Data Test Sets
-
Product
Laboratory Air Data Test Sets
-
DMA is a leading manufacturer of Air Data Test Set models for laboratory use achieving the highest accuracy and resolution. The MPS46 is digitally controlled through a keyboard, it uses very high accuracy pressure sensors, with a special characterisation for maximum accuracy (for static channel < 2 feet at sea level). Pressure resolution of 0.2 Pa. is also achievable. The intuitive user interface with touchscreen display ensures that all the functions are controlled with a minimum of key presses . The ADTS can be used in avionics ATE systems (rack height only 2U) for automated pitot-static testing through RS232, USB, Ethernet or GPIB/IEEE488. An internal pump or external rack mounted pump unit can be supplied as an option.
-
Product
Air Data Test Sets
-
For calibrating altimeters, airspeed indicators, rate-of-climbindicators and other avionic instruments.
-
Product
Air Data Calibration
-
Fluke calibration offers digital pressure monitors, air data calibrators and laboratory standards for air data pressure range calibrations. Each of these systems feature pressure ranges, measurement units and features specific to calibrate air data test sets and RVSM compliant air data instruments. Models include 2468 Ruska and ADCS-601 DHI primary level standards; 7750i Ruska air data controller/calibrator and RPM4-AD DHI reference pressure monitor.
-
Product
Air Data Test Set System
B511
-
The BRAT Option B511 is an option to the BRAT Test System utilizing Commercial-Off-The-Shelf (COTS) equipment. The system is used to augment the existing BRAT capabilities to test rate of change of altitude or pressure.
-
Product
Air Data
-
Testing altitude and airspeed components in commercial and military air data applications are critical for the safety and performance of an aircraft. Mensor air data test set and indicators provide the high accuracy necessary for these applications. Air Data Test Sets control altitude /altitude rate and airspeed /airspeed rate, for testing altimeters and airspeed indicators or air data computers in a dynamic way that simulates actual flying conditions. Air data Indicators measure Altitude /Altitude Rate and Airspeed /Airspeed Rate for applications where conditions are externally controlled.
-
Product
PXIe-8267, 4 TB, M.2, PXI Data Storage Module
785308-01
Data Storage
PXIe, 4 TB, M.2, PXI Data Storage Module - The PXIe-8267 PXI Express high-speed data storage module features large-capacity, high-throughput storage in a single PXI Express slot. With M.2 solid-state drives, the PXIe-8267 is ideal for stream-to-disk or stream-from-disk applications requiring sustained, reliable data throughput such as high-speed signal intelligence, RF record and playback, and multi-sensor data acquisitions systems.
-
Product
Automotive Test Solutions
test
The testing and simulation systems from this division are used primarily in the automotive and automotive supplier industry. These are, for example, modular function-testing systems and diagnostic tools for automotive ECUs or bus communication systems for a wide variety of electronic components in automotive production. Electromechanical assemblies and entire car seats are also tested to ensure they function
-
-
Product
Standardize Production Test Software For PCBAs And Electronic Devices
test
The vast majority of test project man-hours are spent on software development, so the choices that teams make in software tools and architecture have significant impact on deployment schedules. Standardizing software across a team or organization increases both efficiency and proficiency, lowering the risk of missed deadlines and improving test quality and reliability. Test software must:
-
Product
Semiconductors Testing
test
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
Product
3 Function Slot MOSA Nano Data Concentrator Unit (DCU)
NIU3A-DCU-01
Data Concentrator Unit
NIU3A-RDC-01 is a Modular Open Systems Approach (MOSA) Data Concentrator with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
Product
Automated Test Equipment
test
These systems test semiconductor performance and quality with industry-leading precision and cost efficiency. Robust support for semiconductor design evaluation, volume production ramps, and yield improvement.
-
Product
Cable Free ATE
CABLEFREEATE
test
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
PXI Data Acquisition
DAQ
Data Acquisition Module
Installation and configuration is fast and easy with standard connectors, soft front panels and Keysight connection expert. In addition, software drivers support the most common programming environments such as Visual Studio®, C, C++, Visual Basic, MATLAB® and LabVIEW™.
-
Product
Dual Function Slot MOSA Nano Remote Data Concentrator Unit (RDC)
NIU2A-RDC-01
Data Concentrator Unit
NIU2A-RDC-01 is a Modular Open Systems Approach (MOSA) Remote Data Concentrator with low power high performance ARM Cortex -A9 processing. 512 MB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet and optional Fiber Optic Ethernet support.
-
Product
6U High Performance Data Acquisition subsystem
CPCI-AD320
Data Acquisition Module
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8320-6U can also accept external scan and trigger signals from a front panel connector.
-
Product
16-CH 16-Bit 250 KS/s Simultaneous Sampling DAQ Cards
PXI-2022
Data Acquisition Module
ADLINK"s PXI-2022 is a simultaneous-sampling multi-function DAQ card to meet a wide range of application requirements for PXI bus computers. The device can simultaneously sample 16 AI channels with differential input configurations in order to achieve maximum noise elimination.
-
Product
8-CH Thermocouple Input Module
ND-6018
Data Acquisition Module
- Channels: 6 Differential & 2 Single-ended- Input Type: Thermocouple, mV, V and mA- Thermocouple Type: J, K, T, E, R, S, B, N,C- Voltage Range: ± 15 mV, ± 50 mV, ± 100 mV, ± 500 mV, ± 1 V, ± 2.5 V- Current Range: ± 20 mA- Isolation Voltage: 2500 VRMS
-
Product
Automatic Test System
Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
6TL29 Semi-Automated Test Platform
AQ377
Test Platform
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
Product
Automated Compliance and Device Characterization Tests
N5990A
Test Platform
The Keysight N5990A test automation software platform is the most powerful tool for serial and multi-lane gigabit testing. It is the unique universal platform for testing a wide range of digital buses such as PCI Express, USB, HDMI or MIPI. The same graphical user interface and operating principles are used for all applications. This boosts productivity, especially when testing devices which support multiple digital buses. The N5990A can be tailored to your individual test needs with the flexible test sequenzer and controls all instruments needed for your tests. The configurable database interface of the N5990A test automation platform enables the convenient storage of all test results. A web interface allows an effective and easy operation. Custom calibration and test procedures can be implemented easily with User Programming.
-
Product
High Temperature Component Test Fixture
16194A
Test Fixture
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
Data Acquisition Module
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
Product
Component Test Systems
Test System
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
Product
VXI Digital Multiplier
4152A
Test System
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional Test
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
