SD Card
A non-volatile memory card format.
-
product
Dual-Port Serial Interface Cards
PCI-COM2S And PCI-422/485-2
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
-
product
RS232/422 Strobe Mux III Card & Panel
9565-32
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25 mm).
-
product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
CMOSS PNT Card
CPNT
CPNT fuses GNSS, inertial measurement, and high-performance timing oscillators with GNSS jamming and spoofing detection and CRPA/AJAS antenna compatibility in a flexible, configurable device to provide PNT assurance in threat-filled environments.
-
product
FPGA Mezzanine Card
FMC172
The Abaco FMC172 wideband low latency FMC module is based on the latest high performance ADC device from Texas Instruments and DAC devices from Teledyne-E2V. It is the fastest ADC Abaco offers with LVDS interfaces, delivering up to 6.4 GSPS ADC on a single channel (or two channels @ 3.2 GSPS) and a single channel DAC at up to 6.0 GSPS, making it among the fastest low-latency devices available on the market. The combination of the FMC172's >6.0 GHz bandwidth, its high sample rate and low latency is ideal for advanced Digital RF Memory (DRFM) systems.
-
product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 773kΩ
50-297-143
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI 8x9 RF Coaxial Matrix Card 50Ω SMB
50-725A-511
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
product
PC/104+ Card with 4 IP Slots
PC104p4IP
If you want to use IndustryPack modules with your PC/104+ or PC/104-Plus system, the PC104p4IP is the choice for you. The PC104p4IP combines features you need with simplicity and speed. Up to 4 IP modules can be installed. Standard 16 bit IPs plus 32 bit, and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection. The PC104p4IP is highly integrated with the PCI and IP interfaces closely coupled within the same FPGA.
-
product
Osprey Probe Card
The Osprey probe card is MPI’s solution to demand for ever finer pitch. It is designed for smaller Al pad, and is ideal for tiny pitch application with peripheral and full array pattern. With precise alignment and better planarity control, Osprey can reach higher productivity by multi-DUT design. The forming wire (FW) type needle produced with MPI’s own micro fabrication process not only delivers high-quality performance but also allows easy needle replacement and shortens maintaining cycle time.
-
product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, LAN, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s) And 2 PCIe Mini Card Slots
IRU152
The IRU152 is powered by the low-power NXP i.MX 6 UltraLite processer. It can withstand an extended operating temperature range of -40°C to +70°C and up to 2G of vibration for operating in harsh environments. Furthermore, it supports NI LabVIEW to allow users to design graphical user interfaces for their measurement applications quickly and efficiently. In order to provide data collection and device control, the IRU152 comes with various I/O connectors, including four analog input (AI) channels, one isolated RS-232/422/485 port, one isolated LAN and one isolated DIO (2-in/2-out). The four analog input channels have differential input configuration and overvoltage protection of 55V DC. The maximum sampling rate of IRU152 is up to 250 kS/s with a 16-bit resolution for low-speed high-resolution sensor monitoring and signal measurements. Apart from the abovementioned features, the IRU152 comes in two PCI Express Mini Card slots and one SIM card slot for Wi-Fi, 3G/4G and LoRa connections. The DIN-rail embedded system is equipped with onboard 512MB DDR3 SDRAM; besides, they have an 8GB eMMC flash memory. The extremely low power industrial IoT gateway has passed the Heavy Industrial certification and FCC part 15 to ensure the excellent quality and highly reliable performance.
-
product
Fanless Embedded System With Intel® Celeron® Processor N3160, VGA, HDMI, 4 COM, 2 GbE LAN, 4 USB, And 2 PCI Express Mini Card Slots
eBOX625-853-FL
The eBOX625-853-FL is powered by the latest Intel® Celeron® processor quad-core N3160 (formally codename: Braswell) with one DDR3L-1333/1600 SO-DIMM socket with up to 8 GB memory. The reliable Intel® Celeron® N3160-based embedded box computer supports Intel® Virtualization Technology (Intel® VT-x) which maximizes flexibility and enhances security and efficiency. The eBOX625-853-FL is ideal for IIoT (Industrial Internet of Things), retail equipment, Multi-Media Kiosk, industrial gateway, automation, and many more.
