Data Test Sets
-
Product
Data Logging Software
DPM-3DLS
-
Turns a PC connected to up to 31 DPM-3 instruments into a powerful, low-cost data logging system.
-
Product
Structural Testing
-
Structural testing is used to verify the static strength, or fatigue strength, of a component by applying measured loads. Testing can be done to failure, to contractual requirements, or to validate finite element model predictions.
-
Product
In-Circuit Testing and Test Engineering
Teradyne Z1820
-
2048 Pure Pin Test Nodes3 & 6-wire Analog MeasurementsVector Test for VLSI, PLCC’s & ASICSMultiscan II Vectorless TestingIEEE Functional Interface BoardLarge Custom Vector Library
-
Product
EIA Test Charts
-
EIA Test Charts by Applied Image - EIA Halftone Gray Scale Chart, EIA Video Resolution Pattern
-
Product
Fiber Optic Talk Sets
-
These fiber optic talk sets use spare fibers from a fiber optic cable so can techs to communicate. Talk Sets are an economical way for voice communication when testing single-mode or multi-mode cable. They will not be affected by distance. A technician needs to know that they can communicate no matter where they are working. A cell phone cannot always do the job. The location of the fiber optic network installation may hamper the phone signal. Whether it is a new installation, maintenance or testing, they will provide outstanding performance you need as an installer.
-
Product
Thermocouple Alarm Setting Transmitter
Model TAT
-
Kusam Electrical Industries Limited
• 4 Digits Display For Input Signal:0 - 9999 • Output Signals Are Programmable. • Ultra-thin Dimension, 27mm width. • Non-Combustible PC Case .DIN Rail or Wall Mounting. • High Dielectric Strength ( AC 2KV / Min , Input / Output / Power )
-
Product
Automotive EMC Testing
-
Having been assessed by Ford Detroit’s EMC expert, we are Australia’s only Ford (and NATA) accredited automotive EMC test laboratory. Others have tried, but none have succeeded. Ford does not accept reports from EMC labs that are not on the Ford list of accredited labs. The scope ranges from component to complete vehicle level EMC testing for Australian and overseas manufacturers. We also have a fully dedicated CISPR 25 Electronic Sub Assembly (ESA) chamber, another large CISPR 25 anechoic chamber for vehicle testing or susceptibility levels in excess of 500V/m. We possess a vast array of specific automotive EMC test equipment such as BCI’s, tri-plate’s, and striplines for susceptibility and emissions testing to meet the most stringent automotive EMC requirements. Our Australian and overseas customers use our labs because they know that our reports will be accepted and will not be questioned.
-
Product
Test Automation Systems
iTest
-
Our iTest family of test automation systems provide a full range of capabilities, allowing you to purchase just the right solution for your application without having to overbuy.
-
Product
Data Acquisition Switch System
M300
-
No matter the product performance test in the R & D stage or the automatic test in the production process, for the application of multiple test points and multiple signal measurement, the M300 series data acquisition / switch system with modular structure combines the precise measurement function with the flexible signal connection function, and can provide a wealth of test measurement solutions.
-
Product
Temperature Data Acquisition
THERMES-USB
-
Physitemp’s Thermes high accuracy data acquisition system has been redesigned to create a more versatile USB model. The new system requires no internal connections to your computer and simply connects via an external USB port on your laptop or desktop computer. Two versions of the data acquisition system are available. The standard version, THERMES USB, is connected to your computer USB port. The wireless version - THERMES USB WFI, can be either directly connected to a USB port or, with the included wireless receiver, positioned up to 100 feet from the host computer. Each unit will accommodate up to 7 type T thermocouple sensors and multiple Thermes units may be connected to the same computer for more thermocouple inputs. A high accuracy electronic cold junction compensation circuit maintains typical system accuracy of ±0.2°C over an ambient temperature range of 15 to 35°C. Individual offsets may be added to each input in software to facilitate individual calibration of each channel. (see THERMES-USB WFI)
-
Product
Test Container
MTL 15 | VP 700006
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MTL 15 test container works completely independently thanks to the optionally available, fully integrated power generator. Equipped with a hydraulic set-down device including cable remote control, the test system can be set up within 15 minutes and is therefore ideal for changing locations.
-
Product
Single Sheet Testing
-
Incoming material inspection can be very useful where strict quality standards are maintained. It saves a lot of processing cost since lossy material is inspected at the entry level before it goes to production level. Epstein Stack testing is one of the oldest and widely used method for electrical sheet testing.
