study of stress-strain relationships in materials.
-
Product
Sonin Moisture Test Meter
50211
-
The Sonin Moisture Test Meter offers additional features & performance beyond those of the Moisture Test Tool. The meter’s contact probes are at the end of 3 foot coiled cable for detecting moisture in difficult to reach locations. Scale & reference chart correlate relative and moisture percentage readings
-
Product
2 Channels, 28-115 Vrms, 47 Hz-2.5 kHz (max. range) programmable
AC3
-
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
