Isolation Amplifiers
-
Product
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
PCI-9113A
Analog Input Module
ADLINK PCI-9113A is a 32-CH, 12-bit, 100 kS/s isolated analog input card. The PCI-9113A provides analog inputs with 3 programmable input ranges for both bipolar and unipolar inputs. The 32-CH single-ended analog inputs can be converted to 16-CH differential analog inputs, which improve the noise rejection in harsh industrial environments. The analog inputs are isolated from the PC's system ground. This feature not only protects the PC from being damaged from surges on the signal lines, but also eliminates ground loops and common-mode problems commonly seen in industrial measurement applications. The PCI-9113A provides custom circuit area for input signal conditioning. Either signal attenuation or filtering can be applied on per channel basis. With all the features, ADLINK PCI-9113A delivers cost-effective and reliable data acquisition capabilities for ATE, sensor monitoring, data logging, power transmission, and a broad variety of industrial measurement applications.
-
Product
64-Ch Isolated Digital I/O PCIE Card
PCIE-1756
Digital Input PCIe Card
Wide output range (5 ~ 40 VDC)High sink current on isolated output channels (500mA max./ch)Wide input range (10 ~ 30 VDC)High-voltage isolation (2,500 VDC)Interrupt handling capability2,000 VDC ESD protectionEither +/- voltage input for DI by groupHigh over-voltage protection (70 VDC)Output status read-backKeeps the output settings and values after system hot resetChannel-freeze function
-
Product
High Voltage Optically Isolated Probes
-
High Voltage Optically Isolated Probes are designed to aid in device characterization measurements. Whether it is low or high voltage signals sitting on HV busses, high bandwidth, extreme precision, and optical isolation means floating measurements are easily made with minimal DUT loading.
-
Product
PXI 5A Mux 2-Bank 24-Ch Isolated COM
40-651-012
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Power Amplifier
MS 2011
-
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
Product
Digital Input Board, 16 Isolated Channels, 24V
APCI-1016
-
*16 digital inputs, 24 V Optical isolation 1000 V Input filter*Protection against pole reversal*Standard drivers for:*Real time drivers for Windows 2000/NT/98.*The board is supplied with the universal software ADDIPACK.
-
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
Distribution Amplifiers
-
The Quartzlock range of distribution amplifiers are intended for use when multiple outputs from a single frequency standard/generator are required. This may be encountered in engineering labs, national standards labs, research and development, calibration labs and production. This is vital for the distribution of signals from other precision frequency standards like Hydrogen Masers, Cesium oscillators. For a technical discussion about distribution amplifiers go here or select a product range below.
-
Product
High-end Cable DAC & Amplifier
Impacto universal
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Portable Power Amplifier
PA30Bip
-
PA30Bip portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
Product
Amplifier Systems
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies.
-
Product
2-Port Isolated RS-232/422/485 Communication Module
AMAX-5490
Expansion Module
Data Bits: 5, 6, 7, 8Stop Bits: 1, 1.5, 2Parity: None, even, oddBaud Rate: 50 bps ~ 230.4 kbpsData Signals: RS-232: TxD, RxD, GND RS-422: Tx+, Tx-, Rx+, RXRS-485: Data+, Data-FIFO: 256 bytesFlow Control: Xon/Xoff
-
Product
Waveform Amplifier 30 Volts Pk-pk
WA301
-
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
Product
RF POWER AMPLIFIERS
BLWA Series
-
A) RF-Sample PortsI) 3x 208 V AC / 60 HzB) External Dual Directional CouplerL) LAN Remote ControlC) IEEE-488.2 GPIB Remote ControlS) Internal RF Switching UnitD) Front Panel RF ConnectorsR) RS-232C Remote ControlE) RF Power Indication (digital)U) USB Remote ControlF) Gain AdjustmentW) Liquid CoolingH) DC SupplyX) External Control of other Amplifiers
-
Product
High-Voltage Amplifiers - to 1000 Volts peak-to-peak
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
-
Product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
Serial Interface
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Signal Amplifier
ZET 410
-
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
Product
Switch-Mode Isolated Power Supply
-
Renesas offers a wide selection of PWM controllers designed for switch-mode DC/DC and AC/DC power supplies requiring an isolation transformer, such as off-line AC/DC and -48V telecom-input DC/DC converters.
-
Product
Low-Noise Parametric Amplifiers
-
Insight Product Company offers Low-Noise Parametric Amplfiers based on Monolithic Integrated Circuits (MIC) in the frequency range of 30 to 100 GHz.
-
Product
CPCI 48 Optically Isolated Outputs Card
CPCI-48OUT
Controller
The output board consists of FPGA controllers for DC output control. An FPGA provides the timing and control. Each output has its own optical isolation, and supports an open collector output. An PCI controller provides the interface to thehost computer. All I/O is accessible from the front panel.
-
Product
Solid State Power Amplifiers
SSPAs
-
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
Product
FTTx Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s FTTx amplifiers are designed for PON, RFoG and SFU receiver equipment and are offered in small, plastic QFN packages with integrated amplifier and attenuator functions. All parts cover the full 45 to 1000MHz / 1200MHz CATV band. 5v and 12v solutions are offered with power consumption of ≤ 1.5Watts. MACOM’s FTTx amplifiers are characterized with industry standard photodiodes, covering optical input ranges from -12 to +3dBm and each sample EVK comes complete with a photodiode and APC connector.
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
High-Power, Rack-Mount Amplifiers
-
High-power, rackmount amplifiers utilize advanced power combining techniques to achieve high output power levels. These integrated amplifiers include advanced cooling capabilities and other customizable features. Though a focus on modularity, these rackmount amplifiers are ready for easy integration into a larger system or lab test bench.
-
Product
Solid-State RF amplifier module for High Power Testing
-
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
