SD Card
A non-volatile memory card format.
-
product
3U VPX FPGA Cards
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form.
-
product
PMC Interface Card
CPCIC-MA4
The CPCIC3/6-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
product
PCI 50xSPST Shielded Reed Relay Card
50-125-121
The 50-110/115 range of switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector. For applications requiring improved bandwidth and crosstalk performance please look at our 50-120/125 range of shielded reed relay cards.
-
product
Multi Function Relay PXI Card
GX6377
The GX6377 3U PXI multi function switch card provides users with the ability to switch both high current and general-purpose signals using only one 3U PXI switch module. The card features multiple channels of high current switching capability for 10 A and 2 A applications as well as two, 16 x 2 switch matrix groups, which can also be configured as a 32 x 2 or 16 x 4 matrix.
-
product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
14 Bit ADC Card
FMCADC100M14B4CHA
Sundance Multiprocessor Technology Ltd.
The FmcAdc100M14b4cha is a 4 channel 100MSPS 14 bit ADC card in FMC (FPGA Mezzanine Card) format. By default it uses only signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5V, +/-5V. An advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range of +/- 5V that is independent on the chosen gain range.
-
product
PCI Precision Resistor Card 18-Channel, 1Ω To 62.1Ω
50-297-011
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Measurement and Control Card
PCI BASEII
The PCI-BASEII is a multifunctional measurement and control card for stationary applications. Their modular design guarantees individual and flexible adaptation to a measurement application. The low latency of the PCI interface makes the card particularly attractive for control and regulation tasks.
-
product
High-Density 128-CH Isolated DIO/DI/DO PCI Cards
PCI-7442/7443/7444
Responding to the industry"s need for high-density digital input/output modules, the ADLINK PCI-7442/7443/7444 DIO card series delivers up to 128 opto-isolated channels for a wide range of demanding PCI-based applications. The PCI-7442/7443/7444 series comes with 64 (PCI-7442) or 128 (PCI-7443) opto-isolated digital inputs and 64 (PCI-7442) or 128 (PCI-7444) opto-isolated digital outputs. With a 1250 VRMS (excluding cables) channel-to-system isolation protection, these cards are shielded from damage caused by accidental contact with external voltage while promoting simple ground connections. All input channels are identical non-polarity with each line isolated and suited to collect digital inputs even at high-noise environments. Featuring a Change-of-State (COS) interrupt function, the PCI-7442/PCI-7443 instantly generates an interrupt request to the PCI controller when it detects a sharp change in the logical state of any of its digital inputs.
-
product
48-CH DIO & Timer/Counter Cards
cPCI-7248/7249R
- PICMG 2.0 Rev 2.1- 48-CH digital TTL/DTL input/output- Emulates 4/2/1 industry standard 8255 PPI (mode 0)- Direct interface with OPTO-22 compatible I/O modules Output port status read back- On board 8254 timer/counter chip
-
product
Probe Card Analyzers
PB1500
The PB1500 is a low cost probe card analyzer system. It has the capability to perform all the tests done on the larger PB3600/6500 probe card analyzers, but at a lower cost for low pincount cards. A maximum of 1,280 channels may be configured in the PB1500 MUX system. The Precision Measurement Unit (PMU) has the same accuracy, repeatability and range as the larger analyzers. The repair process consists of selecting a failing probe, which moves it under the binocular microscope and positions a crosshair over the correct position for that probe.
-
product
Mechanical Stress Card Testing
Wheels are transversely positioned with micromechanical stopsPressure exercised on the card's chip and microcircuitryThe card is free to deform in the Z axisThe stress is controlled by an accurate, precise force sensorProgrammable number of cycles
-
product
Multi-Protocol Card
EXC-4000PCI
The EXC-4000PCI/xx card for the PCI bus supports up to forty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.The receive channels allow for the storage of all selected labels with status and time tag information appended to each word, and also allow for filtering and multi-storage modes of data words.The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.
-
product
Adapter / Carrier Converter Card
PCIBPC104pET
PCIBPC104pET adapter / carrier converter card provides the ability to install 1-4 active PC104p or PCI-104 cards into a standard PCI slot. PCIBPC104pET has a PC104p and PCI-104 compatible stack position mounted to a universal voltage shorter than 1/2 length PCI card. The PC104p position is stackable with all 4 active positions usable.
-
product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
-
product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Digital I/O Card w/CoS IRQ
PCIe-DIO-24HS
This product is a x1 lane PCI Express digital I/O board available in two models. The PCIe-DIO-24H is the basic DIO and the PCI-DIO-24HS features advanced change-of-state (COS) detection capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
product
2-port/4-port GigE PCI Express Card
AX92322
The AX92322 is a GigE compliant PCI Express card supporting two or four independent Gigabit Ethernet ports. It features PCI Express x4 interface and has four powerful independent Intel® Ethernet Controller i210-AT. The GigE frame grabber card supports 9.5KB Jumbo Frame and IEEE 1588 to enable faster and more accurate throughput of data. The AX92322 is built for machine vision and surveillance applications in industrial IoT field. This PCI Express frame grabber card is designed to help customers develop and deploy machine vision and surveillance applications which will greatly benefit through reduce the cost and simplify system integration. Moreover, the AX92322 has a wide operating temperature of 0˚C to 70°C, making it suitable to be used in most server environments. The advanced GigE frame grabber runs on Windows® 7, Windows® 10 and Linux.
-
product
CompactFlash Card
PMCF3
PMCF3 is a COTS IEEE 1386.1 compliant PMC with removable CompactFlash card up to 6 GB that offers a convenient way to add large capacity, non-volatile memory to rugged system solutions. Targeted at the world's defense and aerospace OEM marketplace, this cost-effective CompactFlash adapter is ideal for use with our families of COTS SBCs and PMC carrier cards.
-
product
Non-Multiplexed High Speed Continuous Function Card Overview
This type of system can be designed with benefits of both the multiplexed amplifier-per-channel and transient recorder systems. Benefits of the non-multiplexed amplifer-per-channel system include: High Sampling Rates: With an ADC per channel, the sampling rate is not encumbered with considerations such as multiplexing and post-amplifier settling time.Superior Filtering: With an ADC per channel, digital filtering can be used to augment analog filtering to achieve better anti-aliasing performance with much lower effective sampling rates.Superior Phase Matching: Digital filtering provides much steeper, more predictable rolloff rates and phase characteristics than analog filtering with greater stability with time and temperature changes at lower cost.
-
product
64-CH, 12/16-Bit, Up to 3 MS/s Multi-Function DAQ Cards
DAQ-2200 Series
ADLINIK DAQ-2204, DAQ-2205, and DAQ-2206 are high-density and high-performance multifunction DAQ cards. The devices can sample up to 64 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 32 AI channels in order to achieve maximum noise elimination The DAQ-2200 series also feature analog and digital triggering, 2-CH 12-bit analog outputs with waveform generation capability, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm
50-294-022
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
-
product
8-CH 16-Bit PCI Express Analog Output Card
PCIe-6208
ADLINK PCIe-6208 series are 8-CH, 16-bit, PCI Express analog output cards which provide high resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
product
FPGA Mezzanine Card
FMC160
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.7Gsps (2.85Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. It is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1).
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Dual Channel 180 MS/s Digitizer PXI / PXIe Card
GX2482
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
-
product
Card Edge Connectors
R600
VECTOR Electronics and Technology, Inc.
R656-2R600 series card edge female connectors for 0.062"(1.57mm) thick boards. Available in wire-wrap or solder tail type termination.Available in 30, 72, 44, 56, 80 and 100 contacts total with dual row.
