References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SFF
Model 6353
-
- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
High Performance Embedded Development Kit
TySOM EDK
-
The TySOM™ Embedded Development Kit is for the embedded designers who need a high-performance RTL simulator/debugger for their embedded applications such as IoT, Automotive, Factory automation, UAV and Robotics. The kit includes Riviera-PRO™ Advanced Verification Platform and a TySOM development/prototyping board. TySOM boards come with either a Zynq 7000 chip (FPGA + Dual ARM® Cortex™-A9) or with a Zynq® UltraScale+™ MPSoC device. These boards include memories, and various communication and multimedia interfaces in addition to FMC connectors for peripheral expansion. Reference designs for application such as IoT, ADAS, 4K UltraHD imaging and Robotics and a complete reference design, which contains the SW (Linux) and all the hardware blocks required to support the peripherals on the board, are provided.
-
Product
Advanced PC/104 Timing Board
PC104-Plus SyncClock32
-
The PC/104Plus SG from Brandywine Communications provides precision time with zero latency to the host computer over the PCI bus. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or HaveQuick.
-
Product
Optical Wavelength Meter
-
Optoplex Optical wavelength meter (OWM) uses proprietary thin-film interference filter in conjunction with Fabry-Perot cavity technology combined with a micro-actuator and high-speed electronics. Its working principle is schematically shown below. By comparison with Optical channel monitor / Optical performance monitor, the proprietary wavelength reference unit is introduced to ensure high precision wavelength measurements. Optoplex Optical wavelength meter is the only DWDM wavelength meter capable of measuring wavelengths of multi-lasers in DWDM networks over C-band and L-band wavelength range with a high accuracy better than that the wavelength locker can provide. For example, the device can simultaneously report 80 wavelength values of 80 channels at 50 GHz channel spacing with the wavelength accuracy ± 2 GHz. DPRAM, RS-232, or USB interfaces are available and OWM can be customized to meet specific requirements.
-
Product
1500V Multifunction I-V Curve Tracer
SOLAR I-Ve
-
SOLAR I-Ve allows both testing a single-phase (three-phase with optional MPP300) photovoltaic system and verifying I-V curve. Thanks to remote unit SOLAR02, it is possible to test the system complying with the requirement of simultaneity as provided for by the reference standard. SOLAR02 is a datalogger which, synchronized with SOLAR I-Ve, acquires the data relevant to irradiation and temperature while tests carried out by SOLAR I-Ve are carried out.
-
Product
Multi-Potentiostat
1000C
-
The model 1000B series is a computerized 8 channel potentiostat. The system contains a digital function generator, multiplexed data acquisition circuitry, and a multi-potentiostat that can work with eight independent cells or eight working electrodes in the same solution with common reference and counter electrodes. The potential control range is 10 V for all channels, which can be set at independent potentials or the same potential as the primary channel, so that they can sweep or step potentials together with the primary channel.
-
Product
eVe LIDAR
-
eVe LIDAR aims to provide the ESA-Aeolus mission with a flexible, mobile reference ground-based LIDAR system capable of providing well-characterized fiducial reference measurements of aerosol optical properties
-
Product
Universal Clock
DXD-8
-
The DXD-8 Universal Clock, a precision multiformat reference generator generates up to 4 independent video syncs and audio clocks simultaneously. With the PTP option, it acts as a bridge between an IP infrastructure and legacy A/V equipment.
-
Product
Synchro Power Amplifiers
SPB
-
Computer Conversions Corporation
SPB Series: 25VA, 30VA and 100VA Reference Powered Wide-Band 60/400Hz. Models
-
Product
Instrumentation Calibration Services
-
We offer a range of instrumentation calibration services for Kemo products in addition to other signal conditioning and sensors. We have many decades of experience in the manufacture, test and calibration of our instruments and those of our competitors. Please refer to the list below for an example of our calibration options, all equipment used within our calibration department is calibrated and traceable to a UKAS accredited National standard:
-
Product
FPGA Mezzanine Card
FMC176
-
The FMC176 is a quad channel ADC and dual channel DAC FMC. This daughter card provides four 14-bit A/D channels at 250Msps and two 14-bit D/A channels at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - XMC
Model 71760
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Advanced reconfigurability features- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Remote Spectrum Analyzers
LPT-3000RX4
-
Latest DSP Technology; 9 kHz to 3 GHz Frequency Range; External 10 MHz Reference; 17 RBW filters Down to 1 Hz; 17 VBW filters Down to 1 Hz; > 88 dBm Dynamic Range; High Definition Spectrum Trace; 55 dBm Input Port Isolation; 50 dBm input attenuator; 0.5 millisecond Port Switch Speed; Available in 4, 8 or 16 RF inputs; Optional Internal Carrier Identification CID module; Optional Internal Down Converter modules
-
Product
CrystalControl
-
AMETEK Sensors, Test & Calibration
CrystalControl is a software program used to customize, update, and calibrate the nVision Reference Recorder, HPC50 Series Pressure Calibrator, and the HPC40 Series Pressure Calibrator. In addition to providing an easy way to customize your nVision Reference Recorder, it also provides a way to store and archive your recorded data runs.
