In-Circuit Test
Testing of short circuits, open circuits, component values and operation of ICs.
See Also: In-circuit, Incircuit, In-Circuit Debuggers, In-circuit Emulators, In-circuit Probes, In-circuit Testers, In-circuit Test Systems, Combinational Testers, ICT
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
Power-off Circuit Board Testing
Huntron® Trackers®
-
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
Product
VLF test system
BAUR PHG 80 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
PCB Test Fixture Kits
-
Emergent's fixture kits are available in bottom and double sided probing versions. They are fully scalable, from compact benchtop testers to full size multi-UUT production floor models. The removable, interchangeable plate design allows you to easily add and move test points, or swap out plates to test a completely different product. Each kit comes with a standard linear collapse over-clamp. A cam-follower closing system can be specified for higher force applications. Our fixture kits are manufactured using industrial grade phenolic laminate, which is similar to G10 in hardness and strength but easier to machine. The standard kit comes pre-assembled with blank plates for machining.
-
-
Product
Testing Software
-
SMC supplies as standard several types of software adapted to each set, for automatic testing, unit operation and reports or results acquisition, which allows the full functionality of the equipment; the following programs are included with the corresponding equipment:
-
Product
Microwave/RF Cable Test Assemblies
PHASEFLEX
-
For test applications that require precise, repeatable measurements, microwave/RF test assemblies from Gore provide excellent phase and amplitude stability with flexure. Our rugged, lightweight assemblies deliver reliable performance with longer service life and reduced equipment downtime resulting in lower costs for testing in laboratory, production and field test environments.
-
Product
Kelvin Contact Test
-
C.C.P. Contact Probes Co., LTD.
We offer different tip types for low resistance testing.
-
Product
Engine Test Systems
TITAN Engine
-
The TITAN engine test system series contains fully equipped engine test stands which are designed for various categories of internal combustion engines, ranging from light-to heavy-duty engines and also offering solutions for component tests such as testing the exhaust line. Further adjustment for off-road engines, powered two-wheeler engines, small internal combustion engines from carts, snowmobiles or motorboats as well as aircraft turbines are available. Additionally, it is also possible to test alternative engine concepts.
-
Product
Primary Test Equipment
LET-2000-RD
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
Testing
-
Apogee Labs offers a wide variety of modular chassis types used for test applications with various Data Link Test Modules.
-
Product
Endurance testing machine for bed
-
This device is an endurance tester for ordinary home beds. It can also be used as a compression tester.
-
Product
Leak Testing
-
Leak testing is a non-destructive method to verify the presence of a leak in a component or device.It is implemented as a control methodology for monitoring production process and product quality control. Leak tests are used to find out possible leaks due to non-suitable material (porosity, blowholes, cracks), or in the machining process to find out machining errors or defective parts, and ultimately in assembly, to find out missing or defective gaskets, wrong positioning or assembly. The presence of a leakage could jeopardize the correct functioning of the component, device or its life span, and can also be potentially dangerous for the environment and the safety of its user.
-
Product
Online Tree Testing Software
Treejack
-
Take the guesswork out of information architecture with Treejack – the usability testing tool you can use to test your IA without visual distractions. Treejack helps you prove your site structure will work before you get into interface design. Tree testing is a usability technique for evaluating the findability of topics in a website. It’s also known as ‘reverse card sorting’ or ‘card-based classification’. Tree testing is done on a simplified text version of your site structure – without the influence of navigation aids and visual design.
-
Product
Test Automation
-
Test automation can be the solution to releasing new features and functionality with reduced time to market and uncompromising quality. There will, however, always be times when manual testing is the most appropriate approach.
-
Product
UX Usability Testing Tool
Indigo Studio
-
Your complete solution for collaborative prototyping and usability testing with video replays. Fast, code-free prototyping for today's most popular platforms. Design for mobile, web, or desktop using Indigo Studio’s built-in controls and platform environments - complete with touch and swipe gesture support. Run your prototype from any device with a web browser. Import designs from Sketch, and create reusable, interactive UI components.
-
Product
Liquid Dielectric Test Cell
LT-4123
-
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
-
Product
Testing Instruments
-
NDT testing instruments, other testing instruments, paper testing instruments, plastic testing instruments, rubber testing instruments, soil testing instruments
-
Product
Nanomechanical Test Instruments
-
Bruker has developed a comprehensive suite of nanomechanical and nanotribological test instruments that operate in conjunction with powerful microscopy techniques. Combining the advantages of advanced microscopy technologies with quantitative in-situ nanomechanical characterization enables an accelerated understanding of material behavior at the nanoscale.
-
Product
IP Waterproof Test Equipment
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s IP waterproof test equipment is divided into nine common waterproof levels according to international and national standards, namely IPX1, IPX2, IPX3, IPX4, IPX5, IPX6, IPX7, IPX8 and IPX9. In addition, there are many different comprehensive rain test chambers, whether it is the common nine instruments or customized spray chambers, charging pile water spray tests or energy storage cabinet spray tests. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
Pressure Testing
-
Types of Pressure Testing Performed at GTS:*Hydrostatic Pressure Testing*Leak Pressure Testing*Burst Pressure Testing*External Pressure Testing*Pressure Testing at Temperature Extremes*Vacuum Pressure Testing*Differential Pressure Testing*Cyclic Pressure Testing
-
Product
Software for Testing Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
We offer extensive and powerful software packages for our systems. All of our testing systems are controlled with our Hillgus testing software and the test results are stored in our open file formats. With our evaluation software Oculus, the findings can be subsequently evaluated and documented. Both Hillgus and Oculus were developed in-house and are constantly being improved. Due to the modular structure, the software can be optimized for every requirement and expanded at any time.
-
Product
Emissions Test System
PC-114
-
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
Product
5G NR Testing
-
5G NR is the first communications standard designed to support a wide variety of consumer and industry applications. 3GPP release 15 laid the foundation for 5G NR by introducing new, flexible numerology, advanced channel coding and modulation schemes. Enabling wider channel bandwidths and extended carrier aggregation schemes while also extending frequencies into the millimeterwave range make more radio resources available.
-
Product
Flame & Other Plastics Testing
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
Product
Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
Insulation is one of the most important constituents of a transformer. Any weakness in the insulation may cause failure of transformer. To ensure the effectiveness of the insulation system of a transformer, it must confirms the dielectric test. But the power frequency withstand test alone can not be adequate to demonstrate the dielectric strength of a transformer.
-
Product
Transformer Test Panel/ Setup
-
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
Product
Flying Prober Test System
QTOUCH2204C
-
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.
-
Product
Test Bench
PHIL
-
Universities around the world are rapidly adopting PHIL technology to their research laboratories, providing a major advantage to their students and researchers. However, the complexity, time, and high costs for them to create their own test bench remains a challenge.
-
Product
Partial Discharge Testing Equipment
AR700
-
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