-
product
Isolated Serial Communication Card
PCI-ICM-1S
The PCI-ICM-1S is a single port asynchronous optically isolated serial communication card that can be installed in any 3.3V or 5V PCI slot computer. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
product
RS-422/485 Serial Communication Card
LPCI-COM-1S
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
product
PXI 8-Slot BRIC 48X8 Matrix, 2A 2-Pole (2 sub cards)
40-565A-102-48X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI 8-Slot BRIC 96x8 Matrix, 2A 2-Pole (4 sub cards)
40-565A-102-96X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
In-Service Electrical Continuity Test Card
Cisco ONS 15454
The Cisco ONS 15454 In-service Electrical Continuity Test Card is a solution for confirming proper DS-1 and DS-3/EC-1 cabling between the Cisco ONS 15454 shelf assembly electrical interface adapter (EIA) panels and the user's patch panels. The solution is designed for shelf installations that are presently carrying traffic and tests for common wiring errors including electrical shorts, opens, wrong connections, and tip/ring reversals.
-
product
ATX Motherboard With LGA1151 Socket 8th Gen Intel® Core™, Xeon® E Processor, Intel® C246, USB 3.1 Gen2, SATA 3.0, PCI Express Mini Card Slot, VGA, DisplayPort, DVI-D, And HDMI
IMB525
*LGA1151 socket 8th gen Intel® Core™ i7/i5/i3, Xeon® E, *Pentium® or Celeron® processor (Coffee Lake)*Four 288-pin DDR4-2666/2400 ECC DIMM for up to 64GB of memory*DisplayPort, DVI-D, HDMI and VGA with triple-view supported*6 SATA-600 with RAID 0/1/5/10*1 PCI Express Mini Card slot (optional)*2 USB 3.1 Gen2 and four USB 3.1 Gen1*TPM 2.0 supported (optional)
-
product
Low-Cost 16-Bit Multi-Function DAQ Card with 2-CH Encoder Input
PCI-9221
The ADLINK PCI-9221 is a 16-bit high-resolution and low-cost multi-function DAQ card, with 16-CH singleended or 8-CH differential input capable of up to 250 kS/s sampling rate. In addition, the PCI-9221 comes with a 2-CH 16-bit static analog output and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, general-purpose timer/counter, encoder input, and PWM output. The flexible function I/O makes the PCI-9221 the best single-board solution for combined data acquisition and simple motion control functionalities. Ideal for manufacturing, laboratory research, and factory automation, the PCI-9221 comes with all the functions you need at an affordable price.
-
product
Dual HDMI Input Expansion Card
FMC-HDMI
Sundance Multiprocessor Technology Ltd.
The FMC-HDMI extends FMC-compatible FPGA systems with two HDMI Type A input ports. It’s extremely useful for image or video processing applications. One of the ports features a fully-fledged HDMI 1.4 receiver with CEC, HDCP, audio, and 3D TV support. The other port provides cable equalization and buffering for HDMI signals, leaving the decoding up to the user.
-
product
Probe Card
VersaTile™
Celadon has reduced the size of a probe card to 28mm with the VersaTile™ with Advanced Cantilever™ technology. The VersaTile™ with Advanced Cantilever™ technology can fit on a conventional 3-hole mount probe positioner for single site probing. The same VersaTile™ with Advanced Cantilever™ technology can be used in a 300mm VersaPlate™ for multi-site probing.
-
product
PXI 4 Slot BRIC 44x16 1-Pole (4 sub cards)
40-562A-021-44X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 26.7kΩ
50-298-132
The 50-298-132 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 26.7kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Express Card With Eight Isolated Inputs, Eight Relay Outputs, And Change Of State Detection
PCIe-IIRO-8
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
product
PMC Card
P-DIS
The P-DIS PMC card is different from most currently available data acquisition boards. It provides multiple I/O types on a single module and the functionality to work with high-speed digital I/O signaling. With very accurate time stamping of input data and synchronization to an external IRIG-B source, the P-DIS provides the capability to precisely synchronize all output ports.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C/i(DIOi480)
The D480C/i offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
32-CH Isolated DIO PCI Cards
PCI-7230/33/34
ADLINK"s PCI-723X series are 32-CH isolated input and/or output cards which provide a 2,500 V optical isolation protection. The wide input range of the PCI-7230 and PCI-7233 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The PCI-7230 and PCI-7234 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automation applications. The PCI-7234P provides current-source output capability. The PCI-7230 and PCI-7233 also provide two interrupt sources on digital input channels. The PCI-7233 also features a change-of-state (COS) function that generates an interrupt when any digital input changes its state.
-
product
Rugged Embedded MIL-STD-1553PCI Express Mini Card
AME1553-1-E
Rugged Embedded MIL-STD-1553 PCI Express Mini Card with 1 Dual Redundant channel plus 2 discrete Input, 2 discrete Output channels.
-
product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