-
Product
Pinhole & Porosity
-
Premature corrosion of a substrate is usually due to a coating failure. A major cause is the presence of flaws in the finished coating. Collectively referred to as porosity, the main types of flaws are:
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
Power Meters andCalibration Cells
-
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
Product
Spectrum Analyzer
-
The four traces used different windowing and averaging options. They were saved to Juxt Array memory and displayed with no added offset or spacing, to allow direct comparison. The selected trace in the array is shown with full brightness, to indicate that the cursor readouts and labeled Fields refer to this trace only. The other traces have been dimmed with the highlight control. The Juxt Trace Label Field has been set to show the contents of the Field labeled "Average", which is "32TC" for the selected trace.
-
Product
Spectrum Analysis, Up To 13.5 GHz
S930901B
-
The S930901B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 13.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Optical Power Meter
HOPM-3211
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HOPM-3211 optical power meter is a handheld optical power meter, newly released in 2007, which can be used for absolute optical power measurements as well as for relative loss measurements in optic fiber networks. An Ø1.0mm photosensitive area photodiode is used to significantly improve the stability and the reliability. It features ingenious appearance, wide range of power measurement, high accuracy, user self-calibration function and reference power level storage.
-
Product
Vector And Scalar Mixer / Converter Measurements
S95083B
-
The Keysight S95083B measurement software includes the scalar mixer / converter plus phase (SMC+Phase) measurement class. It provides fully calibrated conversion gain / loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers. Eliminating the calibration mixer requires a U9391C / F / G comb generator and an external DC power supply. A vector mixer characterization (VMC) is also included for measuring group delay of frequency-converting devices. VMC can be used to characterize a user-supplied calibration mixer.
-
Product
JadeFX FlexorSet 2-Ch. 3.0 GHz A/D, 2-Ch. 2.8 GHz D/A - 3U VPX
Model 5983-320
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex UltraScale FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two 3.0 GHz*A/Ds- Two 2.8 GHz* D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and synchronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Xilinx Sublicense FAQs - Pentek Sublicensing Agreement for Xilinx JESD204 IP Cores- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Female, 0.5m
40-971B-200D-0.5m-MF
-
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
Product
Crossed-Roller Bearing Linear Stage ,13mm Travel XYZ,Sensitivity 1um
NFP-3461
-
odel:NFP-3461 Crossed-Roller Bearing Linear Stage ,13mm Travel XYZ,Sensitivity 1umDetails&Spec: Please refer to NFP-1461 Specification,It is combinated by2pcs NFP-1461(C,SR,SL) and 1pc NFP-1461CZ(as vertical stage)
-
Product
10 Micron Wire Grid Polarizer
-
Fabricated from 10 micron diameter tungsten wire, and with a choice of wire spacing starting from 25 microns, these wire grid polarizers are suitable for use from approximately 100 microns (or 3 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
Product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
-
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
Product
Reference Electrode Kit
SC-4
-
The Model SC-4 Sliver-Silver/Chloride kit come complete with everything necessary to conduct field tests both ON SHORE and OFF SHORE.
-
Product
COM Express Type 2 Starter Kit
-
The Starter Kit consists of a COM Express Type 2 core module with ATX size reference carrier board that offers one PCI Express graphics slot x16 , four PCI Express x1 slot, two PCI slots, Serial ATA, SDVO, VGA, LVDS, TV-out, USB 2,0, Gigabit LAN, and Super I/O. All necessary cables are included.
-
Product
Package Testing
-
Lansmont package testing equipment is designed to perform industry standards, such as ASTM, ISTA, ISO, EUMOS and others. Our equipment is compliant with all of the most common ASTM and ISTA package testing procedures. There are individual standards that specifically reference how to perform drop testing, compression testing, side impact testing and vibration testing. In addition to those standards, there are groups of procedures referred to as distribution simulation tests, which incorporate some strategic combination of testing inputs, with the idea of simulating a typical journey through the supply chain. Some of the most common distribution simulation standards that are performed globally are published by ASTM and ISTA.
-
Product
Data Acquisition
-
Sound, vibration, status and reference variables, voice, audio data and more: HEAD acoustics is setting the standard in data acquisition. We offer flexible systems for mobile applications and operation in the laboratory. Our data acquisition systems can also be expanded flexibly using various software and hardware modules.