-
Product
Vehicle Test Laboratory
-
As an industry-leading partner, Trialon provides the expertise, experience, and equipment to develop vehicle and portable powertrain test carts that serve as “rolling laboratories” for the Powertrain EMS development team. Trialon provides test trip support and development support at customer sites.
-
Product
Test System Elowerk
eloZ1
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the latest generation. It reliably finds connection errors and assembly errors in electronic assemblies. The test electronics can be integrated both in table systems and in inline systems.
-
Product
Building Materials Testing
-
Through Stanger Testing Services Limited a wide range of services are available to the construction industry, including standard cement tests, the assessment of aggregates and cladding stone, the valuation of admixtures and the determination of the mechanical properties of most building materials.
-
Product
Pre-compliance Testing
-
SILENT offers pre-compliance testing for products with planned distribution to commercial and industrial markets in the US and overseas. This includes testing to ensure that emissions, immunity, and circuit-to-circuit interference problems are discovered early and immediately brought under control. We use the most advanced EMC and RF test & measurement equipment and diagnostic software available from leading suppliers.
-
Product
Manual Test Stand
-
Test conditions have a major influence on the quality of force measurements. Using the right support for your force gauge will ensure repeatable, precise and accurate results.
-
Product
Optics Test Systems
Electronic And Visual Autocollimators
-
Optik Elektronik Gerätetechnik GmbH
OEG GmbH specializes in the use of autocollimators, collimators and telescopes for special applications in optical measurement technology in the wavelength range from 380nm to 1550nm (SWIR).
-
-
Product
Pre-compliance Testing
-
Save your company valuable time and money by involving Nemko early in the product development process.
-
Product
Strain and Fatigue Testing
-
ATA engineers have developed the skills and tools necessary to solve intricate and complex strength and fatigue problems.
-
Product
Material Testing
-
A respected and established technique that is used to ascertain both the physical and mechanical properties of raw materials and components.
-
-
Product
Cleanliness Test Systems
CM Series
-
The Contaminometer (CM Series) test systems were originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s.
-
Product
Network Testing Software
-
Get the most out of your PCTEL® scanning receivers with SeeHawk® Touch and Collect network testing software and the SeeHawk™ Central cloud reporting and automation platform. Our intuitive interface makes it easy to conduct drive testing, walk testing, troubleshooting, commissioning, and reporting for cellular, WiFi, and critical communications networks indoors and out. With SeeHawk Central, you’ll also get instant online data access, workflow automation, and report sharing tools for grid-based in-building testing.
-
Product
Quality Assurance Testing
-
Manufacturers rely on Quality Assurance (QA) testing to maximize customer satisfaction and minimize costly after-sales troubleshooting and support. One of the best known drivers behind QA testing is the ISO 9000 standard, but there are many others.
-
Product
Digital Test Hammers
-
James Instruments? digital test hammers are an advanced, completely automated system for estimating concrete compressive strength. Its calculation, memory and recording functions allow for quick, easy and accurate test results.
-
Product
Motor Test Port
MTAP2
-
We know safety is number one priority in any motor reliability program that is why PdMA developed the MTAP2, our answer to safe electric motor testing. With the combination of MCEMAX® or EMAX, the MTAP2 makes testing easier, faster and above all safe!
-
Product
Environmental Testing
-
DATASYST Engineering & Testing Services, Inc.
Simulate real-world environmental conditions to know how your product or component measures up. DATASYST evaluates how your product responds to environmental stressors, including temperature, thermal shock, humidity and altitude.
-
Product
Textile Testing Instruments
-
Dongguan Amade Instruments Technology Co., Ltd
Textile testing instruments are developed to determine the quality and performance of various fibrillar component fabrics, structural fabrics, garments, home textiles and other textiles by physical and chemical methods in conformance with international standards. By using scientific testing methods to judge the quality of materials or final products, manufacturers of textiles are capable of detecting the defects and unqualified products to correct problems in time, conducive to reducing loss and maintaining the business reputation. Testings cover tensile strength, tearing strength, seam slippage, joint strength, bursting strength, resistance to wear, pilling resistance, color fastness to washing, rubbing fastness, light fastness, color fastness to perspiration, dimension stability, inflaming retarding test etc.
